Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

powerpc/85xx: Add basic support for P1010RDB

Browse Source 
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.

P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
	32Mbyte 16bit NOR flash
	32Mbyte SLC NAND Flash
	64KB CPLD device(GPCM interface)
SPI Flash:
	128 Mbit SPI Flash memory
SD/MMC:
	connector to interface with the SD memory card
SATA:
	1 internal SATA connect to 2.5. 160G SATA2 HDD
	1 eSATA connector to rear panel
USB 2.0:
	x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
	x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
	eTSEC1: Connected to RGMII PHY VSC8641XKO
	eTSEC2: Connected to SGMII PHY VSC8221
	eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
	Two DB-9 female connectors for Field bus interface
UART:
	supports two UARTs up to 115200 bps for console
TDM:
	2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
	SPI SLIC
I2C:
	Serial EEprom
	Real time clock
	256 Kbit M24256 I2C EEPROM
PCIe:
	PCIe and mPCIe connectors.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
master
Poonam Aggrwal 14 years ago committed by Kumar Gala
parent 14aa71e660
commit 49249e137d
7 changed files with 1477 additions and 0 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 52
      board/freescale/p1010rdb/Makefile
  2. 250
      board/freescale/p1010rdb/ddr.c
  3. 35
      board/freescale/p1010rdb/law.c
  4. 330
      board/freescale/p1010rdb/p1010rdb.c
  5. 98
      board/freescale/p1010rdb/tlb.c
  6. 6
      boards.cfg
  7. 706
      include/configs/P1010RDB.h

52
board/freescale/p1010rdb/Makefile
Unescape View File

@ -0,0 +1,52 @@
#
# Copyright 2010-2011 Freescale Semiconductor, Inc.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#
include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
COBJS-y += $(BOARD).o
COBJS-y += ddr.o
COBJS-y += law.o
COBJS-y += tlb.o
SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS-y))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(call cmd_link_o_target, $(OBJS))
clean:
rm -f $(OBJS) $(SOBJS)
distclean: clean
rm -f $(LIB) core *.bak .depend
#########################################################################
# defines $(obj).depend target
include $(SRCTREE)/rules.mk
sinclude $(obj).depend
#########################################################################

250
board/freescale/p1010rdb/ddr.c
Unescape View File

@ -0,0 +1,250 @@
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
DECLARE_GLOBAL_DATA_PTR;
#ifndef CONFIG_DDR_RAW_TIMING
#define CONFIG_SYS_DRAM_SIZE 1024
fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
.ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
.ddr_data_init = CONFIG_MEM_INIT_VALUE,
.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800,
.ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
};
fsl_ddr_cfg_regs_t ddr_cfg_regs_667 = {
.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_667,
.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_667,
.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_667,
.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_667,
.ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_667,
.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_667,
.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_667,
.ddr_data_init = CONFIG_MEM_INIT_VALUE,
.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_667,
.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_667,
.ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
};
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{750, 850, &ddr_cfg_regs_800},
{607, 749, &ddr_cfg_regs_667},
{0, 0, NULL}
};
unsigned long get_sdram_size(void)
{
struct cpu_type *cpu;
phys_size_t ddr_size;
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16it DDR width */
if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E)
ddr_size = (CONFIG_SYS_DRAM_SIZE / 2);
else
ddr_size = CONFIG_SYS_DRAM_SIZE;
return ddr_size;
}
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
phys_size_t fixed_sdram(void)
{
int i;
char buf[32];
fsl_ddr_cfg_regs_t ddr_cfg_regs;
phys_size_t ddr_size;
ulong ddr_freq, ddr_freq_mhz;
struct cpu_type *cpu;
#if defined(CONFIG_SYS_RAMBOOT)
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
#endif
ddr_freq = get_ddr_freq(0);
ddr_freq_mhz = ddr_freq / 1000000;
printf("Configuring DDR for %s MT/s data rate\n",
strmhz(buf, ddr_freq));
for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
(ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings,
sizeof(ddr_cfg_regs));
break;
}
}
if (fixed_ddr_parm_0[i].max_freq == 0)
panic("Unsupported DDR data rate %s MT/s data rate\n",
strmhz(buf, ddr_freq));
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16bit DDR width */
if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) {
ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_16_BE;
ddr_cfg_regs.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS >> 1;
ddr_cfg_regs.ddr_sdram_cfg &= ~0x00180000;
ddr_cfg_regs.ddr_sdram_cfg |= 0x001080000;
}
ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
LAW_TRGT_IF_DDR_1) < 0) {
printf("ERROR setting Local Access Windows for DDR\n");
return 0;
}
return ddr_size;
}
#else /* CONFIG_DDR_RAW_TIMING */
/*
* Samsung K4B2G0846C-HCF8
* The following timing are for "downshift"
* i.e. to use CL9 part as CL7
* otherwise, tAA, tRCD, tRP will be 13500ps
* and tRC will be 49500ps
*/
dimm_params_t ddr_raw_timing = {
.n_ranks = 1,
.rank_density = 1073741824u,
.capacity = 1073741824u,
.primary_sdram_width = 32,
.ec_sdram_width = 0,
.registered_dimm = 0,
.mirrored_dimm = 0,
.n_row_addr = 15,
.n_col_addr = 10,
.n_banks_per_sdram_device = 8,
.edc_config = 0,
.burst_lengths_bitmask = 0x0c,
.tCKmin_X_ps = 1875,
.caslat_X = 0x1e << 4, /* 5,6,7,8 */
.tAA_ps = 13125,
.tWR_ps = 15000,
.tRCD_ps = 13125,
.tRRD_ps = 7500,
.tRP_ps = 13125,
.tRAS_ps = 37500,
.tRC_ps = 50625,
.tRFC_ps = 160000,
.tWTR_ps = 7500,
.tRTP_ps = 7500,
.refresh_rate_ps = 7800000,
.tFAW_ps = 37500,
};
int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
unsigned int controller_number,
unsigned int dimm_number)
{
const char dimm_model[] = "Fixed DDR on board";
if ((controller_number == 0) && (dimm_number == 0)) {
memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
}
return 0;
}
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
struct cpu_type *cpu;
int i;
popts->clk_adjust = 6;
popts->cpo_override = 0x1f;
popts->write_data_delay = 2;
popts->half_strength_driver_enable = 1;
/* Write leveling override */
popts->wrlvl_en = 1;
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
popts->wrlvl_start = 0x8;
popts->trwt_override = 1;
popts->trwt = 0;
cpu = gd->cpu;
/* P1014 and it's derivatives support max 16it DDR width */
if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E)
popts->data_bus_width = DDR_DATA_BUS_WIDTH_16;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
}
}
#endif /* CONFIG_DDR_RAW_TIMING */

35
board/freescale/p1010rdb/law.c
Unescape View File

@ -0,0 +1,35 @@
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
struct law_entry law_table[] = {
#ifndef CONFIG_SDCARD
SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_IFC),
SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC),
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
#endif
};
int num_law_entries = ARRAY_SIZE(law_table);

330
board/freescale/p1010rdb/p1010rdb.c
Unescape View File

@ -0,0 +1,330 @@
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/io.h>
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <fsl_mdio.h>
#include <tsec.h>
#include <mmc.h>
#include <netdev.h>
#include <pci.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_ifc.h>
#include <asm/fsl_pci.h>
#ifndef CONFIG_SDCARD
#include <hwconfig.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
#define GPIO4_PCIE_RESET_SET 0x08000000
#define MUX_CPLD_CAN_UART 0x00
#define MUX_CPLD_TDM 0x01
#define MUX_CPLD_SPICS0_FLASH 0x00
#define MUX_CPLD_SPICS0_SLIC 0x02
#ifndef CONFIG_SDCARD
struct cpld_data {
u8 cpld_ver; /* cpld revision */
u8 pcba_ver; /* pcb revision number */
u8 twindie_ddr3;
u8 res1[6];
u8 bank_sel; /* NOR Flash bank */
u8 res2[5];
u8 usb2_sel;
u8 res3[1];
u8 porsw_sel;
u8 tdm_can_sel;
u8 spi_cs0_sel; /* SPI CS0 SLIC/SPI Flash */
u8 por0; /* POR Options */
u8 por1; /* POR Options */
u8 por2; /* POR Options */
u8 por3; /* POR Options */
};
void cpld_show(void)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
printf("CPLD: V%x.%x PCBA: V%x.0\n",
in_8(&cpld_data->cpld_ver) & 0xF0,
in_8(&cpld_data->cpld_ver) & 0x0F,
in_8(&cpld_data->pcba_ver) & 0x0F);
#ifdef CONFIG_DEBUG
printf("twindie_ddr =%x\n",
in_8(&cpld_data->twindie_ddr3));
printf("bank_sel =%x\n",
in_8(&cpld_data->bank_sel));
printf("usb2_sel =%x\n",
in_8(&cpld_data->usb2_sel));
printf("porsw_sel =%x\n",
in_8(&cpld_data->porsw_sel));
printf("tdm_can_sel =%x\n",
in_8(&cpld_data->tdm_can_sel));
printf("tdm_can_sel =%x\n",
in_8(&cpld_data->tdm_can_sel));
printf("spi_cs0_sel =%x\n",
in_8(&cpld_data->spi_cs0_sel));
printf("bcsr0 =%x\n",
in_8(&cpld_data->bcsr0));
printf("bcsr1 =%x\n",
in_8(&cpld_data->bcsr1));
printf("bcsr2 =%x\n",
in_8(&cpld_data->bcsr2));
printf("bcsr3 =%x\n",
in_8(&cpld_data->bcsr3));
#endif
}
#endif
int board_early_init_f(void)
{
ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
#ifndef CONFIG_SDCARD
struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR;
/* Clock configuration to access CPLD using IFC(GPCM) */
setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
#endif
/*
* Reset PCIe slots via GPIO4
*/
setbits_be32(&pgpio->gpdir, GPIO4_PCIE_RESET_SET);
setbits_be32(&pgpio->gpdat, GPIO4_PCIE_RESET_SET);
return 0;
}
int board_early_init_r(void)
{
#ifndef CONFIG_SDCARD
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
/* invalidate existing TLB entry for flash */
disable_tlb(flash_esel);
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel, BOOKE_PAGESZ_16M, 1);
set_tlb(1, flashbase + 0x1000000,
CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel+1, BOOKE_PAGESZ_16M, 1);
#endif
return 0;
}
#ifdef CONFIG_PCI
void pci_init_board(void)
{
fsl_pcie_init_board(0);
}
#endif /* ifdef CONFIG_PCI */
int checkboard(void)
{
struct cpu_type *cpu;
cpu = gd->cpu;
printf("Board: %sRDB ", cpu->name);
#ifdef CONFIG_PHYS_64BIT
puts("(36-bit addrmap)");
#endif
puts("\n");
return 0;
}
#ifdef CONFIG_TSEC_ENET
int board_eth_init(bd_t *bis)
{
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[4];
struct cpu_type *cpu;
int num = 0;
cpu = gd->cpu;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
num++;
#endif
#ifdef CONFIG_TSEC3
/* P1014 and it's derivatives do not support eTSEC3 */
if (cpu->soc_ver != SVR_P1014 && cpu->soc_ver != SVR_P1014_E) {
SET_STD_TSEC_INFO(tsec_info[num], 3);
num++;
}
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bis, &mdio_info);
tsec_eth_init(bis, tsec_info, num);
return pci_eth_init(bis);
}
#endif
#if defined(CONFIG_OF_BOARD_SETUP)
void fdt_del_flexcan(void *blob)
{
int nodeoff = 0;
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
"fsl,flexcan-v1.0")) >= 0) {
fdt_del_node(blob, nodeoff);
}
}
void fdt_del_spi_flash(void *blob)
{
int nodeoff = 0;
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
"spansion,s25sl12801")) >= 0) {
fdt_del_node(blob, nodeoff);
}
}
void fdt_del_spi_slic(void *blob)
{
int nodeoff = 0;
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
"zarlink,le88266")) >= 0) {
fdt_del_node(blob, nodeoff);
}
}
void fdt_del_tdm(void *blob)
{
int nodeoff = 0;
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
"fsl,starlite-tdm")) >= 0) {
fdt_del_node(blob, nodeoff);
}
}
void ft_board_setup(void *blob, bd_t *bd)
{
phys_addr_t base;
phys_size_t size;
struct cpu_type *cpu;
cpu = gd->cpu;
ft_cpu_setup(blob, bd);
base = getenv_bootm_low();
size = getenv_bootm_size();
#if defined(CONFIG_PCI)
FT_FSL_PCI_SETUP;
#endif
fdt_fixup_memory(blob, (u64)base, (u64)size);
fdt_fixup_dr_usb(blob, bd);
/* P1014 and it's derivatives don't support CAN and eTSEC3 */
if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) {
fdt_del_flexcan(blob);
fdt_del_node_and_alias(blob, "ethernet2");
}
#ifndef CONFIG_SDCARD
if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) {
printf("fdt CAN");
fdt_del_tdm(blob);
fdt_del_spi_slic(blob);
}
#ifndef CONFIG_SPIFLASH
else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
printf("fdt TDM");
fdt_del_flexcan(blob);
fdt_del_spi_flash(blob);
}
#endif
#endif
}
#endif
#ifndef CONFIG_SDCARD
int misc_init_r(void)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) {
clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN1_TDM |
MPC85xx_PMUXCR_CAN1_UART |
MPC85xx_PMUXCR_CAN2_TDM |
MPC85xx_PMUXCR_CAN2_UART);
out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART);
}
#ifndef CONFIG_SPIFLASH
if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) {
printf("TDM");
clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART |
MPC85xx_PMUXCR_CAN1_UART);
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM |
MPC85xx_PMUXCR_CAN1_TDM);
clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO);
setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM);
out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM);
out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC);
}
#endif
return 0;
}
#endif

98
board/freescale/p1010rdb/tlb.c
Unescape View File

@ -0,0 +1,98 @@
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/mmu.h>
struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
/* TLB 1 */
/* *I*** - Covers boot page */
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 0, BOOKE_PAGESZ_4K, 1),
/* *I*G* - CCSRBAR */
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 1, BOOKE_PAGESZ_1M, 1),
#ifndef CONFIG_NAND_SPL
#ifndef CONFIG_SDCARD
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_16M, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000,
CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000,
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 3, BOOKE_PAGESZ_16M, 1),
#endif
#ifdef CONFIG_PCI
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 4, BOOKE_PAGESZ_1G, 1),
/* *I*G* - PCI I/O */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 5, BOOKE_PAGESZ_256K, 1),
#endif
#endif
#ifndef CONFIG_SDCARD
/* *I*G - Board CPLD */
SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_256K, 1),
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_1M, 1),
#endif
#if defined(CONFIG_SYS_RAMBOOT)
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 8, BOOKE_PAGESZ_1G, 1)
#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);

6
boards.cfg
Unescape View File

@ -567,6 +567,12 @@ MPC8569MDS_NAND powerpc mpc85xx mpc8569mds freesca
MPC8572DS powerpc mpc85xx mpc8572ds freescale - MPC8572DS
MPC8572DS_36BIT powerpc mpc85xx mpc8572ds freescale - MPC8572DS:36BIT
MPC8572DS_NAND powerpc mpc85xx mpc8572ds freescale - MPC8572DS:NAND
P1010RDB_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB
P1010RDB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT
P1010RDB_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SDCARD
P1010RDB_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SPIFLASH
P1010RDB_36BIT_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SDCARD
P1010RDB_36BIT_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SPIFLASH
P1011RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB
P1011RDB_36BIT powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT
P1011RDB_36BIT_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT,SDCARD

706
include/configs/P1010RDB.h
Unescape View File

@ -0,0 +1,706 @@
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* P010 RDB board configuration file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#ifdef CONFIG_36BIT
#define CONFIG_PHYS_64BIT
#endif
#ifdef CONFIG_P1010RDB
#define CONFIG_P1010
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD
#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff80000
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/* High Level Configuration Options */
#define CONFIG_BOOKE /* BOOKE */
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_MPC85xx
#define CONFIG_FSL_IFC /* Enable IFC Support */
#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
#define CONFIG_PCI /* Enable PCI/PCIE */
#if defined(CONFIG_PCI)
#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
#define CONFIG_E1000 /* E1000 pci Ethernet card*/
/*
* PCI Windows
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, Slot 1, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME "mini PCIe Slot"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#endif
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_NAME "PCIe Slot"
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#else
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
#else
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
#endif
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#endif
#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_TSEC_ENET
#define CONFIG_ENV_OVERWRITE
#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1010 RDB */
#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */
#ifndef CONFIG_SDCARD
#define CONFIG_MISC_INIT_R
#endif
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP 1
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#endif
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* DDR Setup */
#define CONFIG_FSL_DDR3
#define CONFIG_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#ifndef __ASSEMBLY__
extern unsigned long get_sdram_size(void);
#endif
#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
/* DDR3 Controller Settings */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
#define CONFIG_SYS_DDR_RCW_1 0x00000000
#define CONFIG_SYS_DDR_RCW_2 0x00000000
#define CONFIG_SYS_DDR_CONTROL 0x470C0000 /* Type = DDR3 */
#define CONFIG_SYS_DDR_CONTROL_2 0x04401010
#define CONFIG_SYS_DDR_TIMING_4 0x00000001
#define CONFIG_SYS_DDR_TIMING_5 0x03402400
#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000
#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004
#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4644
#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF
#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
#define CONFIG_SYS_DDR_MODE_1_800 0x40461520
#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100
#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608
/* settings for DDR3 at 667MT/s */
#define CONFIG_SYS_DDR_TIMING_3_667 0x00010000
#define CONFIG_SYS_DDR_TIMING_0_667 0x00110004
#define CONFIG_SYS_DDR_TIMING_1_667 0x5d59e544
#define CONFIG_SYS_DDR_TIMING_2_667 0x0FA890CD
#define CONFIG_SYS_DDR_CLK_CTRL_667 0x03000000
#define CONFIG_SYS_DDR_MODE_1_667 0x00441210
#define CONFIG_SYS_DDR_MODE_2_667 0x00000000
#define CONFIG_SYS_DDR_INTERVAL_667 0x0a280000
#define CONFIG_SYS_DDR_WRLVL_CONTROL_667 0x8675F608
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/*
* Memory map
*
* 0x0000_0000 0x3fff_ffff DDR 1G cacheable
* 0x8000_0000 0xbfff_ffff PCI Express Mem 1.5G non-cacheable
* 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
*
* Localbus non-cacheable
* 0xff80_0000 0xff8f_ffff NAND Flash 1M non-cacheable
* 0xffb0_0000 0xffbf_ffff Board CPLD 1M non-cacheable
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
/* In case of SD card boot, IFC interface is not available because of muxing */
#ifdef CONFIG_SDCARD
#define CONFIG_SYS_NO_FLASH
#else
/*
* IFC Definitions
*/
/* NOR Flash on IFC */
#define CONFIG_SYS_FLASH_BASE 0xee000000
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#else
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(32*1024*1024)
#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(7)
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_FTIM0 FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TEAHC(0x5)
#define CONFIG_SYS_NOR_FTIM1 FTIM1_NOR_TACO(0x1e) | \
FTIM1_NOR_TRAD_NOR(0x0f)
#define CONFIG_SYS_NOR_FTIM2 FTIM2_NOR_TCS(0x4) | \
FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWP(0x1c)
#define CONFIG_SYS_NOR_FTIM3 0x0
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/* CFI for NOR Flash */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE 0xff800000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#endif
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_NAND \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_2 /* RAL = 2 Bytes */ \
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
/* NAND Flash Timing Params */
#define CONFIG_SYS_NAND_FTIM0 FTIM0_NAND_TCCST(0x01) | \
FTIM0_NAND_TWP(0x0C) | \
FTIM0_NAND_TWCHT(0x04) | \
FTIM0_NAND_TWH(0x05)
#define CONFIG_SYS_NAND_FTIM1 FTIM1_NAND_TADLE(0x1d) | \
FTIM1_NAND_TWBE(0x1d) | \
FTIM1_NAND_TRR(0x07) | \
FTIM1_NAND_TRP(0x0c)
#define CONFIG_SYS_NAND_FTIM2 FTIM2_NAND_TRAD(0x0c) | \
FTIM2_NAND_TREH(0x05) | \
FTIM2_NAND_TWHRE(0x0f)
#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
#define CONFIG_SYS_NAND_DDR_LAW 11
/* Set up IFC registers for boot location NOR/NAND */
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
/* CPLD on IFC */
#define CONFIG_SYS_CPLD_BASE 0xffb00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CPLD_BASE_PHYS 0xfffb00000ull
#else
#define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
#endif
#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR3 0x0
/* CPLD Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
FTIM0_GPCM_TEADC(0x0e) | \
FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
FTIM1_GPCM_TRAD(0x1f))
#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
FTIM2_GPCM_TCH(0x0) | \
FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3 0x0
#endif /* CONFIG_SDCARD */
#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \
defined(CONFIG_RAMBOOT_NAND)
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
- GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SERIAL_MULTI /* Enable both serial ports */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
* Pass open firmware flat tree
*/
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
/* I2C EEPROM */
#undef CONFIG_ID_EEPROM
/* enable read and write access to EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* RTC */
#define CONFIG_RTC_PT7C4338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_CMD_I2C
/*
* SPI interface will not be available in case of NAND boot SPI CS0 will be
* used for SLIC
*/
/* eSPI - Enhanced SPI */
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI
#endif
#define CONFIG_MII /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC2"
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
#define TSEC1_PHY_ADDR 1
#define TSEC2_PHY_ADDR 0
#define TSEC3_PHY_ADDR 2
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC1"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
/* TBI PHY configuration for SGMII mode */
#define CONFIG_TSEC_TBICR_SETTINGS ( \
TBICR_PHY_RESET \
| TBICR_ANEG_ENABLE \
| TBICR_FULL_DUPLEX \
| TBICR_SPEED1_SET \
)
#endif /* CONFIG_TSEC_ENET */
/* SATA */
#define CONFIG_FSL_SATA
#define CONFIG_LIBATA
#ifdef CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#define CONFIG_CMD_SATA
#define CONFIG_LBA48
#endif /* #ifdef CONFIG_FSL_SATA */
/* SD interface will only be available in case of SD boot */
#ifdef CONFIG_SDCARD
#define CONFIG_MMC
#define CONFIG_DEF_HWCONFIG esdhc
#endif
#ifdef CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#endif
#endif
/*
* Environment
*/
#if defined(CONFIG_SYS_RAMBOOT)
#if defined(CONFIG_RAMBOOT_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_ENV_SPI_MODE 0
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#else
#define CONFIG_ENV_IS_IN_FLASH
#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
#define CONFIG_ENV_ADDR 0xfff80000
#else
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#endif
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_REGINFO
#undef CONFIG_WATCHDOG /* watchdog disabled */
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
|| defined(CONFIG_FSL_SATA)
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif
#define CONFIG_HOSTNAME P1010RDB
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=" MK_STR(CONFIG_DEF_HWCONFIG) "\0" \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"loadaddr=1000000\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=p1010rdb.dtb\0" \
"bdev=sda1\0" \
"hwconfig=usb1:dr_mode=host,phy_type=utmi\0" \
"othbootargs=ramdisk_size=600000\0" \
"usbfatboot=setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs; " \
"usb start;" \
"fatload usb 0:2 $loadaddr $bootfile;" \
"fatload usb 0:2 $fdtaddr $fdtfile;" \
"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
"usbext2boot=setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs; " \
"usb start;" \
"ext2load usb 0:4 $loadaddr $bootfile;" \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs; " \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
#endif /* __CONFIG_H */
Write Preview
Loading…
Cancel
Save