upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
u-boot/board/ti/omap1510inn/omap1510innovator.c

142 lines
3.6 KiB

/*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* (C) Copyright 2002
* David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
*
* (C) Copyright 2003
* Texas Instruments, <www.ti.com>
* Kshitij Gupta <Kshitij@ti.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
static void flash__init (void);
static void ether__init (void);
static inline void delay (unsigned long loops)
{
__asm__ volatile ("1:\n"
"subs %0, %1, #1\n"
"bne 1b":"=r" (loops):"0" (loops));
}
/*
* Miscellaneous platform dependent initialisations
*/
int board_init (void)
{
/* arch number of OMAP 1510-Board */
gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x10000100;
/* kk - this speeds up your boot a quite a bit. However to make it
* work, you need make sure your kernel startup flush bug is fixed.
* ... rkw ...
*/
icache_enable ();
flash__init ();
ether__init ();
return 0;
}
int misc_init_r (void)
{
/* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
/* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
/* setup gpio direction to match board (no floats!) */
/**gdir = 0xCFF9; */
/**mdir = 0x103F; */
return (0);
}
/******************************
Routine:
Description:
******************************/
static void flash__init (void)
{
#define CS0_CHIP_SELECT_REG 0xfffecc10
#define CS3_CHIP_SELECT_REG 0xfffecc1c
#define EMIFS_GlB_Config_REG 0xfffecc0c
{
unsigned int regval;
regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
regval = regval | 0x0001; /* Turn off write protection for flash devices. */
if (regval & 0x0002) {
regval = regval & 0xfffd; /* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
/* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
/* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
/* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
}
*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
}
}
/******************************
Routine:
Description:
******************************/
static void ether__init (void)
{
#define ETH_CONTROL_REG 0x0800000b
/* take the Ethernet controller out of reset and wait
* for the EEPROM load to complete.
*/
*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
udelay (3);
}
int dram_init (void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
return 0;
}
#ifdef CONFIG_CMD_NET
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_LAN91C96
rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
#endif
return rc;
}
#endif