ColdFire: Multiple fixes for M5282EVB

Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>

board/freescale/m5282evb/m5282evb.c

@@ -51,6 +51,7 @@ phys_size_t initdram (int board_type)
 		MCFSDRAMC_DCR = (0
 			| MCFSDRAMC_DCR_RTIM_6
 			| MCFSDRAMC_DCR_RC((15 * dramclk)>>4));
+		asm("nop");
 
 		/* Initialize DACR0 */
 		MCFSDRAMC_DACR0 = (0
@@ -58,14 +59,17 @@ phys_size_t initdram (int board_type)
 			| MCFSDRAMC_DACR_CASL(1)
 			| MCFSDRAMC_DACR_CBM(3)
 			| MCFSDRAMC_DACR_PS_32);
+		asm("nop");
 
 		/* Initialize DMR0 */
 		MCFSDRAMC_DMR0 = (0
 			| ((dramsize - 1) & 0xFFFC0000)
 			| MCFSDRAMC_DMR_V);
+		asm("nop");
 
 		/* Set IP (bit 3) in DACR */
 		MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_IP;
+		asm("nop");
 
 		/* Wait 30ns to allow banks to precharge */
 		for (i = 0; i < 5; i++) {
@@ -74,9 +78,11 @@ phys_size_t initdram (int board_type)
 
 		/* Write to this block to initiate precharge */
 		*(u32 *)(CFG_SDRAM_BASE) = 0xA5A59696;
+		asm("nop");
 
 		/* Set RE (bit 15) in DACR */
 		MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_RE;
+		asm("nop");
 
 		/* Wait for at least 8 auto refresh cycles to occur */
 		for (i = 0; i < 2000; i++) {
@@ -85,6 +91,7 @@ phys_size_t initdram (int board_type)
 
 		/* Finish the configuration by issuing the IMRS. */
 		MCFSDRAMC_DACR0 |= MCFSDRAMC_DACR_IMRS;
+		asm("nop");
 
 		/* Write to the SDRAM Mode Register */
 		*(u32 *)(CFG_SDRAM_BASE + 0x400) = 0xA5A59696;

board/freescale/m5282evb/u-boot.lds

@@ -60,9 +60,8 @@ SECTIONS
     lib_generic/string.o	(.text)
     lib_generic/vsprintf.o	(.text)
     lib_generic/crc32.o	(.text)
-    lib_generic/zlib.o	(.text)
 
-/*    . = env_offset; */
+    . = env_offset;
     common/environment.o(.text)
 
     *(.text)

cpu/mcf52x2/cpu_init.c

@@ -442,7 +442,7 @@ void cpu_init_f(void)
 	MCFCSM_CSMR0 = MCFCSM_CSMR_BAM(CFG_CS0_SIZE - 1) | MCFCSM_CSMR_V;
 #endif
 #else
-#waring "Chip Select 0 are not initialized/used"
+#warning "Chip Select 0 are not initialized/used"
 #endif
 
 #if defined(CFG_CS1_BASE) & defined(CFG_CS1_SIZE) & \

cpu/mcf52x2/start.S

@@ -166,7 +166,7 @@ _after_flashbar_copy:
 #else
 	/* Setup code to initialize FLASHBAR, if start from external Memory */
 	move.l	#(CFG_INT_FLASH_BASE + CFG_INT_FLASH_ENABLE), %d0
-	movec	%d0, %RAMBAR1
+	movec	%d0, %FLASHBAR
 #endif /* (TEXT_BASE == CFG_INT_FLASH_BASE) */
 
 #endif

include/configs/M5282EVB.h

@@ -104,7 +104,7 @@
 #	define CONFIG_OVERWRITE_ETHADDR_ONCE
 #endif				/* CONFIG_MCFFEC */
 
-#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_HOSTNAME		M5282EVB
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"netdev=eth0\0"				\
 	"loadaddr=10000\0"			\
@@ -134,7 +134,7 @@
 #define CFG_MEMTEST_START	0x400
 #define CFG_MEMTEST_END		0x380000
 
-#define CFG_HZ			1000000
+#define CFG_HZ			1000
 #define	CFG_CLK			64000000
 
 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */