Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'

Conflicts:
	arch/arm/include/asm/arch-zynq/hardware.h

The conflict above was trivial and solved during merge.

arch/arm/cpu/armv7/zynq/Makefile

@@ -14,6 +14,7 @@ LIB	= $(obj)lib$(SOC).o
 
 COBJS-y	:= timer.o
 COBJS-y	+= cpu.o
+COBJS-y	+= ddrc.o
 COBJS-y	+= slcr.o
 
 COBJS	:= $(COBJS-y)

arch/arm/cpu/armv7/zynq/ddrc.c

@@ -0,0 +1,50 @@
+/*
+ * Copyright (C) 2012 - 2013 Michal Simek <monstr@monstr.eu>
+ * Copyright (C) 2012 - 2013 Xilinx, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Control regsiter bitfield definitions */
+#define ZYNQ_DDRC_CTRLREG_BUSWIDTH_MASK		0xC
+#define ZYNQ_DDRC_CTRLREG_BUSWIDTH_SHIFT	2
+#define ZYNQ_DDRC_CTRLREG_BUSWIDTH_16BIT	1
+
+/* ECC scrub regsiter definitions */
+#define ZYNQ_DDRC_ECC_SCRUBREG_ECC_MODE_MASK	0x7
+#define ZYNQ_DDRC_ECC_SCRUBREG_ECCMODE_SECDED	0x4
+
+void zynq_ddrc_init(void)
+{
+	u32 width, ecctype;
+
+	width = readl(&ddrc_base->ddrc_ctrl);
+	width = (width & ZYNQ_DDRC_CTRLREG_BUSWIDTH_MASK) >>
+					ZYNQ_DDRC_CTRLREG_BUSWIDTH_SHIFT;
+	ecctype = (readl(&ddrc_base->ecc_scrub) &
+		ZYNQ_DDRC_ECC_SCRUBREG_ECC_MODE_MASK);
+
+	/* ECC is enabled when memory is in 16bit mode and it is enabled */
+	if ((ecctype == ZYNQ_DDRC_ECC_SCRUBREG_ECCMODE_SECDED) &&
+	    (width == ZYNQ_DDRC_CTRLREG_BUSWIDTH_16BIT)) {
+		puts("Memory: ECC enabled\n");
+		/*
+		 * Clear the first 1MB because it is not initialized from
+		 * first stage bootloader. To get ECC to work all memory has
+		 * been initialized by writing any value.
+		 */
+		memset(0, 0, 1 * 1024 * 1024);
+	} else {
+		puts("Memory: ECC disabled\n");
+	}
+
+	if (width == ZYNQ_DDRC_CTRLREG_BUSWIDTH_16BIT)
+		gd->ram_size /= 2;
+}

arch/arm/cpu/armv7/zynq/slcr.c

@@ -70,7 +70,7 @@ void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk)
 		/* Configure GEM_RCLK_CTRL */
 		writel(rclk, &slcr_base->gem0_rclk_ctrl);
 	}
-
+	udelay(100000);
 out:
 	zynq_slcr_lock();
 }

arch/arm/include/asm/arch-zynq/hardware.h

@@ -19,6 +19,7 @@
 #define ZYNQ_I2C_BASEADDR1		0xE0005000
 #define ZYNQ_SPI_BASEADDR0		0xE0006000
 #define ZYNQ_SPI_BASEADDR1		0xE0007000
+#define ZYNQ_DDRC_BASEADDR		0xF8006000
 
 /* Reflect slcr offsets */
 struct slcr_regs {
@@ -86,4 +87,11 @@ struct scu_regs {
 
 #define scu_base ((struct scu_regs *)ZYNQ_SCU_BASEADDR)
 
+struct ddrc_regs {
+	u32 ddrc_ctrl; /* 0x0 */
+	u32 reserved[60];
+	u32 ecc_scrub; /* 0xF4 */
+};
+#define ddrc_base ((struct ddrc_regs *)ZYNQ_DDRC_BASEADDR)
+
 #endif /* _ASM_ARCH_HARDWARE_H */

arch/arm/include/asm/arch-zynq/sys_proto.h

@@ -14,6 +14,7 @@ extern void zynq_slcr_gem_clk_setup(u32 gem_id, u32 rclk, u32 clk);
 extern void zynq_slcr_devcfg_disable(void);
 extern void zynq_slcr_devcfg_enable(void);
 extern u32 zynq_slcr_get_idcode(void);
+extern void zynq_ddrc_init(void);
 
 /* Driver extern functions */
 extern int zynq_sdhci_init(u32 regbase);

board/xilinx/zynq/board.c

@@ -65,6 +65,23 @@ int board_eth_init(bd_t *bis)
 {
 	u32 ret = 0;
 
+#ifdef CONFIG_XILINX_AXIEMAC
+	ret |= xilinx_axiemac_initialize(bis, XILINX_AXIEMAC_BASEADDR,
+						XILINX_AXIDMA_BASEADDR);
+#endif
+#ifdef CONFIG_XILINX_EMACLITE
+	u32 txpp = 0;
+	u32 rxpp = 0;
+# ifdef CONFIG_XILINX_EMACLITE_TX_PING_PONG
+	txpp = 1;
+# endif
+# ifdef CONFIG_XILINX_EMACLITE_RX_PING_PONG
+	rxpp = 1;
+# endif
+	ret |= xilinx_emaclite_initialize(bis, XILINX_EMACLITE_BASEADDR,
+			txpp, rxpp);
+#endif
+
 #if defined(CONFIG_ZYNQ_GEM)
 # if defined(CONFIG_ZYNQ_GEM0)
 	ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR0,
@@ -100,5 +117,7 @@ int dram_init(void)
 {
 	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
 
+	zynq_ddrc_init();
+
 	return 0;
 }