[PATCH] Use dynamic SDRAM TLB setup on AMCC Ebony eval board

Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).

Signed-off-by: Stefan Roese <sr@denx.de>
master
Stefan Roese 18 years ago
parent 76d1466f91
commit 8423e5e31a
  1. 77
      board/amcc/ebony/init.S
  2. 5
      include/configs/ebony.h

@ -22,53 +22,7 @@
#include <ppc_asm.tmpl>
#include <config.h>
/* General */
#define TLB_VALID 0x00000200
/* Supported page sizes */
#define SZ_1K 0x00000000
#define SZ_4K 0x00000010
#define SZ_16K 0x00000020
#define SZ_64K 0x00000030
#define SZ_256K 0x00000040
#define SZ_1M 0x00000050
#define SZ_16M 0x00000070
#define SZ_256M 0x00000090
/* Storage attributes */
#define SA_W 0x00000800 /* Write-through */
#define SA_I 0x00000400 /* Caching inhibited */
#define SA_M 0x00000200 /* Memory coherence */
#define SA_G 0x00000100 /* Guarded */
#define SA_E 0x00000080 /* Endian */
/* Access control */
#define AC_X 0x00000024 /* Execute */
#define AC_W 0x00000012 /* Write */
#define AC_R 0x00000009 /* Read */
/* Some handy macros */
#define EPN(e) ((e) & 0xfffffc00)
#define TLB0(epn,sz) ( (EPN((epn)) | (sz) | TLB_VALID ) )
#define TLB1(rpn,erpn) ( ((rpn)&0xfffffc00) | (erpn) )
#define TLB2(a) ( (a)&0x00000fbf )
#define tlbtab_start\
mflr r1 ;\
bl 0f ;
#define tlbtab_end\
.long 0, 0, 0 ; \
0: mflr r0 ; \
mtlr r1 ; \
blr ;
#define tlbentry(epn,sz,rpn,erpn,attr)\
.long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
#include <asm-ppc/mmu.h>
/**************************************************************************
* TLB TABLE
@ -81,16 +35,23 @@
*
*************************************************************************/
.section .bootpg,"ax"
.globl tlbtab
.section .bootpg,"ax"
.globl tlbtab
tlbtab:
tlbtab_start
tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
tlbentry( CFG_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_R|AC_W|SA_G|SA_I)
tlbentry( CFG_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_R|AC_W|AC_X )
tlbentry( CFG_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_R|AC_W|AC_X )
tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
tlbentry( CFG_PCI_BASE, SZ_256M, 0x00000000, 2, AC_R|AC_W|SA_G|SA_I )
tlbentry( CFG_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_R|AC_W|SA_G|SA_I )
tlbtab_end
tlbtab_start
tlbentry(0xf0000000, SZ_256M, 0xf0000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
/*
* TLB entries for SDRAM are not needed on this platform.
* They are dynamically generated in the SPD DDR(2) detection
* routine.
*/
tlbentry(CFG_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_R|AC_W|AC_X)
tlbentry(CFG_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_R|AC_W|AC_X)
tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 2, AC_R|AC_W|SA_G|SA_I)
tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_R|AC_W|SA_G|SA_I)
tlbtab_end

@ -133,8 +133,9 @@
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x53,0x52} /* SPD i2c spd addresses */
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x53,0x52} /* SPD i2c spd addresses */
#define CONFIG_PROG_SDRAM_TLB 1 /* setup SDRAM TLB's dynamically*/
/*-----------------------------------------------------------------------
* I2C

Loading…
Cancel
Save