powerpc/mpc85xx:Put errata number for T104x NAND boot issue

When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.

Workaround is already in-place.
Put the errata number to adhere errata handling framework.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
master
Prabhakar Kushwaha 10 years ago committed by York Sun
parent 1b2af9b4e2
commit 9f074e67f5
  1. 4
      README
  2. 5
      arch/powerpc/cpu/mpc85xx/cmd_errata.c
  3. 1
      arch/powerpc/include/asm/config_mpc85xx.h
  4. 4
      board/freescale/t104xrdb/spl.c
  5. 10
      include/configs/T104xRDB.h

@ -409,6 +409,10 @@ The following options need to be configured:
Enables a workaround for IFC erratum A003399. It is only
requred during NOR boot.
CONFIG_A008044_WORKAROUND
Enables a workaround for T1040/T1042 erratum A008044. It is only
requred during NAND boot and valid for Rev 1.0 SoC revision
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600

@ -313,7 +313,10 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
puts("Work-around for Erratum A-005434 enabled\n");
#endif
#if defined(CONFIG_SYS_FSL_ERRATUM_A008044) && \
defined(CONFIG_A008044_WORKAROUND)
puts("Work-around for Erratum A-008044 enabled\n");
#endif
return 0;
}

@ -769,6 +769,7 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022)
#define CONFIG_SYS_PME_CLK CONFIG_PME_PLAT_CLK_DIV
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
#define CONFIG_SYS_FSL_ERRATUM_A008044
#define CONFIG_SYS_FMAN_V3
#define CONFIG_FM_PLAT_CLK_DIV 1
#define CONFIG_SYS_FM1_CLK CONFIG_FM_PLAT_CLK_DIV

@ -34,12 +34,12 @@ unsigned long get_board_ddr_clk(void)
void board_init_f(ulong bootflag)
{
u32 plat_ratio, sys_clk, uart_clk;
#ifdef CONFIG_SPL_NAND_BOOT
#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND)
u32 porsr1, pinctl;
#endif
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
#ifdef CONFIG_SPL_NAND_BOOT
#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND)
/*
* There is T1040 SoC issue where NOR, FPGA are inaccessible during
* NAND boot because IFC signals > IFC_AD7 are not enabled.

@ -13,6 +13,9 @@
#define CONFIG_T104xRDB
#define CONFIG_PHYS_64BIT
#define CONFIG_E500 /* BOOKE e500 family */
#include <asm/config_mpc85xx.h>
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg
#ifdef CONFIG_T1040RDB
@ -93,7 +96,6 @@
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_MP /* support multiple processors */
@ -386,6 +388,12 @@
#define CONFIG_SYS_RAMBOOT
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A008044
#if defined(CONFIG_NAND)
#define CONFIG_A008044_WORKAROUND
#endif
#endif
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R

Loading…
Cancel
Save