Add a SPI NAND framework based on the generic NAND framework and the spi-mem infrastructure. In its current state, this framework supports the following features: - single/dual/quad IO modes - on-die ECC Signed-off-by: Peter Pan <peterpandong@micron.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Jagan Teki <jagan@openedev.com>lime2-spi
parent
d13f5b254a
commit
0a6d6bae03
@ -0,0 +1,7 @@ |
||||
menuconfig MTD_SPI_NAND |
||||
bool "SPI NAND device Support" |
||||
depends on MTD && DM_SPI |
||||
select MTD_NAND_CORE |
||||
select SPI_MEM |
||||
help |
||||
This is the framework for the SPI NAND device drivers. |
@ -0,0 +1,4 @@ |
||||
# SPDX-License-Identifier: GPL-2.0
|
||||
|
||||
spinand-objs := core.o
|
||||
obj-$(CONFIG_MTD_SPI_NAND) += spinand.o
|
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,427 @@ |
||||
/* SPDX-License-Identifier: GPL-2.0 */ |
||||
/*
|
||||
* Copyright (c) 2016-2017 Micron Technology, Inc. |
||||
* |
||||
* Authors: |
||||
* Peter Pan <peterpandong@micron.com> |
||||
*/ |
||||
#ifndef __LINUX_MTD_SPINAND_H |
||||
#define __LINUX_MTD_SPINAND_H |
||||
|
||||
#ifndef __UBOOT__ |
||||
#include <linux/mutex.h> |
||||
#include <linux/bitops.h> |
||||
#include <linux/device.h> |
||||
#include <linux/mtd/mtd.h> |
||||
#include <linux/mtd/nand.h> |
||||
#include <linux/spi/spi.h> |
||||
#include <linux/spi/spi-mem.h> |
||||
#else |
||||
#include <common.h> |
||||
#include <spi.h> |
||||
#include <spi-mem.h> |
||||
#include <linux/mtd/nand.h> |
||||
#endif |
||||
|
||||
/**
|
||||
* Standard SPI NAND flash operations |
||||
*/ |
||||
|
||||
#define SPINAND_RESET_OP \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0xff, 1), \
|
||||
SPI_MEM_OP_NO_ADDR, \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_NO_DATA) |
||||
|
||||
#define SPINAND_WR_EN_DIS_OP(enable) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD((enable) ? 0x06 : 0x04, 1), \
|
||||
SPI_MEM_OP_NO_ADDR, \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_NO_DATA) |
||||
|
||||
#define SPINAND_READID_OP(ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x9f, 1), \
|
||||
SPI_MEM_OP_NO_ADDR, \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 1), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 1)) |
||||
|
||||
#define SPINAND_SET_FEATURE_OP(reg, valptr) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x1f, 1), \
|
||||
SPI_MEM_OP_ADDR(1, reg, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_DATA_OUT(1, valptr, 1)) |
||||
|
||||
#define SPINAND_GET_FEATURE_OP(reg, valptr) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x0f, 1), \
|
||||
SPI_MEM_OP_ADDR(1, reg, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_DATA_IN(1, valptr, 1)) |
||||
|
||||
#define SPINAND_BLK_ERASE_OP(addr) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0xd8, 1), \
|
||||
SPI_MEM_OP_ADDR(3, addr, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_NO_DATA) |
||||
|
||||
#define SPINAND_PAGE_READ_OP(addr) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x13, 1), \
|
||||
SPI_MEM_OP_ADDR(3, addr, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_NO_DATA) |
||||
|
||||
#define SPINAND_PAGE_READ_FROM_CACHE_OP(fast, addr, ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(fast ? 0x0b : 0x03, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 1), \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 1), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 1)) |
||||
|
||||
#define SPINAND_PAGE_READ_FROM_CACHE_X2_OP(addr, ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x3b, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 1), \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 1), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 2)) |
||||
|
||||
#define SPINAND_PAGE_READ_FROM_CACHE_X4_OP(addr, ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x6b, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 1), \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 1), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 4)) |
||||
|
||||
#define SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(addr, ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0xbb, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 2), \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 2), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 2)) |
||||
|
||||
#define SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(addr, ndummy, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0xeb, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 4), \
|
||||
SPI_MEM_OP_DUMMY(ndummy, 4), \
|
||||
SPI_MEM_OP_DATA_IN(len, buf, 4)) |
||||
|
||||
#define SPINAND_PROG_EXEC_OP(addr) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(0x10, 1), \
|
||||
SPI_MEM_OP_ADDR(3, addr, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_NO_DATA) |
||||
|
||||
#define SPINAND_PROG_LOAD(reset, addr, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x02 : 0x84, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_DATA_OUT(len, buf, 1)) |
||||
|
||||
#define SPINAND_PROG_LOAD_X4(reset, addr, buf, len) \ |
||||
SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x32 : 0x34, 1), \
|
||||
SPI_MEM_OP_ADDR(2, addr, 1), \
|
||||
SPI_MEM_OP_NO_DUMMY, \
|
||||
SPI_MEM_OP_DATA_OUT(len, buf, 4)) |
||||
|
||||
/**
|
||||
* Standard SPI NAND flash commands |
||||
*/ |
||||
#define SPINAND_CMD_PROG_LOAD_X4 0x32 |
||||
#define SPINAND_CMD_PROG_LOAD_RDM_DATA_X4 0x34 |
||||
|
||||
/* feature register */ |
||||
#define REG_BLOCK_LOCK 0xa0 |
||||
#define BL_ALL_UNLOCKED 0x00 |
||||
|
||||
/* configuration register */ |
||||
#define REG_CFG 0xb0 |
||||
#define CFG_OTP_ENABLE BIT(6) |
||||
#define CFG_ECC_ENABLE BIT(4) |
||||
#define CFG_QUAD_ENABLE BIT(0) |
||||
|
||||
/* status register */ |
||||
#define REG_STATUS 0xc0 |
||||
#define STATUS_BUSY BIT(0) |
||||
#define STATUS_ERASE_FAILED BIT(2) |
||||
#define STATUS_PROG_FAILED BIT(3) |
||||
#define STATUS_ECC_MASK GENMASK(5, 4) |
||||
#define STATUS_ECC_NO_BITFLIPS (0 << 4) |
||||
#define STATUS_ECC_HAS_BITFLIPS (1 << 4) |
||||
#define STATUS_ECC_UNCOR_ERROR (2 << 4) |
||||
|
||||
struct spinand_op; |
||||
struct spinand_device; |
||||
|
||||
#define SPINAND_MAX_ID_LEN 4 |
||||
|
||||
/**
|
||||
* struct spinand_id - SPI NAND id structure |
||||
* @data: buffer containing the id bytes. Currently 4 bytes large, but can |
||||
* be extended if required |
||||
* @len: ID length |
||||
* |
||||
* struct_spinand_id->data contains all bytes returned after a READ_ID command, |
||||
* including dummy bytes if the chip does not emit ID bytes right after the |
||||
* READ_ID command. The responsibility to extract real ID bytes is left to |
||||
* struct_manufacurer_ops->detect(). |
||||
*/ |
||||
struct spinand_id { |
||||
u8 data[SPINAND_MAX_ID_LEN]; |
||||
int len; |
||||
}; |
||||
|
||||
/**
|
||||
* struct manufacurer_ops - SPI NAND manufacturer specific operations |
||||
* @detect: detect a SPI NAND device. Every time a SPI NAND device is probed |
||||
* the core calls the struct_manufacurer_ops->detect() hook of each |
||||
* registered manufacturer until one of them return 1. Note that |
||||
* the first thing to check in this hook is that the manufacturer ID |
||||
* in struct_spinand_device->id matches the manufacturer whose |
||||
* ->detect() hook has been called. Should return 1 if there's a |
||||
* match, 0 if the manufacturer ID does not match and a negative |
||||
* error code otherwise. When true is returned, the core assumes |
||||
* that properties of the NAND chip (spinand->base.memorg and |
||||
* spinand->base.eccreq) have been filled |
||||
* @init: initialize a SPI NAND device |
||||
* @cleanup: cleanup a SPI NAND device |
||||
* |
||||
* Each SPI NAND manufacturer driver should implement this interface so that |
||||
* NAND chips coming from this vendor can be detected and initialized properly. |
||||
*/ |
||||
struct spinand_manufacturer_ops { |
||||
int (*detect)(struct spinand_device *spinand); |
||||
int (*init)(struct spinand_device *spinand); |
||||
void (*cleanup)(struct spinand_device *spinand); |
||||
}; |
||||
|
||||
/**
|
||||
* struct spinand_manufacturer - SPI NAND manufacturer instance |
||||
* @id: manufacturer ID |
||||
* @name: manufacturer name |
||||
* @ops: manufacturer operations |
||||
*/ |
||||
struct spinand_manufacturer { |
||||
u8 id; |
||||
char *name; |
||||
const struct spinand_manufacturer_ops *ops; |
||||
}; |
||||
|
||||
/**
|
||||
* struct spinand_op_variants - SPI NAND operation variants |
||||
* @ops: the list of variants for a given operation |
||||
* @nops: the number of variants |
||||
* |
||||
* Some operations like read-from-cache/write-to-cache have several variants |
||||
* depending on the number of IO lines you use to transfer data or address |
||||
* cycles. This structure is a way to describe the different variants supported |
||||
* by a chip and let the core pick the best one based on the SPI mem controller |
||||
* capabilities. |
||||
*/ |
||||
struct spinand_op_variants { |
||||
const struct spi_mem_op *ops; |
||||
unsigned int nops; |
||||
}; |
||||
|
||||
#define SPINAND_OP_VARIANTS(name, ...) \ |
||||
const struct spinand_op_variants name = { \
|
||||
.ops = (struct spi_mem_op[]) { __VA_ARGS__ }, \
|
||||
.nops = sizeof((struct spi_mem_op[]){ __VA_ARGS__ }) / \
|
||||
sizeof(struct spi_mem_op), \
|
||||
} |
||||
|
||||
/**
|
||||
* spinand_ecc_info - description of the on-die ECC implemented by a SPI NAND |
||||
* chip |
||||
* @get_status: get the ECC status. Should return a positive number encoding |
||||
* the number of corrected bitflips if correction was possible or |
||||
* -EBADMSG if there are uncorrectable errors. I can also return |
||||
* other negative error codes if the error is not caused by |
||||
* uncorrectable bitflips |
||||
* @ooblayout: the OOB layout used by the on-die ECC implementation |
||||
*/ |
||||
struct spinand_ecc_info { |
||||
int (*get_status)(struct spinand_device *spinand, u8 status); |
||||
const struct mtd_ooblayout_ops *ooblayout; |
||||
}; |
||||
|
||||
#define SPINAND_HAS_QE_BIT BIT(0) |
||||
|
||||
/**
|
||||
* struct spinand_info - Structure used to describe SPI NAND chips |
||||
* @model: model name |
||||
* @devid: device ID |
||||
* @flags: OR-ing of the SPINAND_XXX flags |
||||
* @memorg: memory organization |
||||
* @eccreq: ECC requirements |
||||
* @eccinfo: on-die ECC info |
||||
* @op_variants: operations variants |
||||
* @op_variants.read_cache: variants of the read-cache operation |
||||
* @op_variants.write_cache: variants of the write-cache operation |
||||
* @op_variants.update_cache: variants of the update-cache operation |
||||
* @select_target: function used to select a target/die. Required only for |
||||
* multi-die chips |
||||
* |
||||
* Each SPI NAND manufacturer driver should have a spinand_info table |
||||
* describing all the chips supported by the driver. |
||||
*/ |
||||
struct spinand_info { |
||||
const char *model; |
||||
u8 devid; |
||||
u32 flags; |
||||
struct nand_memory_organization memorg; |
||||
struct nand_ecc_req eccreq; |
||||
struct spinand_ecc_info eccinfo; |
||||
struct { |
||||
const struct spinand_op_variants *read_cache; |
||||
const struct spinand_op_variants *write_cache; |
||||
const struct spinand_op_variants *update_cache; |
||||
} op_variants; |
||||
int (*select_target)(struct spinand_device *spinand, |
||||
unsigned int target); |
||||
}; |
||||
|
||||
#define SPINAND_INFO_OP_VARIANTS(__read, __write, __update) \ |
||||
{ \
|
||||
.read_cache = __read, \
|
||||
.write_cache = __write, \
|
||||
.update_cache = __update, \
|
||||
} |
||||
|
||||
#define SPINAND_ECCINFO(__ooblayout, __get_status) \ |
||||
.eccinfo = { \
|
||||
.ooblayout = __ooblayout, \
|
||||
.get_status = __get_status, \
|
||||
} |
||||
|
||||
#define SPINAND_SELECT_TARGET(__func) \ |
||||
.select_target = __func, |
||||
|
||||
#define SPINAND_INFO(__model, __id, __memorg, __eccreq, __op_variants, \ |
||||
__flags, ...) \
|
||||
{ \
|
||||
.model = __model, \
|
||||
.devid = __id, \
|
||||
.memorg = __memorg, \
|
||||
.eccreq = __eccreq, \
|
||||
.op_variants = __op_variants, \
|
||||
.flags = __flags, \
|
||||
__VA_ARGS__ \
|
||||
} |
||||
|
||||
/**
|
||||
* struct spinand_device - SPI NAND device instance |
||||
* @base: NAND device instance |
||||
* @slave: pointer to the SPI slave object |
||||
* @lock: lock used to serialize accesses to the NAND |
||||
* @id: NAND ID as returned by READ_ID |
||||
* @flags: NAND flags |
||||
* @op_templates: various SPI mem op templates |
||||
* @op_templates.read_cache: read cache op template |
||||
* @op_templates.write_cache: write cache op template |
||||
* @op_templates.update_cache: update cache op template |
||||
* @select_target: select a specific target/die. Usually called before sending |
||||
* a command addressing a page or an eraseblock embedded in |
||||
* this die. Only required if your chip exposes several dies |
||||
* @cur_target: currently selected target/die |
||||
* @eccinfo: on-die ECC information |
||||
* @cfg_cache: config register cache. One entry per die |
||||
* @databuf: bounce buffer for data |
||||
* @oobbuf: bounce buffer for OOB data |
||||
* @scratchbuf: buffer used for everything but page accesses. This is needed |
||||
* because the spi-mem interface explicitly requests that buffers |
||||
* passed in spi_mem_op be DMA-able, so we can't based the bufs on |
||||
* the stack |
||||
* @manufacturer: SPI NAND manufacturer information |
||||
* @priv: manufacturer private data |
||||
*/ |
||||
struct spinand_device { |
||||
struct nand_device base; |
||||
#ifndef __UBOOT__ |
||||
struct spi_mem *spimem; |
||||
struct mutex lock; |
||||
#else |
||||
struct spi_slave *slave; |
||||
#endif |
||||
struct spinand_id id; |
||||
u32 flags; |
||||
|
||||
struct { |
||||
const struct spi_mem_op *read_cache; |
||||
const struct spi_mem_op *write_cache; |
||||
const struct spi_mem_op *update_cache; |
||||
} op_templates; |
||||
|
||||
int (*select_target)(struct spinand_device *spinand, |
||||
unsigned int target); |
||||
unsigned int cur_target; |
||||
|
||||
struct spinand_ecc_info eccinfo; |
||||
|
||||
u8 *cfg_cache; |
||||
u8 *databuf; |
||||
u8 *oobbuf; |
||||
u8 *scratchbuf; |
||||
const struct spinand_manufacturer *manufacturer; |
||||
void *priv; |
||||
}; |
||||
|
||||
/**
|
||||
* mtd_to_spinand() - Get the SPI NAND device attached to an MTD instance |
||||
* @mtd: MTD instance |
||||
* |
||||
* Return: the SPI NAND device attached to @mtd. |
||||
*/ |
||||
static inline struct spinand_device *mtd_to_spinand(struct mtd_info *mtd) |
||||
{ |
||||
return container_of(mtd_to_nanddev(mtd), struct spinand_device, base); |
||||
} |
||||
|
||||
/**
|
||||
* spinand_to_mtd() - Get the MTD device embedded in a SPI NAND device |
||||
* @spinand: SPI NAND device |
||||
* |
||||
* Return: the MTD device embedded in @spinand. |
||||
*/ |
||||
static inline struct mtd_info *spinand_to_mtd(struct spinand_device *spinand) |
||||
{ |
||||
return nanddev_to_mtd(&spinand->base); |
||||
} |
||||
|
||||
/**
|
||||
* nand_to_spinand() - Get the SPI NAND device embedding an NAND object |
||||
* @nand: NAND object |
||||
* |
||||
* Return: the SPI NAND device embedding @nand. |
||||
*/ |
||||
static inline struct spinand_device *nand_to_spinand(struct nand_device *nand) |
||||
{ |
||||
return container_of(nand, struct spinand_device, base); |
||||
} |
||||
|
||||
/**
|
||||
* spinand_to_nand() - Get the NAND device embedded in a SPI NAND object |
||||
* @spinand: SPI NAND device |
||||
* |
||||
* Return: the NAND device embedded in @spinand. |
||||
*/ |
||||
static inline struct nand_device * |
||||
spinand_to_nand(struct spinand_device *spinand) |
||||
{ |
||||
return &spinand->base; |
||||
} |
||||
|
||||
/**
|
||||
* spinand_set_of_node - Attach a DT node to a SPI NAND device |
||||
* @spinand: SPI NAND device |
||||
* @np: DT node |
||||
* |
||||
* Attach a DT node to a SPI NAND device. |
||||
*/ |
||||
static inline void spinand_set_of_node(struct spinand_device *spinand, |
||||
const struct device_node *np) |
||||
{ |
||||
nanddev_set_of_node(&spinand->base, np); |
||||
} |
||||
|
||||
int spinand_match_and_init(struct spinand_device *dev, |
||||
const struct spinand_info *table, |
||||
unsigned int table_size, u8 devid); |
||||
|
||||
int spinand_upd_cfg(struct spinand_device *spinand, u8 mask, u8 val); |
||||
int spinand_select_target(struct spinand_device *spinand, unsigned int target); |
||||
|
||||
#endif /* __LINUX_MTD_SPINAND_H */ |
Loading…
Reference in new issue