diff --git a/arch/arm/dts/armada-388-clearfog.dts b/arch/arm/dts/armada-388-clearfog.dts index 1403600..16a47d5 100644 --- a/arch/arm/dts/armada-388-clearfog.dts +++ b/arch/arm/dts/armada-388-clearfog.dts @@ -81,174 +81,6 @@ soc { internal-regs { - ethernet@30000 { - mac-address = [00 50 43 02 02 02]; - phy-mode = "sgmii"; - status = "okay"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - ethernet@34000 { - mac-address = [00 50 43 02 02 03]; - managed = "in-band-status"; - phy-mode = "sgmii"; - status = "okay"; - }; - - i2c@11000 { - /* Is there anything on this? */ - clock-frequency = <100000>; - pinctrl-0 = <&i2c0_pins>; - pinctrl-names = "default"; - status = "okay"; - - /* - * PCA9655 GPIO expander, up to 1MHz clock. - * 0-CON3 CLKREQ# - * 1-CON3 PERST# - * 2-CON2 PERST# - * 3-CON3 W_DISABLE - * 4-CON2 CLKREQ# - * 5-USB3 overcurrent - * 6-USB3 power - * 7-CON2 W_DISABLE - * 8-JP4 P1 - * 9-JP4 P4 - * 10-JP4 P5 - * 11-m.2 DEVSLP - * 12-SFP_LOS - * 13-SFP_TX_FAULT - * 14-SFP_TX_DISABLE - * 15-SFP_MOD_DEF0 - */ - expander0: gpio-expander@20 { - /* - * This is how it should be: - * compatible = "onnn,pca9655", - * "nxp,pca9555"; - * but you can't do this because of - * the way I2C works. - */ - compatible = "nxp,pca9555"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x20>; - - pcie1_0_clkreq { - gpio-hog; - gpios = <0 GPIO_ACTIVE_LOW>; - input; - line-name = "pcie1.0-clkreq"; - }; - pcie1_0_w_disable { - gpio-hog; - gpios = <3 GPIO_ACTIVE_LOW>; - output-low; - line-name = "pcie1.0-w-disable"; - }; - pcie2_0_clkreq { - gpio-hog; - gpios = <4 GPIO_ACTIVE_LOW>; - input; - line-name = "pcie2.0-clkreq"; - }; - pcie2_0_w_disable { - gpio-hog; - gpios = <7 GPIO_ACTIVE_LOW>; - output-low; - line-name = "pcie2.0-w-disable"; - }; - usb3_ilimit { - gpio-hog; - gpios = <5 GPIO_ACTIVE_LOW>; - input; - line-name = "usb3-current-limit"; - }; - usb3_power { - gpio-hog; - gpios = <6 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb3-power"; - }; - m2_devslp { - gpio-hog; - gpios = <11 GPIO_ACTIVE_HIGH>; - output-low; - line-name = "m.2 devslp"; - }; - }; - - /* The MCP3021 is 100kHz clock only */ - mikrobus_adc: mcp3021@4c { - compatible = "microchip,mcp3021"; - reg = <0x4c>; - }; - - /* Also something at 0x64 */ - }; - - i2c@11100 { - /* - * Routed to SFP, mikrobus, and PCIe. - * SFP limits this to 100kHz, and requires - * an AT24C01A/02/04 with address pins tied - * low, which takes addresses 0x50 and 0x51. - * Mikrobus doesn't specify beyond an I2C - * bus being present. - * PCIe uses ARP to assign addresses, or - * 0x63-0x64. - */ - clock-frequency = <100000>; - pinctrl-0 = <&clearfog_i2c1_pins>; - pinctrl-names = "default"; - status = "okay"; - }; - - pinctrl@18000 { - clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins { - marvell,pins = "mpp46"; - marvell,function = "ref"; - }; - clearfog_dsa0_pins: clearfog-dsa0-pins { - marvell,pins = "mpp23", "mpp41"; - marvell,function = "gpio"; - }; - clearfog_i2c1_pins: i2c1-pins { - /* SFP, PCIe, mSATA, mikrobus */ - marvell,pins = "mpp26", "mpp27"; - marvell,function = "i2c1"; - }; - clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins { - marvell,pins = "mpp20"; - marvell,function = "gpio"; - }; - clearfog_spi1_cs_pins: spi1-cs-pins { - marvell,pins = "mpp55"; - marvell,function = "spi1"; - }; - mikro_pins: mikro-pins { - /* int: mpp22 rst: mpp29 */ - marvell,pins = "mpp22", "mpp29"; - marvell,function = "gpio"; - }; - mikro_spi_pins: mikro-spi-pins { - marvell,pins = "mpp43"; - marvell,function = "spi1"; - }; - mikro_uart_pins: mikro-uart-pins { - marvell,pins = "mpp24", "mpp25"; - marvell,function = "ua1"; - }; - rear_button_pins: rear-button-pins { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - }; - rtc@a3800 { /* * If the rtc doesn't work, run "date reset" @@ -297,7 +129,8 @@ status = "okay"; }; - usb3@f8000 { + usb0: usb3@f8000 { + /* CON7, USB-A port on back of device */ status = "okay"; }; }; @@ -321,72 +154,6 @@ }; }; - sfp: sfp { - compatible = "sff,sfp"; - i2c-bus = <&i2c1>; - los-gpio = <&expander0 12 GPIO_ACTIVE_HIGH>; - moddef0-gpio = <&expander0 15 GPIO_ACTIVE_LOW>; - sfp,ethernet = <ð2>; - tx-disable-gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&expander0 13 GPIO_ACTIVE_HIGH>; - }; - - dsa@0 { - compatible = "marvell,dsa"; - dsa,ethernet = <ð1>; - dsa,mii-bus = <&mdio>; - pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>; - pinctrl-names = "default"; - #address-cells = <2>; - #size-cells = <0>; - - switch@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <4 0>; - - port@0 { - reg = <0>; - label = "lan1"; - }; - - port@1 { - reg = <1>; - label = "lan2"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan4"; - }; - - port@4 { - reg = <4>; - label = "lan5"; - }; - - port@5 { - reg = <5>; - label = "cpu"; - }; - - port@6 { - /* 88E1512 external phy */ - reg = <6>; - label = "lan6"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - gpio-keys { compatible = "gpio-keys"; pinctrl-0 = <&rear_button_pins>; @@ -406,6 +173,155 @@ status = "okay"; }; +ð1 { + managed = "in-band-status"; + phy-mode = "sgmii"; + status = "okay"; +}; + +ð2 { + phy-mode = "sgmii"; + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-CON3 CLKREQ# + * 1-CON3 PERST# + * 2-CON2 PERST# + * 3-CON3 W_DISABLE + * 4-CON2 CLKREQ# + * 5-USB3 overcurrent + * 6-USB3 power + * 7-CON2 W_DISABLE + * 8-JP4 P1 + * 9-JP4 P4 + * 10-JP4 P5 + * 11-m.2 DEVSLP + * 12-SFP_LOS + * 13-SFP_TX_FAULT + * 14-SFP_TX_DISABLE + * 15-SFP_MOD_DEF0 + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + + pcie1_0_clkreq { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie1.0-clkreq"; + }; + pcie1_0_w_disable { + gpio-hog; + gpios = <3 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie1.0-w-disable"; + }; + pcie2_0_clkreq { + gpio-hog; + gpios = <4 GPIO_ACTIVE_LOW>; + input; + line-name = "pcie2.0-clkreq"; + }; + pcie2_0_w_disable { + gpio-hog; + gpios = <7 GPIO_ACTIVE_LOW>; + output-low; + line-name = "pcie2.0-w-disable"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + input; + line-name = "usb3-current-limit"; + }; + usb3_power { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb3-power"; + }; + m2_devslp { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "m.2 devslp"; + }; + }; + + mikrobus_adc: mcp3021@4c { + compatible = "microchip,mcp3021"; + reg = <0x4c>; + }; +}; + +&i2c1 { + /* + * Routed to SFP, mikrobus, and PCIe. + * SFP limits this to 100kHz, and requires + * an AT24C01A/02/04 with address pins tied + * low, which takes addresses 0x50 and 0x51. + * Mikrobus doesn't specify beyond an I2C + * bus being present. + * PCIe uses ARP to assign addresses, or + * 0x63-0x64. + */ + clock-frequency = <100000>; + pinctrl-0 = <&clearfog_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&pinctrl { + clearfog_i2c1_pins: i2c1-pins { + /* SFP, PCIe, mSATA, mikrobus */ + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + clearfog_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp55"; + marvell,function = "spi1"; + }; + mikro_pins: mikro-pins { + /* int: mpp22 rst: mpp29 */ + marvell,pins = "mpp22", "mpp29"; + marvell,function = "gpio"; + }; + mikro_spi_pins: mikro-spi-pins { + marvell,pins = "mpp43"; + marvell,function = "spi1"; + }; + mikro_uart_pins: mikro-uart-pins { + marvell,pins = "mpp24", "mpp25"; + marvell,function = "ua1"; + }; + rear_button_pins: rear-button-pins { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; +}; + /* +#define A38x_CUSTOMER_BOARD_1_MPP16_23 0x00400011 MPP18: gpio ? (pca9655 int?)