warp7: Add PMIC support

Add PMIC support. Tested by command "pmic PFUZE3000 dump".

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>

board/warp7/warp7.c

@@ -11,12 +11,17 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/gpio.h>
 #include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
 #include <asm/io.h>
 #include <common.h>
 #include <fsl_esdhc.h>
+#include <i2c.h>
 #include <mmc.h>
 #include <asm/arch/crm_regs.h>
 #include <usb.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../freescale/common/pfuze.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -25,6 +30,26 @@ DECLARE_GLOBAL_DATA_PTR;
 #define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW |	\
 			PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
 
+#define I2C_PAD_CTRL	(PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SCL__GPIO4_IO8 | PC,
+		.gp = IMX_GPIO_NR(4, 8),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = MX7D_PAD_I2C1_SDA__GPIO4_IO9 | PC,
+		.gp = IMX_GPIO_NR(4, 9),
+	},
+};
+#endif
+
 int dram_init(void)
 {
 	gd->ram_size = PHYS_SDRAM_SIZE;
@@ -85,11 +110,43 @@ int board_early_init_f(void)
 	return 0;
 }
 
+#ifdef CONFIG_POWER
+#define I2C_PMIC       0
+static struct pmic *pfuze;
+int power_init_board(void)
+{
+	int ret;
+	unsigned int reg, rev_id;
+
+	ret = power_pfuze3000_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	pfuze = pmic_get("PFUZE3000");
+	ret = pmic_probe(pfuze);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(pfuze, PFUZE3000_DEVICEID, &reg);
+	pmic_reg_read(pfuze, PFUZE3000_REVID, &rev_id);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, 0x1);
+
+	return 0;
+}
+#endif
+
 int board_init(void)
 {
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+	#ifdef CONFIG_SYS_I2C_MXC
+		setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	#endif
+
 	return 0;
 }
 

include/configs/warp7.h

@@ -103,6 +103,18 @@
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
+/* I2C configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+
 /* FLASH and environment organization */
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENV_SIZE			SZ_8K