arm, arm926ejs: Do cpu critical inits only for boards that require it

This patch reverts commit ca4b55800e
"arm, arm926ejs: always do cpu critical inits" since it impacts all
arm926ejs based configurations and caused problems, e.g., with
the hawkboard.

Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines
from the board configurations that need low level initialization.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>

arch/arm/cpu/arm926ejs/start.S

@@ -194,7 +194,9 @@ reset:
 	 * we do sys-critical inits only at reboot,
 	 * not when booting from ram!
 	 */
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
 	bl	cpu_init_crit
+#endif
 
 /* Set stackpointer in internal RAM to call board_init_f */
 call_board_init_f:
@@ -353,6 +355,7 @@ _dynsym_start_ofs:
  *
  *************************************************************************
  */
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
 cpu_init_crit:
 	/*
 	 * flush v4 I/D caches
@@ -371,15 +374,14 @@ cpu_init_crit:
 	orr	r0, r0, #0x00001000	/* set bit 12 (I) I-Cache */
 	mcr	p15, 0, r0, c1, c0, 0
 
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
 	/*
 	 * Go setup Memory and board specific bits prior to relocation.
 	 */
 	mov	ip, lr		/* perserve link reg across call */
 	bl	lowlevel_init	/* go setup pll,mux,memory */
 	mov	lr, ip		/* restore link */
-#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
 	mov	pc, lr		/* back to my caller */
+#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
 
 #ifndef CONFIG_SPL_BUILD
 /*

include/configs/cam_enc_4xx.h

@@ -275,12 +275,6 @@
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	0xa0000
 
-/*
- * U-Boot is a 3rd stage loader and if booting with spl, cpu setup is
- * done in board_init_f from c code.
- */
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
 /* for UBL header */
 #define CONFIG_SYS_UBL_BLOCK		(CONFIG_SYS_NAND_PAGE_SIZE)
 

include/configs/da850evm.h

@@ -42,7 +42,6 @@
 #define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
 #define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
 #define CONFIG_SYS_HZ			1000
-#define CONFIG_SKIP_LOWLEVEL_INIT
 #define CONFIG_SYS_TEXT_BASE		0xc1080000
 
 /*

include/configs/enbw_cmc.h

@@ -45,7 +45,6 @@
 #define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
 #define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
 #define CONFIG_SYS_HZ			1000
-#define CONFIG_SKIP_LOWLEVEL_INIT
 #define CONFIG_DA850_LOWLEVEL
 #define CONFIG_ARCH_CPU_INIT
 #define CONFIG_DA8XX_GPIO