upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
u-boot/board/renesas/sh7785lcr/README.sh7785lcr

124 lines
3.1 KiB

========================================
Renesas Technology R0P7785LC0011RL board
========================================
This board specification:
=========================
The R0P7785LC0011RL(board config name:sh7785lcr) has the following device:
- SH7785 (SH-4A)
- DDR2-SDRAM 512MB
- NOR Flash 64MB
- 2D Graphic controller
- SATA controller
- Ethernet controller
- USB host/peripheral controller
- SD controller
- I2C controller
- RTC
This board has 2 physical memory maps. It can be changed with DIP switch(S2-5).
phys address | S2-5 = OFF | S2-5 = ON
-------------------------------+---------------+---------------
0x00000000 - 0x03ffffff(CS0) | NOR Flash | NOR Flash
0x04000000 - 0x05ffffff(CS1) | PLD | PLD
0x06000000 - 0x07ffffff(CS1) | reserved | I2C
0x08000000 - 0x0bffffff(CS2) | USB | DDR SDRAM
0x0c000000 - 0x0fffffff(CS3) | SD | DDR SDRAM
0x10000000 - 0x13ffffff(CS4) | SM107 | SM107
0x14000000 - 0x17ffffff(CS5) | I2C | USB
0x18000000 - 0x1bffffff(CS6) | reserved | SD
0x40000000 - 0x5fffffff | DDR SDRAM | (cannot use)
configuration for This board:
=============================
You can choose configuration as follows:
- make sh7785lcr_config
- make sh7785lcr_32bit_config
When you use "make sh7785lcr_config", there is build U-Boot for 29-bit
address mode. This mode can use 128MB DDR-SDRAM.
When you use "make sh7785lcr_32bit_config", there is build U-Boot for 32-bit
extended address mode. This mode can use 384MB DDR-SDRAM. And if you run
"pmb" command, this mode can use 512MB DDR-SDRAM.
* 32-bit extended address mode PMB mapping *
a) on start-up
virt | phys | size | device
-------------+---------------+---------------+---------------
0x88000000 | 0x48000000 | 384MB | DDR-SDRAM (Cacheable)
0xa0000000 | 0x00000000 | 64MB | NOR Flash
0xa4000000 | 0x04000000 | 16MB | PLD
0xa6000000 | 0x08000000 | 16MB | USB
0xa8000000 | 0x48000000 | 384MB | DDR-SDRAM (Non-cacheable)
b) after "pmb" command
virt | phys | size | device
-------------+---------------+---------------+---------------
0x80000000 | 0x40000000 | 512MB | DDR-SDRAM (Cacheable)
0xa0000000 | 0x40000000 | 512MB | DDR-SDRAM (Non-cacheable)
This board specific command:
============================
This board has the following its specific command:
- hwtest
- printmac
- setmac
- pmb (sh7785lcr_32bit_config only)
1. hwtest
This is self-check command. This command has the following options:
- all : test all hardware
- pld : output PLD version
- led : turn on LEDs
- dipsw : test DIP switch
- sm107 : output SM107 version
- net : check RTL8110 ID
- sata : check SiI3512 ID
- net : output PCI slot device ID
i.e)
=> hwtest led
turn on LEDs 3, 5, 7, 9
turn on LEDs 4, 6, 8, 10
=> hwtest net
Ethernet OK
2. printmac
This command outputs MAC address of this board.
i.e)
=> printmac
MAC = 00:00:87:**:**:**
3. setmac
This command writes MAC address of this board.
i.e)
=> setmac 00:00:87:**:**:**
4. pmb
This command change PMB for DDR-SDRAM all mapping. However you cannot use
NOR Flash and USB Host on U-Boot when you run this command.
i.e)
=> pmb