upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
u-boot/board/kup/common/pcmcia.c

226 lines
5.4 KiB

#include <common.h>
#include <mpc8xx.h>
#include <pcmcia.h>
#undef CONFIG_PCMCIA
#if defined(CONFIG_CMD_PCMCIA)
#define CONFIG_PCMCIA
#endif
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
#define CONFIG_PCMCIA
#endif
#ifdef CONFIG_PCMCIA
#define PCMCIA_BOARD_MSG "KUP"
#define KUP4K_PCMCIA_B_3V3 (0x00020000)
int pcmcia_hardware_enable(int slot)
{
volatile immap_t *immap;
volatile cpm8xx_t *cp;
volatile pcmconf8xx_t *pcmp;
volatile sysconf8xx_t *sysp;
uint reg, mask;
debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
udelay(10000);
immap = (immap_t *)CFG_IMMR;
sysp = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
/*
* Configure SIUMCR to enable PCMCIA port B
* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
*/
sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
/* clear interrupt state, and disable interrupts */
pcmp->pcmc_pscr = PCMCIA_MASK(slot);
pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
/*
* Disable interrupts, DMA, and PCMCIA buffers
* (isolate the interface) and assert RESET signal
*/
debug ("Disable PCMCIA buffers and assert RESET\n");
reg = 0;
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(2500);
/*
* Configure Port B pins for
* 3 Volts enable
*/
if (slot) { /* Slot A is built-in */
cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
/* remove all power */
cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
}
/*
* Make sure there is a card in the slot, then configure the interface.
*/
udelay(10000);
debug ("[%d] %s: PIPR(%p)=0x%x\n",
__LINE__,__FUNCTION__,
&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
printf (" No Card found\n");
return (1);
}
/*
* Power On.
*/
printf("%s Slot %c:", slot ? "" : "\n", 'A' + slot);
mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
reg = pcmp->pcmc_pipr;
debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
reg,
(reg&PCMCIA_VS1(slot))?"n":"ff",
(reg&PCMCIA_VS2(slot))?"n":"ff");
if ((reg & mask) == mask) {
puts (" 5.0V card found: NOT SUPPORTED !!!\n");
} else {
if(slot)
cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
puts (" 3.3V card found: ");
}
#if 0
/* VCC switch error flag, PCMCIA slot INPACK_ pin */
cp->cp_pbdir &= ~(0x0020 | 0x0010);
cp->cp_pbpar &= ~(0x0020 | 0x0010);
udelay(500000);
#endif
debug ("Enable PCMCIA buffers and stop RESET\n");
reg = PCMCIA_PGCRX(slot);
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(250000); /* some cards need >150 ms to come up :-( */
debug ("# hardware_enable done\n");
return (0);
}
#if defined(CONFIG_CMD_PCMCIA)
int pcmcia_hardware_disable(int slot)
{
volatile immap_t *immap;
volatile cpm8xx_t *cp;
volatile pcmconf8xx_t *pcmp;
u_long reg;
debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
immap = (immap_t *)CFG_IMMR;
pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
/* remove all power */
if (slot)
cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
/* Configure PCMCIA General Control Register */
debug ("Disable PCMCIA buffers and assert RESET\n");
reg = 0;
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(10000);
return (0);
}
#endif
int pcmcia_voltage_set(int slot, int vcc, int vpp)
{
volatile immap_t *immap;
volatile cpm8xx_t *cp;
volatile pcmconf8xx_t *pcmp;
u_long reg;
debug ("voltage_set: " \
PCMCIA_BOARD_MSG \
" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
if (!slot) /* Slot A is not configurable */
return 0;
immap = (immap_t *)CFG_IMMR;
pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
cp = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
/*
* Disable PCMCIA buffers (isolate the interface)
* and assert RESET signal
*/
debug ("Disable PCMCIA buffers and assert RESET\n");
reg = PCMCIA_PGCRX(slot);
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(500);
debug ("PCMCIA power OFF\n");
/*
* Configure Port B pins for
* 3 Volts enable
*/
cp->cp_pbdir |= KUP4K_PCMCIA_B_3V3;
cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
/* remove all power */
cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3; /* active low */
switch(vcc) {
case 0: break;
case 33:
cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
debug ("PCMCIA powered at 3.3V\n");
break;
case 50:
debug ("PCMCIA: 5Volt vcc not supported\n");
break;
default:
puts("PCMCIA: vcc not supported");
break;
}
udelay(10000);
/* Checking supported voltages */
debug ("PIPR: 0x%x --> %s\n",
pcmp->pcmc_pipr,
(pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
? "only 5 V --> NOT SUPPORTED"
: "can do 3.3V");
debug ("Enable PCMCIA buffers and stop RESET\n");
reg = PCMCIA_PGCRX(slot);
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(500);
debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
slot+'A');
return (0);
}
#endif /* CONFIG_PCMCIA */