|
|
|
|
Overview
|
|
|
|
|
=========
|
|
|
|
|
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
|
|
|
|
|
|
|
|
|
|
The P3060 Processor combines six e500mc Power Architecture processor
|
|
|
|
|
cores(1.2GHz) with high-performance datapath acceleration
|
|
|
|
|
architecture(DPAA), CoreNet fabric infrastructure, as well as network
|
|
|
|
|
and peripheral bus interfaces required for networking, telecom/datacom,
|
|
|
|
|
wireless infrastructure, and military/aerospace applications.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P3060QDS Board Specifications:
|
|
|
|
|
==============================
|
|
|
|
|
Memory subsystem:
|
|
|
|
|
* 2G Bytes UDIMM DDR3(64bit bus) with ECC on
|
|
|
|
|
* 128M Bytes NOR flash single-chip memory
|
|
|
|
|
* 16M Bytes SPI flash
|
|
|
|
|
* 8K Bytes AT24C64 I2C EEPROM for RCW
|
|
|
|
|
|
|
|
|
|
Ethernet(Default SERDES 0x19):
|
|
|
|
|
* FM1-dTSEC1: connected to RGMII PHY1 (Vitesse VSC8641 on board,Bottom of dual RJ45)
|
|
|
|
|
* FM1-dTSEC2: connected to RGMII PHY2 (Vitesse VSC8641 on board,Top of dual RJ45)
|
|
|
|
|
* FM1-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port1 in slot1)
|
|
|
|
|
* FM1-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port3 in slot1)
|
|
|
|
|
* FM2-dTSEC1: connected to SGMII PHY (Vitesse VSC8234 port0 in slot2)
|
|
|
|
|
* FM2-dTSEC2: connected to SGMII PHY (Vitesse VSC8234 port2 in slot2)
|
|
|
|
|
* FM2-dTSEC3: connected to SGMII PHY (Vitesse VSC8234 port0 in slot1)
|
|
|
|
|
* FM2-dTSEC4: connected to SGMII PHY (Vitesse VSC8234 port2 in slot1)
|
|
|
|
|
|
|
|
|
|
PCIe:
|
|
|
|
|
* PCIe1: Lanes A, B, C and D of Bank1 are connected to one x4 PCIe SLOT4
|
|
|
|
|
* PCIe2: Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT3
|
|
|
|
|
|
|
|
|
|
RapidIO:
|
|
|
|
|
* sRIO1: Lanes E, F, G and H of Bank1 are connected to sRIO1 (SLOT3)
|
|
|
|
|
* sRIO2: Lanes A, B, C and D of Bank1 are connected to sRIO2 (SLOT4)
|
|
|
|
|
|
|
|
|
|
USB:
|
|
|
|
|
* USB1: connected via an external ULPI PHY SMC3315 to a TYPE-A interface
|
|
|
|
|
* USB2: connected via an external ULPI PHY SMC3315 to a TYPE-AB interface
|
|
|
|
|
|
|
|
|
|
I2C:
|
|
|
|
|
* I2C1_CH0: EEPROM AT24C64(0x50) RCW, AT24C02(0x51) DDR SPD,
|
|
|
|
|
AT24C02(0x53) DDR SPD, AT24C02(0x57) SystemID, RTC DS3232(0x68)
|
|
|
|
|
* I2C1_CH1: 1588 RiserCard(0x55), HSLB Testport, TempMon
|
|
|
|
|
ADT7461(0x4C), SerDesMux DS64MB201(0x51/59/5C/5D)
|
|
|
|
|
* I2C1_CH2: VDD/GVDD/GIDD ZL6100 (0x21/0x22/0x23/0x24/0x40)
|
|
|
|
|
* I2C1_CH3: OCM CFG AT24C02(0x55), OCM IPL AT24C64(0x56)
|
|
|
|
|
* I2C1_CH4: PCIe SLOT1
|
|
|
|
|
* I2C1_CH5: PCIe SLOT2
|
|
|
|
|
* I2C1_CH6: PCIe SLOT3
|
|
|
|
|
* I2C1_CH7: PCIe SLOT4
|
|
|
|
|
* I2C2: NULL
|
|
|
|
|
* I2C3: NULL
|
|
|
|
|
|
|
|
|
|
UART:
|
|
|
|
|
* Supports two UARTs up to 115200 bps for console
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Boot from NOR flash
|
|
|
|
|
===================
|
|
|
|
|
1. Build image
|
|
|
|
|
export ARCH=powerpc
|
|
|
|
|
export CROSS_COMPILE=/your_path/gcc-4.5.xx-eglibc-2.11.xx/powerpc-linux-gnu/bin/powerpc-linux-gnu-
|
|
|
|
|
make P3060QDS_config
|
|
|
|
|
make
|
|
|
|
|
|
|
|
|
|
2. Program image
|
|
|
|
|
=> tftp 1000000 u-boot.bin
|
|
|
|
|
=> protect off all
|
|
|
|
|
=> erase eff80000 efffffff
|
|
|
|
|
=> cp.b 1000000 eff80000 80000
|
|
|
|
|
|
|
|
|
|
3. Program RCW
|
|
|
|
|
=> tftp 1000000 rcw.bin
|
|
|
|
|
=> protect off all
|
|
|
|
|
=> erase e8000000 e801ffff
|
|
|
|
|
=> cp.b 1000000 e8000000 50
|
|
|
|
|
|
|
|
|
|
4. Program FMAN Firmware ucode
|
|
|
|
|
=> tftp 1000000 ucode.bin
|
|
|
|
|
=> protect off all
|
|
|
|
|
=> erase ef000000 ef0fffff
|
|
|
|
|
=> cp.b 1000000 ef000000 2000
|
|
|
|
|
|
|
|
|
|
5. Change DIP-switch
|
|
|
|
|
RCW Location: SW1[1-5] = 01101 (eLBC 16bit NOR flash)
|
|
|
|
|
Note: 1 stands for 'on', 0 stands for 'off'
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Using the Device Tree Source File
|
|
|
|
|
=================================
|
|
|
|
|
To create the DTB (Device Tree Binary) image file, use a command
|
|
|
|
|
similar to this:
|
|
|
|
|
dtc -O dtb -b 0 -p 1024 p3060qds.dts > p3060qds.dtb
|
|
|
|
|
|
|
|
|
|
Or use the following command:
|
|
|
|
|
{linux-2.6}/make p3060qds.dtb ARCH=powerpc
|
|
|
|
|
|
|
|
|
|
then the dtb file will be generated under the following directory:
|
|
|
|
|
{linux-2.6}/arch/powerpc/boot/p3060qds.dtb
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Booting Linux
|
|
|
|
|
=============
|
|
|
|
|
Place a linux uImage in the TFTP disk area.
|
|
|
|
|
tftp 1000000 uImage
|
|
|
|
|
tftp 2000000 rootfs.ext2.gz.uboot
|
|
|
|
|
tftp 3000000 p3060rdb.dtb
|
|
|
|
|
bootm 1000000 2000000 3000000
|
