diff --git a/arch/arm/cpu/arm926ejs/mx25/generic.c b/arch/arm/cpu/arm926ejs/mx25/generic.c
index 0b1a8f4..5d9bc6c 100644
--- a/arch/arm/cpu/arm926ejs/mx25/generic.c
+++ b/arch/arm/cpu/arm926ejs/mx25/generic.c
@@ -58,6 +58,14 @@ static ulong imx_get_mpllclk(void)
 	return imx_decode_pll(readl(&ccm->mpctl), fref);
 }
 
+static ulong imx_get_upllclk(void)
+{
+	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
+	ulong fref = MXC_HCLK;
+
+	return imx_decode_pll(readl(&ccm->upctl), fref);
+}
+
 static ulong imx_get_armclk(void)
 {
 	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
@@ -95,7 +103,8 @@ static ulong imx_get_ipgclk(void)
 static ulong imx_get_perclk(int clk)
 {
 	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
-	ulong fref = imx_get_ahbclk();
+	ulong fref = readl(&ccm->mcr) & (1 << clk) ? imx_get_upllclk() :
+						     imx_get_ahbclk();
 	ulong div;
 
 	div = readl(&ccm->pcdr[CCM_PERCLK_REG(clk)]);
@@ -104,6 +113,25 @@ static ulong imx_get_perclk(int clk)
 	return fref / div;
 }
 
+int imx_set_perclk(enum mxc_clock clk, bool from_upll, unsigned int freq)
+{
+	struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE;
+	ulong fref = from_upll ? imx_get_upllclk() : imx_get_ahbclk();
+	ulong div = (fref + freq - 1) / freq;
+
+	if (clk > MXC_UART_CLK || !div || --div > CCM_PERCLK_MASK)
+		return -EINVAL;
+
+	clrsetbits_le32(&ccm->pcdr[CCM_PERCLK_REG(clk)],
+			CCM_PERCLK_MASK << CCM_PERCLK_SHIFT(clk),
+			div << CCM_PERCLK_SHIFT(clk));
+	if (from_upll)
+		setbits_le32(&ccm->mcr, 1 << clk);
+	else
+		clrbits_le32(&ccm->mcr, 1 << clk);
+	return 0;
+}
+
 unsigned int mxc_get_clock(enum mxc_clock clk)
 {
 	if (clk >= MXC_CLK_NUM)
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index dd94797..2bedbdb 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -158,7 +158,7 @@ u32 get_cpu_speed_grade_hz(void)
  * OCOTP_MEM0[7:6] (see Fusemap Description Table offset 0x480)
  * defines a 2-bit Temperature Grade
  *
- * return temperature grade and min/max temperature in celcius
+ * return temperature grade and min/max temperature in Celsius
  */
 #define OCOTP_MEM0_TEMP_SHIFT          6
 
diff --git a/arch/arm/cpu/armv7/mx7/Kconfig b/arch/arm/cpu/armv7/mx7/Kconfig
index 80c1290..aea8526 100644
--- a/arch/arm/cpu/armv7/mx7/Kconfig
+++ b/arch/arm/cpu/armv7/mx7/Kconfig
@@ -25,6 +25,13 @@ config TARGET_MX7DSABRESD
 	select DM
 	select DM_THERMAL
 
+config TARGET_PICO_IMX7D
+	bool "pico-imx7d"
+	select BOARD_LATE_INIT
+	select MX7D
+	select DM
+	select DM_THERMAL
+
 config TARGET_WARP7
 	bool "warp7"
 	select BOARD_LATE_INIT
@@ -45,6 +52,7 @@ config SYS_SOC
 	default "mx7"
 
 source "board/freescale/mx7dsabresd/Kconfig"
+source "board/technexion/pico-imx7d/Kconfig"
 source "board/toradex/colibri_imx7/Kconfig"
 source "board/warp7/Kconfig"
 
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 40fe813..74bdd24 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -275,6 +275,9 @@ u32 get_ahb_clk(void)
 
 void arch_preboot_os(void)
 {
+#if defined(CONFIG_PCIE_IMX)
+	imx_pcie_remove();
+#endif
 #if defined(CONFIG_CMD_SATA)
 	sata_stop();
 #if defined(CONFIG_MX6)
diff --git a/arch/arm/include/asm/arch-mx25/clock.h b/arch/arm/include/asm/arch-mx25/clock.h
index 9fdaa9d..7753caf 100644
--- a/arch/arm/include/asm/arch-mx25/clock.h
+++ b/arch/arm/include/asm/arch-mx25/clock.h
@@ -51,6 +51,7 @@ enum mxc_clock {
 	MXC_CLK_NUM
 };
 
+int imx_set_perclk(enum mxc_clock clk, bool from_upll, unsigned int freq);
 unsigned int mxc_get_clock(enum mxc_clock clk);
 
 #define imx_get_uartclk()	mxc_get_clock(MXC_UART_CLK)
diff --git a/board/engicam/common/board.c b/board/engicam/common/board.c
index af4ef28..e3bb569 100644
--- a/board/engicam/common/board.c
+++ b/board/engicam/common/board.c
@@ -53,6 +53,11 @@ int board_late_init(void)
 		break;
 	}
 
+	if (is_mx6ul())
+		setenv("console", "ttymxc0");
+	else
+		setenv("console", "ttymxc3");
+
 	setenv_fdt_file();
 
 	return 0;
diff --git a/board/engicam/geam6ul/Kconfig b/board/engicam/geam6ul/Kconfig
index 8753d15..7f4023e 100644
--- a/board/engicam/geam6ul/Kconfig
+++ b/board/engicam/geam6ul/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
 	default "engicam"
 
 config SYS_CONFIG_NAME
-	default "imx6ul_geam"
+	default "imx6-engicam"
 
 endif
diff --git a/board/engicam/icorem6/Kconfig b/board/engicam/icorem6/Kconfig
index 6d62f0e..4a1c9ac 100644
--- a/board/engicam/icorem6/Kconfig
+++ b/board/engicam/icorem6/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
 	default "engicam"
 
 config SYS_CONFIG_NAME
-	default "imx6qdl_icore"
+	default "imx6-engicam"
 
 endif
diff --git a/board/engicam/icorem6_rqs/Kconfig b/board/engicam/icorem6_rqs/Kconfig
index 1352c68..6dc3a07 100644
--- a/board/engicam/icorem6_rqs/Kconfig
+++ b/board/engicam/icorem6_rqs/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
 	default "engicam"
 
 config SYS_CONFIG_NAME
-	default "imx6qdl_icore_rqs"
+	default "imx6-engicam"
 
 endif
diff --git a/board/engicam/isiotmx6ul/Kconfig b/board/engicam/isiotmx6ul/Kconfig
index 213ffad..10c2c50 100644
--- a/board/engicam/isiotmx6ul/Kconfig
+++ b/board/engicam/isiotmx6ul/Kconfig
@@ -7,6 +7,6 @@ config SYS_VENDOR
 	default "engicam"
 
 config SYS_CONFIG_NAME
-	default "imx6ul_isiot"
+	default "imx6-engicam"
 
 endif
diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c
index 788d3c3..cab769c 100644
--- a/board/freescale/mx25pdk/mx25pdk.c
+++ b/board/freescale/mx25pdk/mx25pdk.c
@@ -175,6 +175,12 @@ int board_mmc_init(bd_t *bis)
 
 	imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads));
 
+	/*
+	 * Set the eSDHC1 PER clock to the maximum frequency lower than or equal
+	 * to 50 MHz that can be obtained, which requires to use UPLL as the
+	 * clock source. This actually gives 48 MHz.
+	 */
+	imx_set_perclk(MXC_ESDHC1_CLK, true, 50000000);
 	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK);
 	return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
 }
diff --git a/board/freescale/mx6sabresd/MAINTAINERS b/board/freescale/mx6sabresd/MAINTAINERS
index add2314..9575261 100644
--- a/board/freescale/mx6sabresd/MAINTAINERS
+++ b/board/freescale/mx6sabresd/MAINTAINERS
@@ -3,6 +3,4 @@ M:	Fabio Estevam <fabio.estevam@nxp.com>
 S:	Maintained
 F:	board/freescale/mx6sabresd/
 F:	include/configs/mx6sabresd.h
-F:	configs/mx6dlsabresd_defconfig
-F:	configs/mx6qsabresd_defconfig
-F:	configs/mx6sabresd_spl_defconfig
+F:	configs/mx6sabresd_defconfig
diff --git a/board/freescale/mx6sabresd/README b/board/freescale/mx6sabresd/README
index bc0c0d0..4b4df06 100644
--- a/board/freescale/mx6sabresd/README
+++ b/board/freescale/mx6sabresd/README
@@ -1,56 +1,47 @@
-How to use and build U-Boot on mx6sabresd:
-----------------------------------
-
-Currently there are four methods for booting mx6sabresd boards:
+How to use and build U-Boot on mx6sabresd
+-----------------------------------------
 
-1. Booting from SD card via normal U-Boot (u-boot.imx)
+The following methods can be used for booting mx6sabresd boards:
 
-2. Booting from eMMC via normal U-Boot
+1. Booting from SD card
 
-3. Booting via SPL (SPL and u-boot.img)
+2. Booting from eMMC
 
-4. Booting via Falcon mode (SPL launches the kernel directly)
+3. Booting via Falcon mode (SPL launches the kernel directly)
 
 
-1. Booting from SD card via normal U-Boot
------------------------------------------
+1. Booting from SD card via SPL
+-------------------------------
 
-$ make mx6qsabresd_defconfig (If you want to build for mx6qsabresd)
+mx6sabresd_defconfig target supports mx6q/mx6dl/mx6qp sabresd variants.
 
-or
+In order to build it:
 
-$ make mx6dlsabresd_defconfig (If you want to build for mx6dlsabresd)
+$ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the image called u-boot.imx.
+This will generate the SPL and u-boot.img binaries.
 
-- Flash the u-boot.imx binary into the SD card:
+- Flash the SPL binary into the SD card:
 
-$ sudo dd if=u-boot.imx of=/dev/sdb bs=1K seek=1 && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
 
+- Flash the u-boot.img binary into the SD card:
 
-2. Booting from eMMC via normal U-Boot
---------------------------------------
+$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
 
-$ make mx6qsabresd_defconfig (If you want to build for mx6qsabresd)
 
-or
+2. Booting from eMMC
+--------------------
 
-$ make mx6dlsabresd_defconfig (If you want to build for mx6dlsabresd)
+$ make mx6sabresd_defconfig
 
 $ make
 
-This will generate the image called u-boot.imx.
-
-- Flash the u-boot.imx binary into the eMMC:
-
-Set SW6 to download mode: 00001100
+This will generate the SPL and u-boot.img binaries.
 
-Plug a usb cable to USB-OTG and load the u-boot image using the imx_usb_loader
-tool (https://github.com/boundarydevices/imx_usb_loader):
-
-$ sudo ./imx_usb u-boot.imx
+- Boot first from SD card as shown in the previous section
 
 In U-boot change the eMMC partition config:
 
@@ -60,48 +51,29 @@ Mount the eMMC in the host PC:
 
 => ums 0 mmc 2
 
-Flash the u-boot.imx binary
+- Flash SPL and u-boot.img binaries into the eMMC:
 
-$ sudo dd if=u-boot.imx of=/dev/sdX bs=1K seek=1 && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
+$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
 
 Set SW6 to eMMC 8-bit boot: 11010110
 
 
-3. Booting via SPL
-------------------
-
-Other method for building U-Boot on mx6qsabresd and mx6qpsabresd is
-through SPL. In order to do so:
-
-$ make mx6sabresd_spl_defconfig
-$ make
-
-This will generate the SPL image called SPL and the u-boot.img.
-
-- Flash the SPL image into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 && sync
-
-- Flash the u-boot.img image into the SD card:
-
-$ sudo dd if=u-boot.img of=/dev/sdbbs=1K seek=69 && sync
-
-
-4. Booting via Falcon mode
+3. Booting via Falcon mode
 --------------------------
 
-$ make mx6sabresd_spl_defconfig
+$ make mx6sabresd_defconfig
 $ make
 
 This will generate the SPL image called SPL and the u-boot.img.
 
 - Flash the SPL image into the SD card:
 
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 oflag=sync status=none && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
 
 - Flash the u-boot.img image into the SD card:
 
-$ sudo dd if=u-boot.img of=/dev/sdbbs=1K seek=69 oflag=sync status=none && sync
+$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
 
 Create a partition for root file system and extract it there:
 
diff --git a/board/technexion/pico-imx7d/Kconfig b/board/technexion/pico-imx7d/Kconfig
new file mode 100644
index 0000000..f4ae18c
--- /dev/null
+++ b/board/technexion/pico-imx7d/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_PICO_IMX7D
+
+config SYS_BOARD
+	default "pico-imx7d"
+
+config SYS_VENDOR
+	default "technexion"
+
+config SYS_SOC
+	default "mx7"
+
+config SYS_CONFIG_NAME
+	default "pico-imx7d"
+
+endif
diff --git a/board/technexion/pico-imx7d/MAINTAINERS b/board/technexion/pico-imx7d/MAINTAINERS
new file mode 100644
index 0000000..276162a
--- /dev/null
+++ b/board/technexion/pico-imx7d/MAINTAINERS
@@ -0,0 +1,7 @@
+Technexion PICO-IMX7D board
+M:	Wig Cheng <wig.cheng@technexion.com>
+M:	Vanessa Maegima <vanessa.maegima@nxp.com>
+S:	Maintained
+F:	board/technexion/pico-imx7d/
+F:	include/configs/pico-imx7d.h
+F:	configs/pico-imx7d_defconfig
diff --git a/board/technexion/pico-imx7d/Makefile b/board/technexion/pico-imx7d/Makefile
new file mode 100644
index 0000000..42cca47
--- /dev/null
+++ b/board/technexion/pico-imx7d/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2017 NXP Semiconductors
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := pico-imx7d.o
diff --git a/board/technexion/pico-imx7d/README b/board/technexion/pico-imx7d/README
new file mode 100644
index 0000000..a2805ee
--- /dev/null
+++ b/board/technexion/pico-imx7d/README
@@ -0,0 +1,49 @@
+How to update U-Boot on pico-imx7d board
+----------------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+Build U-Boot for pico:
+
+$ make mrproper
+$ make pico-imx7d_defconfig
+$ make
+
+This generates the U-Boot binary called u-boot.imx.
+
+Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
+page 3)
+
+Connect a USB to serial adapter between the host PC and pico.
+
+Connect a USB cable between the OTG pico port and the host PC.
+
+Open a terminal program such as minicom.
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the UMS command:
+=> ums 0 mmc 0
+
+Transfer u-boot.imx to be flashed into the eMMC:
+
+$ sudo dd if=u-boot.imx of=/dev/sdX bs=1K seek=1; sync
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode.
+
+Power up the board and the new updated U-Boot should boot from eMMC.
diff --git a/board/technexion/pico-imx7d/imximage.cfg b/board/technexion/pico-imx7d/imximage.cfg
new file mode 100644
index 0000000..202956a
--- /dev/null
+++ b/board/technexion/pico-imx7d/imximage.cfg
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2017 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM	sd
+
+/* Secure boot support */
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000b24
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
diff --git a/board/technexion/pico-imx7d/pico-imx7d.c b/board/technexion/pico-imx7d/pico-imx7d.c
new file mode 100644
index 0000000..799751d
--- /dev/null
+++ b/board/technexion/pico-imx7d/pico-imx7d.c
@@ -0,0 +1,289 @@
+/*
+ * Copyright (C) 2017 NXP Semiconductors
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../../freescale/common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_DSE_3P3V_32OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C4 for PMIC */
+static struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL | PC,
+		.gpio_mode = MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 | PC,
+		.gp = IMX_GPIO_NR(6, 16),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA | PC,
+		.gpio_mode = MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 | PC,
+		.gp = IMX_GPIO_NR(6, 17),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+#ifdef CONFIG_POWER
+#define I2C_PMIC	3
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg, rev_id;
+
+	ret = power_pfuze3000_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	p = pmic_get("PFUZE3000");
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
+	pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
+	printf("PMIC:  PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	pmic_reg_read(p, PFUZE3000_LDOGCTL, &reg);
+	reg |= 0x1;
+	pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(p, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(p, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 1.025V */
+	reg = 0xd;
+	pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
+
+	/* decrease SW1B normal voltage to 0.975V */
+	pmic_reg_read(p, PFUZE3000_SW1BVOLT, &reg);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(975);
+	pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+	MX7D_PAD_I2C4_SCL__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_I2C4_SDA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_GPIO1_IO14__GPIO1_IO14 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__GPIO6_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define FEC1_RST_GPIO	IMX_GPIO_NR(6, 11)
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	gpio_direction_output(FEC1_RST_GPIO, 0);
+	udelay(500);
+	gpio_set_value(FEC1_RST_GPIO, 1);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_fec();
+
+	return fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+	/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17] */
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+			(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
+			IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
+
+	return set_clk_enet(ENET_125MHz);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	unsigned short val;
+
+	/* To enable AR8035 ouput a 125MHz clk from CLK_25M */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	val &= 0xffe7;
+	val |= 0x18;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+	val |= 0x0100;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* Assume uSDHC3 emmc is always present */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(
+			usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset(wdog);
+
+	/*
+	 * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
+	 * since we use PMIC_PWRON to reset the board.
+	 */
+	clrsetbits_le16(&wdog->wcr, 0, 0x10);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: i.MX7D PICOSOM\n");
+
+	return 0;
+}
+
+int board_usb_phy_mode(int port)
+{
+	return USB_INIT_DEVICE;
+}
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
index b7785ba..82a7fc7 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -43,3 +43,5 @@ CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
 CONFIG_VIDEO_IPUV3=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6qdl_icore_nand_defconfig b/configs/imx6qdl_icore_nand_defconfig
new file mode 100644
index 0000000..4bc661e
--- /dev/null
+++ b/configs/imx6qdl_icore_nand_defconfig
@@ -0,0 +1,47 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_MX6Q_ICORE=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+# CONFIG_CMD_BMODE is not set
+CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-icore"
+CONFIG_OF_LIST="imx6q-icore imx6dl-icore"
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,ENV_IS_IN_NAND"
+CONFIG_BOOTDELAY=3
+CONFIG_SPL=y
+CONFIG_SPL_DMA_SUPPORT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="icorem6qdl> "
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_UBI=y
+# CONFIG_BLK is not set
+CONFIG_SYS_I2C_MXC=y
+# CONFIG_DM_MMC_OPS is not set
+CONFIG_NAND_MXS=y
+CONFIG_FEC_MXC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_MXC_UART=y
+CONFIG_IMX_THERMAL=y
+CONFIG_VIDEO_IPUV3=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6qdl_icore_rqs_mmc_defconfig b/configs/imx6qdl_icore_rqs_mmc_defconfig
index e746b48..33427ca 100644
--- a/configs/imx6qdl_icore_rqs_mmc_defconfig
+++ b/configs/imx6qdl_icore_rqs_mmc_defconfig
@@ -40,3 +40,6 @@ CONFIG_FEC_MXC=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ9021=y
diff --git a/configs/imx6ul_geam_mmc_defconfig b/configs/imx6ul_geam_mmc_defconfig
index acaed60..04293e2 100644
--- a/configs/imx6ul_geam_mmc_defconfig
+++ b/configs/imx6ul_geam_mmc_defconfig
@@ -40,3 +40,5 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6ul_geam_nand_defconfig b/configs/imx6ul_geam_nand_defconfig
index baf1a73..f8b071b 100644
--- a/configs/imx6ul_geam_nand_defconfig
+++ b/configs/imx6ul_geam_nand_defconfig
@@ -41,3 +41,5 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6ul_isiot_emmc_defconfig b/configs/imx6ul_isiot_emmc_defconfig
index 4b429c2..5c2d275 100644
--- a/configs/imx6ul_isiot_emmc_defconfig
+++ b/configs/imx6ul_isiot_emmc_defconfig
@@ -38,3 +38,5 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6ul_isiot_mmc_defconfig b/configs/imx6ul_isiot_mmc_defconfig
index 424089c..3ec1288 100644
--- a/configs/imx6ul_isiot_mmc_defconfig
+++ b/configs/imx6ul_isiot_mmc_defconfig
@@ -40,3 +40,5 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/imx6ul_isiot_nand_defconfig b/configs/imx6ul_isiot_nand_defconfig
index fb2bef9..282d923 100644
--- a/configs/imx6ul_isiot_nand_defconfig
+++ b/configs/imx6ul_isiot_nand_defconfig
@@ -41,3 +41,5 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_SMSC=y
diff --git a/configs/mx6sabresd_spl_defconfig b/configs/mx6sabresd_defconfig
similarity index 100%
rename from configs/mx6sabresd_spl_defconfig
rename to configs/mx6sabresd_defconfig
diff --git a/configs/pico-imx7d_defconfig b/configs/pico-imx7d_defconfig
new file mode 100644
index 0000000..35d4486
--- /dev/null
+++ b/configs/pico-imx7d_defconfig
@@ -0,0 +1,35 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX7=y
+CONFIG_TARGET_PICO_IMX7D=y
+CONFIG_IMX_RDC=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx7d/imximage.cfg"
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_G_DNL_MANUFACTURER="FSL"
+CONFIG_G_DNL_VENDOR_NUM=0x0525
+CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
+CONFIG_OF_LIBFDT=y
diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 5ee712f..73748c5 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -521,7 +521,13 @@ out:
 
 static void set_sysctl(struct mmc *mmc, uint clock)
 {
-	int div, pre_div;
+	int div = 1;
+#ifdef ARCH_MXC
+	int pre_div = 1;
+#else
+	int pre_div = 2;
+#endif
+	int ddr_pre_div = mmc->ddr_mode ? 2 : 1;
 	struct fsl_esdhc_priv *priv = mmc->priv;
 	struct fsl_esdhc *regs = priv->esdhc_regs;
 	int sdhc_clk = priv->sdhc_clk;
@@ -530,18 +536,13 @@ static void set_sysctl(struct mmc *mmc, uint clock)
 	if (clock < mmc->cfg->f_min)
 		clock = mmc->cfg->f_min;
 
-	if (sdhc_clk / 16 > clock) {
-		for (pre_div = 2; pre_div < 256; pre_div *= 2)
-			if ((sdhc_clk / pre_div) <= (clock * 16))
-				break;
-	} else
-		pre_div = 2;
+	while (sdhc_clk / (16 * pre_div * ddr_pre_div) > clock && pre_div < 256)
+		pre_div *= 2;
 
-	for (div = 1; div <= 16; div++)
-		if ((sdhc_clk / (div * pre_div)) <= clock)
-			break;
+	while (sdhc_clk / (div * pre_div * ddr_pre_div) > clock && div < 16)
+		div++;
 
-	pre_div >>= mmc->ddr_mode ? 2 : 1;
+	pre_div >>= 1;
 	div -= 1;
 
 	clk = (pre_div << 8) | (div << 4);
@@ -723,20 +724,6 @@ static const struct mmc_ops esdhc_ops = {
 	.getcd		= esdhc_getcd,
 };
 
-static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
-				 struct fsl_esdhc_priv *priv)
-{
-	if (!cfg || !priv)
-		return -EINVAL;
-
-	priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
-	priv->bus_width = cfg->max_bus_width;
-	priv->sdhc_clk = cfg->sdhc_clk;
-	priv->wp_enable  = cfg->wp_enable;
-
-	return 0;
-};
-
 static int fsl_esdhc_init(struct fsl_esdhc_priv *priv)
 {
 	struct fsl_esdhc *regs;
@@ -833,6 +820,21 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv)
 	return 0;
 }
 
+#ifndef CONFIG_DM_MMC
+static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg,
+				 struct fsl_esdhc_priv *priv)
+{
+	if (!cfg || !priv)
+		return -EINVAL;
+
+	priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base);
+	priv->bus_width = cfg->max_bus_width;
+	priv->sdhc_clk = cfg->sdhc_clk;
+	priv->wp_enable  = cfg->wp_enable;
+
+	return 0;
+};
+
 int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg)
 {
 	struct fsl_esdhc_priv *priv;
@@ -871,6 +873,7 @@ int fsl_esdhc_mmc_init(bd_t *bis)
 	cfg->sdhc_clk = gd->arch.sdhc_clk;
 	return fsl_esdhc_initialize(bis, cfg);
 }
+#endif
 
 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT
 void mmc_adapter_card_type_ident(void)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 1afd809..0230852 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -92,6 +92,14 @@ config PHY_MICREL_KSZ9031
 
 endif # PHY_MICREL
 
+config PHY_MICREL_KSZ9021
+	bool "Micrel KSZ9021 Ethernet PHYs support"
+	depends on PHY_MICREL
+	help
+          KSZ9021 is a completely integrated triple speed (10Base-T/100Base-TX/1000Base-T)
+	  Ethernet Physical Layer Transceiver for transmission and reception of data over
+	  standard CAT-5 unshielded twisted pair (UTP) cable.
+
 config PHY_MSCC
 	bool "Microsemi Corp Ethernet PHYs support"
 
diff --git a/drivers/pci/pcie_imx.c b/drivers/pci/pcie_imx.c
index 732d59d..eab0a2b 100644
--- a/drivers/pci/pcie_imx.c
+++ b/drivers/pci/pcie_imx.c
@@ -42,6 +42,9 @@
 
 /* PCIe Port Logic registers (memory-mapped) */
 #define PL_OFFSET 0x700
+#define PCIE_PL_PFLR (PL_OFFSET + 0x08)
+#define PCIE_PL_PFLR_LINK_STATE_MASK		(0x3f << 16)
+#define PCIE_PL_PFLR_FORCE_LINK			(1 << 15)
 #define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
 #define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c)
 #define PCIE_PHY_DEBUG_R1_LINK_UP		(1 << 4)
@@ -445,6 +448,36 @@ static int imx6_pcie_assert_core_reset(void)
 	/* Power up PCIe PHY */
 	setbits_le32(&gpc_regs->cntr, PCIE_PHY_PUP_REQ);
 #else
+	/*
+	 * If the bootloader already enabled the link we need some special
+	 * handling to get the core back into a state where it is safe to
+	 * touch it for configuration.  As there is no dedicated reset signal
+	 * wired up for MX6QDL, we need to manually force LTSSM into "detect"
+	 * state before completely disabling LTSSM, which is a prerequisite
+	 * for core configuration.
+	 *
+	 * If both LTSSM_ENABLE and REF_SSP_ENABLE are active we have a strong
+	 * indication that the bootloader activated the link.
+	 */
+	if (is_mx6dq()) {
+		u32 val, gpr1, gpr12;
+
+		gpr1 = readl(&iomuxc_regs->gpr[1]);
+		gpr12 = readl(&iomuxc_regs->gpr[12]);
+		if ((gpr1 & IOMUXC_GPR1_PCIE_REF_CLK_EN) &&
+		    (gpr12 & IOMUXC_GPR12_PCIE_CTL_2)) {
+			val = readl(MX6_DBI_ADDR + PCIE_PL_PFLR);
+			val &= ~PCIE_PL_PFLR_LINK_STATE_MASK;
+			val |= PCIE_PL_PFLR_FORCE_LINK;
+
+			imx_pcie_fix_dabt_handler(true);
+			writel(val, MX6_DBI_ADDR + PCIE_PL_PFLR);
+			imx_pcie_fix_dabt_handler(false);
+
+			gpr12 &= ~IOMUXC_GPR12_PCIE_CTL_2;
+			writel(val, &iomuxc_regs->gpr[12]);
+		}
+	}
 	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
 	clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
 #endif
@@ -652,6 +685,11 @@ void imx_pcie_init(void)
 	}
 }
 
+void imx_pcie_remove(void)
+{
+	imx6_pcie_assert_core_reset();
+}
+
 /* Probe function. */
 void pci_init_board(void)
 {
diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
index 4702161..02f3894 100644
--- a/drivers/power/regulator/pfuze100.c
+++ b/drivers/power/regulator/pfuze100.c
@@ -1,3 +1,11 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * Peng Fan <peng.fan@nxp.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
 #include <common.h>
 #include <fdtdec.h>
 #include <errno.h>
@@ -306,7 +314,7 @@ static int pfuze100_regulator_probe(struct udevice *dev)
 
 static int pfuze100_regulator_mode(struct udevice *dev, int op, int *opmode)
 {
-	unsigned char val;
+	int val;
 	struct pfuze100_regulator_platdata *plat = dev_get_platdata(dev);
 	struct pfuze100_regulator_desc *desc = plat->desc;
 
@@ -376,7 +384,7 @@ static int pfuze100_regulator_mode(struct udevice *dev, int op, int *opmode)
 
 static int pfuze100_regulator_enable(struct udevice *dev, int op, bool *enable)
 {
-	unsigned char val;
+	int val;
 	int ret, on_off;
 	struct dm_regulator_uclass_platdata *uc_pdata =
 		dev_get_uclass_platdata(dev);
@@ -440,7 +448,7 @@ static int pfuze100_regulator_enable(struct udevice *dev, int op, bool *enable)
 static int pfuze100_regulator_val(struct udevice *dev, int op, int *uV)
 {
 	int i;
-	unsigned char val;
+	int val;
 	struct pfuze100_regulator_platdata *plat = dev_get_platdata(dev);
 	struct pfuze100_regulator_desc *desc = plat->desc;
 	struct dm_regulator_uclass_platdata *uc_pdata =
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6-engicam.h
similarity index 83%
rename from include/configs/imx6qdl_icore.h
rename to include/configs/imx6-engicam.h
index 13fc48f..12a9bfb 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6-engicam.h
@@ -2,13 +2,13 @@
  * Copyright (C) 2016 Amarula Solutions B.V.
  * Copyright (C) 2016 Engicam S.r.l.
  *
- * Configuration settings for the Engicam i.CoreM6 QDL Starter Kits.
+ * Configuration settings for the Engicam i.MX6 SOM Starter Kits.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
-#ifndef __IMX6QLD_ICORE_CONFIG_H
-#define __IMX6QLD_ICORE_CONFIG_H
+#ifndef __IMX6_ENGICAM_CONFIG_H
+#define __IMX6_ENGICAM_CONFIG_H
 
 #include <linux/sizes.h>
 #include "mx6_common.h"
@@ -40,9 +40,8 @@
 	"splashpos=m,m\0" \
 	"image=uImage\0" \
 	"fit_image=fit.itb\0" \
-	"console=ttymxc3\0" \
 	"fdt_high=0xffffffff\0" \
-	"fdt_addr=0x18000000\0" \
+	"fdt_addr=" FDT_ADDR "\0" \
 	"boot_fdt=try\0" \
 	"mmcpart=1\0" \
 	"nandroot=ubi0:rootfs rootfstype=ubifs\0" \
@@ -110,6 +109,14 @@
 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
 #define CONFIG_SYS_HZ			1000
 
+#ifdef CONFIG_MX6UL
+# define DRAM_OFFSET(x)			0x87##x
+# define FDT_ADDR			__stringify(DRAM_OFFSET(800000))
+#else 
+# define DRAM_OFFSET(x)			0x1##x
+# define FDT_ADDR			__stringify(DRAM_OFFSET(8000000))
+#endif
+
 /* Physical Memory Map */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
@@ -130,14 +137,16 @@
 
 /* UART */
 #ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE		UART4_BASE
+# ifdef CONFIG_MX6UL
+#  define CONFIG_MXC_UART_BASE		UART1_BASE
+# else
+#  define CONFIG_MXC_UART_BASE		UART4_BASE
+# endif
 #endif
 
 /* MMC */
 #ifdef CONFIG_FSL_USDHC
 # define CONFIG_SYS_MMC_ENV_DEV		0
-# define CONFIG_SYS_FSL_USDHC_NUM	1
-# define CONFIG_SYS_FSL_ESDHC_ADDR	0
 #endif
 
 /* NAND */
@@ -169,14 +178,15 @@
 
 /* Ethernet */
 #ifdef CONFIG_FEC_MXC
-# define IMX_FEC_BASE			ENET_BASE_ADDR
-# define CONFIG_FEC_MXC_PHYADDR		0
-# define CONFIG_FEC_XCV_TYPE		RMII
-# define CONFIG_ETHPRIME		"FEC"
+# ifdef CONFIG_TARGET_MX6Q_ICORE_RQS
+#  define CONFIG_FEC_MXC_PHYADDR	3
+#  define CONFIG_FEC_XCV_TYPE		RGMII
+# else
+#  define CONFIG_FEC_MXC_PHYADDR	0
+#  define CONFIG_FEC_XCV_TYPE		RMII
+# endif
 
 # define CONFIG_MII
-# define CONFIG_PHYLIB
-# define CONFIG_PHY_SMSC
 #endif
 
 /* Framebuffer */
@@ -202,9 +212,16 @@
 
 # include "imx6_spl.h"
 # ifdef CONFIG_SPL_BUILD
+#  if defined(CONFIG_TARGET_MX6Q_ICORE_RQS) || defined(CONFIG_TARGET_MX6UL_ISIOT)
+#   define CONFIG_SYS_FSL_USDHC_NUM	2
+#  else
+#   define CONFIG_SYS_FSL_USDHC_NUM	1
+#  endif
+
+#  define CONFIG_SYS_FSL_ESDHC_ADDR	0
 #  undef CONFIG_DM_GPIO
 #  undef CONFIG_DM_MMC
 # endif
 #endif
 
-#endif /* __IMX6QLD_ICORE_CONFIG_H */
+#endif /* __IMX6_ENGICAM_CONFIG_H */
diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
index 4598d27..bda9541 100644
--- a/include/configs/imx6_spl.h
+++ b/include/configs/imx6_spl.h
@@ -35,11 +35,6 @@
  */
 #define CONFIG_SPL_PAD_TO		0x11000
 
-/* NAND support */
-#if defined(CONFIG_SPL_NAND_SUPPORT)
-#define CONFIG_SPL_NAND_MXS
-#endif
-
 /* MMC support */
 #if defined(CONFIG_SPL_MMC_SUPPORT)
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
deleted file mode 100644
index a588823..0000000
--- a/include/configs/imx6qdl_icore_rqs.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam i.CoreM6 QDL RQS Starter Kits.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __IMX6QLD_ICORE_RQS_CONFIG_H
-#define __IMX6QLD_ICORE_RQS_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE			SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-#  define CONFIG_ENV_OFFSET		0x100000
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=boot.scr\0" \
-	"image=uImage\0" \
-	"fit_image=fit.itb\0" \
-	"console=ttymxc3\0" \
-	"fdt_high=0xffffffff\0" \
-	"fdt_addr=0x18000000\0" \
-	"boot_fdt=try\0" \
-	"mmcpart=1\0" \
-	"mmcautodetect=yes\0" \
-	"mmcargs=setenv bootargs console=${console},${baudrate} " \
-		"root=${mmcroot}\0" \
-	"loadbootscript=" \
-		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
-	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
-	"loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
-	"fitboot=echo Booting FIT image from mmc ...; " \
-		"run mmcargs; " \
-		"bootm ${loadaddr}\0" \
-	"_mmcboot=run mmcargs; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if run loadfdt; then " \
-				"bootm ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootm; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootm; " \
-		"fi\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"mmc dev ${mmcdev};" \
-		"if mmc rescan; then " \
-			"if run loadbootscript; then " \
-				"run bootscript; " \
-			"else " \
-				"if run loadfit; then " \
-					"run fitboot; " \
-				"else " \
-					"if run loadimage; then " \
-						"run _mmcboot; " \
-					"fi; " \
-				"fi; " \
-			"fi; " \
-		"fi\0"
-
-#define CONFIG_BOOTCOMMAND		"run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START	0x80000000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-#define CONFIG_SYS_HZ			1000
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE		UART4_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV		0
-# define CONFIG_SYS_FSL_USDHC_NUM	2
-# define CONFIG_SYS_FSL_ESDHC_ADDR	0
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR		3
-# define CONFIG_FEC_XCV_TYPE		RGMII
-
-# define CONFIG_MII
-# define CONFIG_PHYLIB
-# define CONFIG_PHY_MICREL
-# define CONFIG_PHY_MICREL_KSZ9021
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# define CONFIG_SPL_MMC_SUPPORT
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-#  undef CONFIG_DM_GPIO
-#  undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6QLD_ICORE_RQS_CONFIG_H */
diff --git a/include/configs/imx6ul_geam.h b/include/configs/imx6ul_geam.h
deleted file mode 100644
index 1d48726..0000000
--- a/include/configs/imx6ul_geam.h
+++ /dev/null
@@ -1,194 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam GEAM6UL  Starter Kits.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __IMX6UL_GEAM_CONFIG_H
-#define __IMX6UL_GEAM_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE			SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-#  define CONFIG_ENV_OFFSET		0x100000
-/* Environment in NAND */
-# elif defined(CONFIG_ENV_IS_IN_NAND)
-#  define CONFIG_ENV_OFFSET		0x400000
-#  define CONFIG_ENV_SECT_SIZE		CONFIG_ENV_SIZE
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=boot.scr\0" \
-	"image=uImage\0" \
-	"fit_image=fit.itb\0" \
-	"console=ttymxc0\0" \
-	"fdt_high=0xffffffff\0" \
-	"fdt_addr=0x87800000\0" \
-	"boot_fdt=try\0" \
-	"mmcpart=1\0" \
-	"nandroot=ubi0:rootfs rootfstype=ubifs\0" \
-	"mmcautodetect=yes\0" \
-	"mmcargs=setenv bootargs console=${console},${baudrate} " \
-		"root=${mmcroot}\0" \
-	"ubiargs=setenv bootargs console=${console},${baudrate} " \
-		"ubi.mtd=5 root=${nandroot} ${mtdparts}\0" \
-	"loadbootscript=" \
-		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
-	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
-	"loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
-	"fitboot=echo Booting FIT image from mmc ...; " \
-		"run mmcargs; " \
-		"bootm ${loadaddr}\0" \
-	"_mmcboot=run mmcargs; " \
-		"run mmcargs; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if run loadfdt; then " \
-				"bootm ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootm; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootm; " \
-		"fi\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"if mmc rescan; then " \
-			"if run loadbootscript; then " \
-				"run bootscript; " \
-			"else " \
-				"if run loadfit; then " \
-					"run fitboot; " \
-				"else " \
-					"if run loadimage; then " \
-						"run _mmcboot; " \
-					"fi; " \
-				"fi; " \
-			"fi; " \
-		"fi\0" \
-	"nandboot=echo Booting from nand ...; " \
-		"if mtdparts; then " \
-			"echo Starting nand boot ...; " \
-		"else " \
-			"mtdparts default; " \
-		"fi; " \
-		"run ubiargs; " \
-		"nand read ${loadaddr} kernel 0x800000; " \
-		"nand read ${fdt_addr} dtb 0x100000; " \
-		"bootm ${loadaddr} - ${fdt_addr}\0"
-
-#define CONFIG_BOOTCOMMAND		"run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START	0x80000000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-#define CONFIG_SYS_HZ			1000
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE		UART1_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV		0
-# define CONFIG_SYS_FSL_USDHC_NUM	1
-# define CONFIG_SYS_FSL_ESDHC_ADDR	0
-#endif
-
-/* NAND */
-#ifdef CONFIG_NAND_MXS
-# define CONFIG_SYS_MAX_NAND_DEVICE	1
-# define CONFIG_SYS_NAND_BASE		0x40000000
-# define CONFIG_SYS_NAND_5_ADDR_CYCLE
-# define CONFIG_SYS_NAND_ONFI_DETECTION
-# define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
-# define CONFIG_SYS_NAND_U_BOOT_OFFS	0x200000
-
-/* MTD device */
-# define CONFIG_MTD_DEVICE
-# define CONFIG_CMD_MTDPARTS
-# define CONFIG_MTD_PARTITIONS
-# define MTDIDS_DEFAULT			"nand0=gpmi-nand"
-# define MTDPARTS_DEFAULT		"mtdparts=gpmi-nand:2m(spl),2m(uboot)," \
-					"1m(env),8m(kernel),1m(dtb),-(rootfs)"
-
-/* UBI */
-# define CONFIG_CMD_UBIFS
-# define CONFIG_RBTREE
-# define CONFIG_LZO
-
-# define CONFIG_APBH_DMA
-# define CONFIG_APBH_DMA_BURST
-# define CONFIG_APBH_DMA_BURST8
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR		0
-# define CONFIG_FEC_XCV_TYPE		RMII
-
-# define CONFIG_MII
-# define CONFIG_PHYLIB
-# define CONFIG_PHY_SMSC
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# ifdef CONFIG_NAND_MXS
-#  define CONFIG_SPL_NAND_SUPPORT
-# else
-#  define CONFIG_SPL_MMC_SUPPORT
-# endif
-
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-#  undef CONFIG_DM_GPIO
-#  undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6UL_GEAM_CONFIG_H */
diff --git a/include/configs/imx6ul_isiot.h b/include/configs/imx6ul_isiot.h
deleted file mode 100644
index a0eb6e2..0000000
--- a/include/configs/imx6ul_isiot.h
+++ /dev/null
@@ -1,195 +0,0 @@
-/*
- * Copyright (C) 2016 Amarula Solutions B.V.
- * Copyright (C) 2016 Engicam S.r.l.
- *
- * Configuration settings for the Engicam Is.IoT MX6UL Starter Kits.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __IMX6UL_ISIOT_CONFIG_H
-#define __IMX6UL_ISIOT_CONFIG_H
-
-#include <linux/sizes.h>
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
-
-/* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE			SZ_128K
-
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Environment */
-#ifndef CONFIG_ENV_IS_NOWHERE
-/* Environment in MMC */
-# if defined(CONFIG_ENV_IS_IN_MMC)
-#  define CONFIG_ENV_OFFSET		0x100000
-/* Environment in NAND */
-# elif defined(CONFIG_ENV_IS_IN_NAND)
-#  define CONFIG_ENV_OFFSET		0x400000
-#  define CONFIG_ENV_SECT_SIZE		CONFIG_ENV_SIZE
-# endif
-#endif
-
-/* Default environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=boot.scr\0" \
-	"image=uImage\0" \
-	"fit_image=fit.itb\0" \
-	"splashpos=m,m\0" \
-	"console=ttymxc0\0" \
-	"fdt_high=0xffffffff\0" \
-	"fdt_addr=0x87800000\0" \
-	"boot_fdt=try\0" \
-	"mmcpart=1\0" \
-	"nandroot=ubi0:rootfs rootfstype=ubifs\0" \
-	"mmcautodetect=yes\0" \
-	"mmcargs=setenv bootargs console=${console},${baudrate} " \
-		"root=${mmcroot}\0" \
-	"ubiargs=setenv bootargs console=${console},${baudrate} " \
-		"ubi.mtd=5 root=${nandroot} ${mtdparts}\0" \
-	"loadbootscript=" \
-		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
-	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
-	"loadfit=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${fit_image}\0" \
-	"fitboot=echo Booting FIT image from mmc ...; " \
-		"run mmcargs; " \
-		"bootm ${loadaddr}\0" \
-	"_mmcboot=run mmcargs; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if run loadfdt; then " \
-				"bootm ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootm; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootm; " \
-		"fi\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"if mmc rescan; then " \
-			"if run loadbootscript; then " \
-				"run bootscript; " \
-			"else " \
-				"if run loadfit; then " \
-					"run fitboot; " \
-				"else " \
-					"if run loadimage; then " \
-						"run _mmcboot; " \
-					"fi; " \
-				"fi; " \
-			"fi; " \
-		"fi\0" \
-	"nandboot=echo Booting from nand ...; " \
-		"if mtdparts; then " \
-			"echo Starting nand boot ...; " \
-		"else " \
-			"mtdparts default; " \
-		"fi; " \
-		"run ubiargs; " \
-		"nand read ${loadaddr} kernel 0x800000; " \
-		"nand read ${fdt_addr} dtb 0x100000; " \
-		"bootm ${loadaddr} - ${fdt_addr}\0"
-
-#define CONFIG_BOOTCOMMAND		"run $modeboot"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START	0x80000000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-#define CONFIG_SYS_HZ			1000
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FIT */
-#ifdef CONFIG_FIT
-# define CONFIG_IMAGE_FORMAT_LEGACY
-#endif
-
-/* UART */
-#ifdef CONFIG_MXC_UART
-# define CONFIG_MXC_UART_BASE		UART1_BASE
-#endif
-
-/* MMC */
-#ifdef CONFIG_FSL_USDHC
-# define CONFIG_SYS_MMC_ENV_DEV		0
-# define CONFIG_SYS_FSL_USDHC_NUM	2
-# define CONFIG_SYS_FSL_ESDHC_ADDR	0
-#endif
-
-/* NAND */
-#ifdef CONFIG_NAND_MXS
-# define CONFIG_SYS_MAX_NAND_DEVICE	1
-# define CONFIG_SYS_NAND_BASE		0x40000000
-# define CONFIG_SYS_NAND_5_ADDR_CYCLE
-# define CONFIG_SYS_NAND_ONFI_DETECTION
-# define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
-# define CONFIG_SYS_NAND_U_BOOT_OFFS	0x200000
-
-/* MTD device */
-# define CONFIG_MTD_DEVICE
-# define CONFIG_CMD_MTDPARTS
-# define CONFIG_MTD_PARTITIONS
-# define MTDIDS_DEFAULT			"nand0=gpmi-nand"
-# define MTDPARTS_DEFAULT		"mtdparts=gpmi-nand:2m(spl),2m(uboot)," \
-					"1m(env),8m(kernel),1m(dtb),-(rootfs)"
-
-/* UBI */
-# define CONFIG_CMD_UBIFS
-# define CONFIG_RBTREE
-# define CONFIG_LZO
-
-/* APBH DMA */
-# define CONFIG_APBH_DMA
-# define CONFIG_APBH_DMA_BURST
-# define CONFIG_APBH_DMA_BURST8
-#endif
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-# define CONFIG_FEC_MXC_PHYADDR		0
-# define CONFIG_FEC_XCV_TYPE		RMII
-
-# define CONFIG_MII
-# define CONFIG_PHYLIB
-# define CONFIG_PHY_SMSC
-#endif
-
-/* SPL */
-#ifdef CONFIG_SPL
-# ifdef CONFIG_NAND_MXS
-#  define CONFIG_SPL_NAND_SUPPORT
-# else
-#  define CONFIG_SPL_MMC_SUPPORT
-# endif
-
-# include "imx6_spl.h"
-# ifdef CONFIG_SPL_BUILD
-#  undef CONFIG_DM_GPIO
-#  undef CONFIG_DM_MMC
-# endif
-#endif
-
-#endif /* __IMX6UL_ISIOT_CONFIG_H */
diff --git a/include/configs/mx7dsabresd.h b/include/configs/mx7dsabresd.h
index 39291a2..fe9fd66 100644
--- a/include/configs/mx7dsabresd.h
+++ b/include/configs/mx7dsabresd.h
@@ -207,7 +207,7 @@
 #define CONFIG_APBH_DMA_BURST8
 #endif
 
-#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#define CONFIG_ENV_OFFSET		(12 * SZ_64K)
 #ifdef CONFIG_NAND_MXS
 #define CONFIG_SYS_FSL_USDHC_NUM	1
 #else
diff --git a/include/configs/pico-imx7d.h b/include/configs/pico-imx7d.h
new file mode 100644
index 0000000..d128ede
--- /dev/null
+++ b/include/configs/pico-imx7d.h
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2017 NXP Semiconductors
+ *
+ * Configuration settings for the i.MX7D Pico board.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __PICO_IMX7D_CONFIG_H
+#define __PICO_IMX7D_CONFIG_H
+
+#include "mx7_common.h"
+
+#define PHYS_SDRAM_SIZE		SZ_1G
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)
+
+#define CONFIG_MXC_UART_BASE		UART5_IPS_BASE_ADDR
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		1
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* ENET1 */
+#define IMX_FEC_BASE			ENET_IPS_BASE_ADDR
+
+/* MMC Config */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"image=zImage\0" \
+	"console=ttymxc4\0" \
+	"fdt_high=0xffffffff\0" \
+	"initrd_high=0xffffffff\0" \
+	"fdt_file=imx7d-pico.dtb\0" \
+	"fdt_addr=0x83000000\0" \
+	"ip_dyn=yes\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"finduuid=part uuid mmc 0:2 uuid\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=PARTUUID=${uuid} rootwait rw\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run finduuid; " \
+		"run mmcargs; " \
+		"if run loadfdt; then " \
+			"bootz ${loadaddr} - ${fdt_addr}; " \
+		"else " \
+			"echo WARN: Cannot load the DT; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+		"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${image}; " \
+		"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+			"bootz ${loadaddr} - ${fdt_addr}; " \
+		"else " \
+			"echo WARN: Cannot load the DT; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc rescan; then " \
+		"if run loadimage; then " \
+			"run mmcboot; " \
+		"else run netboot; " \
+		"fi; " \
+	"else run netboot; fi"
+
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* I2C configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE3000
+#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_IS_IN_MMC
+
+#define CONFIG_ENV_OFFSET			(8 * SZ_64K)
+#define CONFIG_SYS_FSL_USDHC_NUM		2
+
+#define CONFIG_SYS_MMC_ENV_DEV			0
+#define CONFIG_SYS_MMC_ENV_PART		0
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC			(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS			0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_USB_FUNCTION_MASS_STORAGE
+
+#endif
diff --git a/include/pci.h b/include/pci.h
index d3c955e..c8ef997 100644
--- a/include/pci.h
+++ b/include/pci.h
@@ -754,6 +754,10 @@ int pci_last_busno(void);
 extern void pci_mpc85xx_init (struct pci_controller *hose);
 #endif
 
+#ifdef CONFIG_PCIE_IMX
+extern void imx_pcie_remove(void);
+#endif
+
 #if !defined(CONFIG_DM_PCI) || defined(CONFIG_DM_PCI_COMPAT)
 /**
  * pci_write_bar32() - Write the address of a BAR including control bits
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index feb430f..31cbb86 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -2498,7 +2498,6 @@ CONFIG_SPL_NAND_ECC
 CONFIG_SPL_NAND_INIT
 CONFIG_SPL_NAND_LOAD
 CONFIG_SPL_NAND_MINIMAL
-CONFIG_SPL_NAND_MXS
 CONFIG_SPL_NAND_RAW_ONLY
 CONFIG_SPL_NAND_SIMPLE
 CONFIG_SPL_NAND_SOFTECC