Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

ARM DaVinci: Add common peripherals and modules enable functions.

Browse Source 
Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
master
Hugo Villeneuve 16 years ago committed by Jean-Christophe PLAGNIOL-VILLARD
parent d3be1bcae7
commit 0cd18fa982
6 changed files with 101 additions and 105 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 65
      board/davinci/common/psc.c
  2. 3
      board/davinci/common/psc.h
  3. 35
      board/davinci/dvevm/dvevm.c
  4. 37
      board/davinci/schmoogie/schmoogie.c
  5. 31
      board/davinci/sffsdr/sffsdr.c
  6. 35
      board/davinci/sonata/sonata.c

65
board/davinci/common/psc.c
Unescape View File

@ -26,6 +26,14 @@
#include <common.h>
#include <asm/arch/hardware.h>
#define PINMUX0_EMACEN (1 << 31)
#define PINMUX0_AECS5 (1 << 11)
#define PINMUX0_AECS4 (1 << 10)
#define PINMUX1_I2C (1 << 7)
#define PINMUX1_UART1 (1 << 1)
#define PINMUX1_UART0 (1 << 0)
/*
* The DM6446 includes two separate power domains: "Always On" and "DSP". The
* "Always On" power domain is always on when the chip is on. The "Always On"
@ -115,3 +123,60 @@ void dsp_on(void)
REG(PSC_GBLCTL) &= ~0x1f;
}
#endif /* CONFIG_SYS_USE_DSPLINK */
void davinci_enable_uart0(void)
{
lpsc_on(DAVINCI_LPSC_UART0);
/* Bringup UART0 out of reset */
REG(UART0_PWREMU_MGMT) = 0x0000e003;
/* Enable UART0 MUX lines */
REG(PINMUX1) |= PINMUX1_UART0;
}
#ifdef CONFIG_DRIVER_TI_EMAC
void davinci_enable_emac(void)
{
lpsc_on(DAVINCI_LPSC_EMAC);
lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
lpsc_on(DAVINCI_LPSC_MDIO);
/* Enable GIO3.3V cells used for EMAC */
REG(VDD3P3V_PWDN) = 0;
/* Enable EMAC. */
REG(PINMUX0) |= PINMUX0_EMACEN;
}
#endif
void davinci_enable_i2c(void)
{
lpsc_on(DAVINCI_LPSC_I2C);
/* Enable I2C pin Mux */
REG(PINMUX1) |= PINMUX1_I2C;
}
void davinci_errata_workarounds(void)
{
/*
* Workaround for TMS320DM6446 errata 1.3.22:
* PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset
* Revision(s) Affected: 1.3 and earlier
*/
REG(PSC_SILVER_BULLET) = 0;
/*
* Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR)
* as suggested in TMS320DM6446 errata 2.1.2:
*
* On DM6446 Silicon Revision 2.1 and earlier, under certain conditions
* low priority modules can occupy the bus and prevent high priority
* modules like the VPSS from getting the required DDR2 throughput.
* A hex value of 0x20 should provide a good ARM (cache enabled)
* performance and still allow good utilization by the VPSS or other
* modules.
*/
REG(VBPR) = 0x20;
}

3
board/davinci/common/psc.h
Unescape View File

@ -24,5 +24,8 @@
void lpsc_on(unsigned int id);
void dsp_on(void);
void davinci_enable_uart0(void);
void davinci_enable_emac(void);
void davinci_enable_i2c(void);
#endif /* __PSC_H */

35
board/davinci/dvevm/dvevm.c
Unescape View File

@ -27,7 +27,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@ -41,16 +40,13 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/* Workaround for TMS320DM6446 errata 1.3.22 */
REG(PSC_SILVER_BULLET) = 0;
/* Configure AEMIF pins (although this should be configured at boot time
* with pull-up/pull-down resistors) */
REG(PINMUX0) = 0x00000c1f;
davinci_errata_workarounds();
/* Power on required peripherals */
lpsc_on(DAVINCI_LPSC_EMAC);
lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
lpsc_on(DAVINCI_LPSC_MDIO);
lpsc_on(DAVINCI_LPSC_I2C);
lpsc_on(DAVINCI_LPSC_UART0);
lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
lpsc_on(DAVINCI_LPSC_USB);
@ -59,24 +55,11 @@ int board_init(void)
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
/* Bringup UART0 out of reset */
REG(UART0_PWREMU_MGMT) = 0x0000e003;
/* Enable GIO3.3V cells used for EMAC */
REG(VDD3P3V_PWDN) = 0;
/* Enable UART0 MUX lines */
REG(PINMUX1) |= 1;
/* Enable EMAC and AEMIF pins */
REG(PINMUX0) = 0x80000c1f;
/* Enable I2C pin Mux */
REG(PINMUX1) |= (1 << 7);
/* Set the Bus Priority Register to appropriate value */
REG(VBPR) = 0x20;
davinci_enable_uart0();
davinci_enable_emac();
davinci_enable_i2c();
lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);

37
board/davinci/schmoogie/schmoogie.c
Unescape View File

@ -27,7 +27,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@ -41,16 +40,13 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/* Workaround for TMS320DM6446 errata 1.3.22 */
REG(PSC_SILVER_BULLET) = 0;
/* Configure AEMIF pins (although this should be configured at boot time
* with pull-up/pull-down resistors) */
REG(PINMUX0) = 0x00000c1f;
davinci_errata_workarounds();
/* Power on required peripherals */
lpsc_on(DAVINCI_LPSC_EMAC);
lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
lpsc_on(DAVINCI_LPSC_MDIO);
lpsc_on(DAVINCI_LPSC_I2C);
lpsc_on(DAVINCI_LPSC_UART0);
lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@ -58,24 +54,11 @@ int board_init(void)
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
/* Bringup UART0 out of reset */
REG(UART0_PWREMU_MGMT) = 0x0000e003;
/* Enable GIO3.3V cells used for EMAC */
REG(VDD3P3V_PWDN) = 0;
/* Enable UART0 MUX lines */
REG(PINMUX1) |= 1;
/* Enable EMAC and AEMIF pins */
REG(PINMUX0) = 0x80000c1f;
/* Enable I2C pin Mux */
REG(PINMUX1) |= (1 << 7);
/* Set the Bus Priority Register to appropriate value */
REG(VBPR) = 0x20;
davinci_enable_uart0();
davinci_enable_emac();
davinci_enable_i2c();
lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);
@ -87,7 +70,7 @@ int misc_init_r(void)
int i = 0;
/* Set serial number from UID chip */
u_int8_t crc_tbl[256] = {
const u_int8_t crc_tbl[256] = {
0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83,
0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41,
0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e,

31
board/davinci/sffsdr/sffsdr.c
Unescape View File

@ -30,7 +30,6 @@
#include <common.h>
#include <i2c.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@ -51,16 +50,9 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/* Workaround for TMS320DM6446 errata 1.3.22 */
REG(PSC_SILVER_BULLET) = 0;
davinci_errata_workarounds();
/* Power on required peripherals */
lpsc_on(DAVINCI_LPSC_EMAC);
lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
lpsc_on(DAVINCI_LPSC_MDIO);
lpsc_on(DAVINCI_LPSC_I2C);
lpsc_on(DAVINCI_LPSC_UART0);
lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@ -68,24 +60,11 @@ int board_init(void)
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
/* Bringup UART0 out of reset */
REG(UART0_PWREMU_MGMT) = 0x0000e003;
/* Enable GIO3.3V cells used for EMAC */
REG(VDD3P3V_PWDN) = 0;
/* Enable UART0 MUX lines */
REG(PINMUX1) |= 1;
/* Enable EMAC and AEMIF pins */
REG(PINMUX0) = 0x80000c1f;
/* Enable I2C pin Mux */
REG(PINMUX1) |= (1 << 7);
/* Set the Bus Priority Register to appropriate value */
REG(VBPR) = 0x20;
davinci_enable_uart0();
davinci_enable_emac();
davinci_enable_i2c();
lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);

35
board/davinci/sonata/sonata.c
Unescape View File

@ -26,7 +26,6 @@
#include <common.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emac_defs.h>
#include "../common/psc.h"
#include "../common/misc.h"
@ -40,16 +39,13 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/* Workaround for TMS320DM6446 errata 1.3.22 */
REG(PSC_SILVER_BULLET) = 0;
/* Configure AEMIF pins (although this should be configured at boot time
* with pull-up/pull-down resistors) */
REG(PINMUX0) = 0x00000c1f;
davinci_errata_workarounds();
/* Power on required peripherals */
lpsc_on(DAVINCI_LPSC_EMAC);
lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
lpsc_on(DAVINCI_LPSC_MDIO);
lpsc_on(DAVINCI_LPSC_I2C);
lpsc_on(DAVINCI_LPSC_UART0);
lpsc_on(DAVINCI_LPSC_TIMER1);
lpsc_on(DAVINCI_LPSC_GPIO);
#if !defined(CONFIG_SYS_USE_DSPLINK)
@ -57,24 +53,11 @@ int board_init(void)
dsp_on();
#endif /* CONFIG_SYS_USE_DSPLINK */
/* Bringup UART0 out of reset */
REG(UART0_PWREMU_MGMT) = 0x0000e003;
/* Enable GIO3.3V cells used for EMAC */
REG(VDD3P3V_PWDN) = 0;
/* Enable UART0 MUX lines */
REG(PINMUX1) |= 1;
/* Enable EMAC and AEMIF pins */
REG(PINMUX0) = 0x80000c1f;
/* Enable I2C pin Mux */
REG(PINMUX1) |= (1 << 7);
/* Set the Bus Priority Register to appropriate value */
REG(VBPR) = 0x20;
davinci_enable_uart0();
davinci_enable_emac();
davinci_enable_i2c();
lpsc_on(DAVINCI_LPSC_TIMER1);
timer_init();
return(0);

Write Preview
Loading…
Cancel
Save