upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
86 lines
1.9 KiB
86 lines
1.9 KiB
11 years ago
|
/*
|
||
|
|
* (C) Copyright 2013
|
||
|
|
* Avionic Design GmbH <www.avionic-design.de>
|
||
|
|
*
|
||
|
|
* SPDX-License-Identifier: GPL-2.0+
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <common.h>
|
||
|
|
#include <asm/arch/pinmux.h>
|
||
|
|
#include <asm/arch/gp_padctrl.h>
|
||
|
|
#include <asm/arch/gpio.h>
|
||
|
|
#include <asm/gpio.h>
|
||
|
|
#include "pinmux-config-tamonten-ng.h"
|
||
|
|
#include <i2c.h>
|
||
|
|
|
||
|
|
#define PMU_I2C_ADDRESS 0x2D
|
||
|
|
|
||
|
|
#define PMU_REG_LDO5 0x32
|
||
|
|
|
||
|
|
#define PMU_REG_LDO_HIGH_POWER 1
|
||
|
|
|
||
|
|
/* Voltage selection for the LDOs with 100mV resolution */
|
||
|
|
#define PMU_REG_LDO_SEL_100(mV) ((((mV - 1000) / 100) + 2) << 2)
|
||
|
|
|
||
|
|
#define PMU_REG_LDO_100(st, mV) (PMU_REG_LDO_##st | PMU_REG_LDO_SEL_100(mV))
|
||
|
|
|
||
|
|
#define PMU_LDO5(st, mV) PMU_REG_LDO_100(st, mV)
|
||
|
|
|
||
|
|
void pinmux_init(void)
|
||
|
|
{
|
||
|
|
pinmux_config_table(tamonten_ng_pinmux_common,
|
||
|
|
ARRAY_SIZE(tamonten_ng_pinmux_common));
|
||
|
|
pinmux_config_table(unused_pins_lowpower,
|
||
|
|
ARRAY_SIZE(unused_pins_lowpower));
|
||
|
|
|
||
|
|
/* Initialize any non-default pad configs (APB_MISC_GP regs) */
|
||
|
|
padgrp_config_table(tamonten_ng_padctrl,
|
||
|
|
ARRAY_SIZE(tamonten_ng_padctrl));
|
||
|
|
}
|
||
|
|
|
||
|
|
void gpio_early_init(void)
|
||
|
|
{
|
||
|
|
/* Turn on the alive signal */
|
||
|
|
gpio_request(GPIO_PV2, "ALIVE");
|
||
|
|
gpio_direction_output(GPIO_PV2, 1);
|
||
|
|
|
||
|
|
/* Remove the reset on the external periph */
|
||
|
|
gpio_request(GPIO_PI4, "nRST_PERIPH");
|
||
|
|
gpio_direction_output(GPIO_PI4, 1);
|
||
|
|
}
|
||
|
|
|
||
|
|
void pmu_write(uchar reg, uchar data)
|
||
|
|
{
|
||
|
|
i2c_set_bus_num(4); /* PMU is on bus 4 */
|
||
|
|
i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1);
|
||
|
|
}
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Do I2C/PMU writes to bring up SD card bus power
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
void board_sdmmc_voltage_init(void)
|
||
|
|
{
|
||
|
|
/* Enable LDO5 with 3.3v for SDMMC3 */
|
||
|
|
pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
|
||
|
|
|
||
|
|
/* Switch the power on */
|
||
|
|
gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
|
||
|
|
gpio_direction_output(GPIO_PJ2, 1);
|
||
|
|
}
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Routine: pin_mux_mmc
|
||
|
|
* Description: setup the MMC muxes, power rails, etc.
|
||
|
|
*/
|
||
|
|
void pin_mux_mmc(void)
|
||
|
|
{
|
||
|
|
/*
|
||
|
|
* NOTE: We don't do mmc-specific pin muxes here.
|
||
|
|
* They were done globally in pinmux_init().
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Bring up the SDIO1 power rail */
|
||
|
|
board_sdmmc_voltage_init();
|
||
|
|
}
|