@ -183,7 +183,7 @@ Directory Hierarchy:
/nios2 Files generic to Altera NIOS2 architecture
/cpu CPU specific files
/lib Architecture specific library files
/ppc Files generic to PowerPC architecture
/power pc Files generic to PowerPC architecture
/cpu CPU specific files
/74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
/mpc5xx Files specific to Freescale MPC5xx CPUs
@ -1417,7 +1417,7 @@ The following options need to be configured:
the CPU's i2c node address).
Now, the u-boot i2c code for the mpc8xx
(arch/ppc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
(arch/power pc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
and so its address should therefore be cleared to 0 (See,
eg, MPC823e User's Manual p.16-473). So, set
CONFIG_SYS_I2C_SLAVE to 0.
@ -1966,7 +1966,7 @@ Legacy uImage format:
15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
-30 arch/ppc/lib/board.c Fatal error, hang the system
-30 arch/power pc/lib/board.c Fatal error, hang the system
-31 post/post.c POST test failed, detected by post_output_backlog()
-32 post/post.c POST test failed, detected by post_run_single()
@ -2727,7 +2727,7 @@ Low Level (hardware related) configuration options:
CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
Overrides the default PCI memory map in arch/ppc/cpu/mpc8260/pci.c if set.
Overrides the default PCI memory map in arch/power pc/cpu/mpc8260/pci.c if set.
- CONFIG_PCI_DISABLE_PCIE:
Disable PCI-Express on systems where it is supported but not
@ -3373,7 +3373,7 @@ configure the Linux device drivers for use with your target hardware
(no, we don't intend to provide a full virtual machine interface to
Linux :-).
But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
But now you can ignore ALL boot loader code (in arch/power pc/mbxboot).
Just make sure your machine specific header file (for instance
include/asm-ppc/tqm8xx.h) includes the same definition of the Board
@ -3471,7 +3471,7 @@ So a typical call to build a U-Boot image would read:
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
> -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
> -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/power pc/coffboot/vmlinux.gz \
> examples/uImage.TQM850L
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000
@ -3495,10 +3495,10 @@ speed for memory and install an UNCOMPRESSED image instead: this
needs more space in Flash, but boots much faster since it does not
need to be uncompressed:
-> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
-> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/power pc/coffboot/vmlinux.gz
-> tools/mkimage -n '2.4.4 kernel for TQM850L' \
> -A ppc -O linux -T kernel -C none -a 0 -e 0 \
> -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
> -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/power pc/coffboot/vmlinux \
> examples/uImage.TQM850L-uncompressed
Image Name: 2.4.4 kernel for TQM850L
Created: Wed Jul 19 02:34:59 2000