sun7i: Add new Bananapro board / defconfig

Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

board/sunxi/Kconfig

@@ -96,6 +96,10 @@ config TARGET_BANANAPI
 	bool "BANANAPI"
 	depends on MACH_SUN7I
 
+config TARGET_BANANAPRO
+	bool "BANANAPRO"
+	depends on MACH_SUN7I
+
 config TARGET_COLOMBUS
 	bool "COLOMBUS"
 	depends on MACH_SUN6I

board/sunxi/MAINTAINERS

@@ -23,6 +23,7 @@ F:	configs/Mele_M9_defconfig
 F:	include/configs/sun7i.h
 F:	configs/A20-OLinuXino_MICRO_defconfig
 F:	configs/Bananapi_defconfig
+F:	configs/Bananapro_defconfig
 F:	configs/i12-tvbox_defconfig
 F:	configs/Linksprite_pcDuino3_defconfig
 F:	configs/Linksprite_pcDuino3_fdt_defconfig

board/sunxi/Makefile

@@ -22,6 +22,7 @@ obj-$(CONFIG_TARGET_A20_OLINUXINO_M)	+= dram_sun7i_384_1024_iow16.o
 obj-$(CONFIG_TARGET_AUXTEK_T004)	+= dram_a10s_olinuxino_m.o
 obj-$(CONFIG_TARGET_BA10_TV_BOX)	+= dram_sun4i_384_1024_iow8.o
 obj-$(CONFIG_TARGET_BANANAPI)		+= dram_bananapi.o
+obj-$(CONFIG_TARGET_BANANAPRO)		+= dram_bananapi.o
 obj-$(CONFIG_TARGET_CUBIEBOARD)		+= dram_cubieboard.o
 obj-$(CONFIG_TARGET_CUBIEBOARD2)	+= dram_cubieboard2.o
 obj-$(CONFIG_TARGET_CUBIETRUCK)		+= dram_cubietruck.o

board/sunxi/gmac.c

@@ -34,7 +34,7 @@ int sunxi_gmac_initialize(bd_t *bis)
 	 * need to set bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain"
 	 * of the GMAC clk register to 3.
 	 */
-#ifdef CONFIG_TARGET_BANANAPI
+#if defined CONFIG_TARGET_BANANAPI || defined CONFIG_TARGET_BANANAPRO
 	setbits_le32(&ccm->gmac_clk_cfg, 0x3 << 10);
 #endif
 

configs/Bananapro_defconfig

@@ -0,0 +1,9 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
+CONFIG_FDTFILE="sun7i-a20-bananapro.dtb"
+CONFIG_USB1_VBUS_PIN="PH0"
+CONFIG_USB2_VBUS_PIN="PH1"
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_SUNXI=y
++S:CONFIG_MACH_SUN7I=y
++S:CONFIG_TARGET_BANANAPRO=y