From 1a9283ace571384b60b931567b0a6055acec27cc Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Beh=C3=BAn?= Date: Tue, 24 Apr 2018 17:21:16 +0200 Subject: [PATCH] phy: marvell: a3700: Use (!ret) instead of (ret == 0) In U-Boot it is usually written this way. Signed-off-by: Marek Behun Reviewed-by: Stefan Roese Signed-off-by: Stefan Roese --- drivers/phy/marvell/comphy_a3700.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c index d1ccb4a..a62d672 100644 --- a/drivers/phy/marvell/comphy_a3700.c +++ b/drivers/phy/marvell/comphy_a3700.c @@ -214,7 +214,7 @@ static int comphy_pcie_power_up(u32 speed, u32 invert) rb_txdclk_pclk_en, /* value */ rb_txdclk_pclk_en, /* mask */ POLL_16B_REG); /* 16bit */ - if (ret == 0) + if (!ret) printf("Failed to lock PCIe PLL\n"); debug_exit(); @@ -283,7 +283,7 @@ static int comphy_sata_power_up(void) bs_pll_ready_tx, /* value */ bs_pll_ready_tx, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to lock SATA PLL\n"); debug_exit(); @@ -412,7 +412,7 @@ static int comphy_usb3_power_up(u32 type, u32 speed, u32 invert) rb_txdclk_pclk_en, /* value */ rb_txdclk_pclk_en, /* mask */ POLL_16B_REG); /* 16bit */ - if (ret == 0) + if (!ret) printf("Failed to lock USB3 PLL\n"); /* @@ -492,7 +492,7 @@ static int comphy_usb2_power_up(u8 usb32) rb_usb2phy_pllcal_done, /* value */ rb_usb2phy_pllcal_done, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to end USB2 PLL calibration\n"); /* Assert impedance calibration done */ @@ -500,7 +500,7 @@ static int comphy_usb2_power_up(u8 usb32) rb_usb2phy_impcal_done, /* value */ rb_usb2phy_impcal_done, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to end USB2 impedance calibration\n"); /* Assert squetch calibration done */ @@ -508,7 +508,7 @@ static int comphy_usb2_power_up(u8 usb32) rb_usb2phy_sqcal_done, /* value */ rb_usb2phy_sqcal_done, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to end USB2 unknown calibration\n"); /* Assert PLL is ready */ @@ -517,7 +517,7 @@ static int comphy_usb2_power_up(u8 usb32) rb_usb2phy_pll_ready, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to lock USB2 PLL\n"); debug_exit(); @@ -765,7 +765,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert) rb_pll_ready_tx | rb_pll_ready_rx, /* value */ rb_pll_ready_tx | rb_pll_ready_rx, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to lock PLL for SGMII PHY %d\n", lane); /* @@ -787,7 +787,7 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert) rb_rx_init_done, /* value */ rb_rx_init_done, /* mask */ POLL_32B_REG); /* 32bit */ - if (ret == 0) + if (!ret) printf("Failed to init RX of SGMII PHY %d\n", lane); debug_exit(); @@ -818,7 +818,7 @@ void comphy_dedicated_phys_init(void) if (node > 0) { if (fdtdec_get_is_enabled(blob, node)) { ret = comphy_usb2_power_up(usb32); - if (ret == 0) + if (!ret) printf("Failed to initialize UTMI PHY\n"); else debug("UTMI PHY init succeed\n"); @@ -836,7 +836,7 @@ void comphy_dedicated_phys_init(void) if (node > 0) { if (fdtdec_get_is_enabled(blob, node)) { ret = comphy_sata_power_up(); - if (ret == 0) + if (!ret) printf("Failed to initialize SATA PHY\n"); else debug("SATA PHY init succeed\n"); @@ -857,7 +857,7 @@ void comphy_dedicated_phys_init(void) if (node > 0) { if (fdtdec_get_is_enabled(blob, node)) { ret = comphy_emmc_power_up(); - if (ret == 0) + if (!ret) printf("Failed to initialize SDIO/eMMC PHY\n"); else debug("SDIO/eMMC PHY init succeed\n"); @@ -915,7 +915,7 @@ int comphy_a3700_init(struct chip_serdes_phy_config *chip_cfg, ret = 1; break; } - if (ret == 0) + if (!ret) printf("PLL is not locked - Failed to initialize lane %d\n", lane); }