board: sama5d2_xplained: Move config options to defconfigs

Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>

board/atmel/sama5d2_xplained/sama5d2_xplained.c

@@ -25,10 +25,12 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifndef CONFIG_DM_SPI
 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
 {
 	return bus == 0 && cs == 0;
 }
+#endif
 
 void spi_cs_activate(struct spi_slave *slave)
 {

configs/sama5d2_xplained_mmc_defconfig

@@ -8,6 +8,9 @@ CONFIG_SPL_FAT_SUPPORT=y
 CONFIG_SPL_LIBDISK_SUPPORT=y
 CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained"
 CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
 CONFIG_BOOTDELAY=3
@@ -21,14 +24,40 @@ CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_MMC=y
 CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_FPGA is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_BLK=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_AT91=y
+CONFIG_DM_MMC=y
+CONFIG_DM_MMC_OPS=y
+CONFIG_ATMEL_SDHCI=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
 CONFIG_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_ATMEL_USBA=y
-CONFIG_OF_LIBFDT=y

configs/sama5d2_xplained_spiflash_defconfig

@@ -7,6 +7,9 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained"
 CONFIG_FIT=y
 CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_SERIALFLASH"
 CONFIG_BOOTDELAY=3
@@ -20,14 +23,40 @@ CONFIG_CMD_BOOTZ=y
 # CONFIG_CMD_FLASH is not set
 CONFIG_CMD_MMC=y
 CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_FPGA is not set
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_PING=y
 CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_BLK=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_AT91=y
+CONFIG_DM_MMC=y
+CONFIG_DM_MMC_OPS=y
+CONFIG_ATMEL_SDHCI=y
+CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
 CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_ATMEL_USBA=y
-CONFIG_OF_LIBFDT=y

include/configs/sama5d2_xplained.h

@@ -15,11 +15,6 @@
 
 #include "at91-sama5_common.h"
 
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE		ATMEL_BASE_UART1
-#define CONFIG_USART_ID			ATMEL_ID_UART1
-
 /* SDRAM */
 #define CONFIG_NR_DRAM_BANKS		1
 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
@@ -34,14 +29,8 @@
 
 #define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
 
-#undef CONFIG_AT91_GPIO
-#define CONFIG_ATMEL_PIO4
-
 /* SerialFlash */
 #ifdef CONFIG_CMD_SF
-#define CONFIG_ATMEL_SPI
-#define CONFIG_ATMEL_SPI0
-#define CONFIG_SPI_FLASH_ATMEL
 #define CONFIG_SF_DEFAULT_BUS		0
 #define CONFIG_SF_DEFAULT_CS		0
 #define CONFIG_SF_DEFAULT_SPEED		30000000
@@ -51,23 +40,9 @@
 #undef CONFIG_CMD_NAND
 
 /* MMC */
-
 #ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_SDHCI
-#define CONFIG_ATMEL_SDHCI
-#define CONFIG_ATMEL_SDHCI0
-#define CONFIG_ATMEL_SDHCI1
-#define CONFIG_SUPPORT_EMMC_BOOT
-#endif
-
-/* USB */
-
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
 #endif
 
 /* USB device */