diff --git a/README b/README index 2ca0102..f4eecd0 100644 --- a/README +++ b/README @@ -3708,11 +3708,6 @@ Configuration Settings: If defined, don't allow the -f switch to env set override variable access flags. -- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) - This is set by OMAP boards for the max time that reset should - be asserted. See doc/README.omap-reset-time for details on how - the value can be calculated on a given board. - - CONFIG_USE_STDINT If stdint.h is available with your toolchain you can define this option to enable it. You can provide option 'USE_STDINT=1' when diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 7ea7199..0c99bbd 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -370,13 +370,6 @@ #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 -/* - * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff. - * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles - * into microsec and passing the value. - */ -#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219 - #if defined(CONFIG_DRA7XX) #define V_OSCK 20000000 /* Clock output from T2 */ #else diff --git a/arch/arm/mach-omap2/omap5/Kconfig b/arch/arm/mach-omap2/omap5/Kconfig index c89c438..1a66abd 100644 --- a/arch/arm/mach-omap2/omap5/Kconfig +++ b/arch/arm/mach-omap2/omap5/Kconfig @@ -63,6 +63,23 @@ config TI_SECURE_EMIF_PROTECTED_REGION_SIZE using hardware memory firewalls. This value must be smaller than the TI_SECURE_EMIF_TOTAL_REGION_SIZE value. +config OMAP_PLATFORM_RESET_TIME_MAX_USEC + int "Something" + range 0 31219 + default 31219 + help + Most OMAPs' provide a way to specify the time for which the reset + should be held low while the voltages and Oscillator outputs + stabilize. + This time is mostly board and PMIC dependent. Hence the boards are + expected to specify a pre-computed time using the above option. + This value can be computed using a summation of the below 3 + parameters + 1: Time taken by the Osciallator to stop and restart + 2: PMIC OTP time + 3: Voltage ramp time, which can be derived using the PMIC slew rate + and value of voltage ramp needed. + if TARGET_DRA7XX_EVM || TARGET_AM57XX_EVM menu "Voltage Domain OPP selections" diff --git a/arch/arm/mach-omap2/omap5/hwinit.c b/arch/arm/mach-omap2/omap5/hwinit.c index 839d79d..afe59e0 100644 --- a/arch/arm/mach-omap2/omap5/hwinit.c +++ b/arch/arm/mach-omap2/omap5/hwinit.c @@ -414,12 +414,13 @@ void setup_warmreset_time(void) { u32 rst_time, rst_val; -#ifndef CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC - rst_time = CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC; -#else - rst_time = CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC; -#endif - rst_time = usec_to_32k(rst_time) << RSTTIME1_SHIFT; + /* + * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff. + * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles + * into microsec and passing the value. + */ + rst_time = usec_to_32k(CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC) + << RSTTIME1_SHIFT; if (rst_time > RSTTIME1_MASK) rst_time = RSTTIME1_MASK; diff --git a/configs/cm_t54_defconfig b/configs/cm_t54_defconfig index d7fd995..0afc6a2 100644 --- a/configs/cm_t54_defconfig +++ b/configs/cm_t54_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y CONFIG_OMAP54XX=y CONFIG_TARGET_CM_T54=y +CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 diff --git a/configs/omap5_uevm_defconfig b/configs/omap5_uevm_defconfig index 865845e..9eefec5 100644 --- a/configs/omap5_uevm_defconfig +++ b/configs/omap5_uevm_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y CONFIG_OMAP54XX=y CONFIG_TARGET_OMAP5_UEVM=y +CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_ARMV7_LPAE=y CONFIG_SYS_CONSOLE_INFO_QUIET=y diff --git a/doc/README.omap-reset-time b/doc/README.omap-reset-time deleted file mode 100644 index 0c974ba..0000000 --- a/doc/README.omap-reset-time +++ /dev/null @@ -1,20 +0,0 @@ -README on how reset time on OMAPs should be calculated - -CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC: -Most OMAPs' provide a way to specify the time for -which the reset should be held low while the voltages -and Oscillator outputs stabilize. - -This time is mostly board and PMIC dependent. Hence the -boards are expected to specify a pre-computed time -using the above option, (the details on how to compute -the value are given below) without which a default time -as specified by CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC -is used. - -The value for CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC -can be computed using a summation of the below 3 parameters --1- Time taken by the Osciallator to stop and restart --2- PMIC OTP time --3- Voltage ramp time, which can be derived using the -PMIC slew rate and value of voltage ramp needed. diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h index 477aa07..d7e7c29 100644 --- a/include/configs/cm_t54.h +++ b/include/configs/cm_t54.h @@ -86,9 +86,6 @@ #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_MCS7830 -/* Max time to hold reset on this board, see doc/README.omap-reset-time */ -#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 - /* * Miscellaneous configurable options */ diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 533bb02..6ac5d50 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -68,9 +68,6 @@ #define CONSOLEDEV "ttyO2" -/* Max time to hold reset on this board, see doc/README.omap-reset-time */ -#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 - #define CONFIG_SCSI #define CONFIG_LIBATA #define CONFIG_SCSI_AHCI diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 5febd2a..8771904 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -617,7 +617,6 @@ CONFIG_DEEP_SLEEP CONFIG_DEFAULT CONFIG_DEFAULT_CONSOLE CONFIG_DEFAULT_IMMR -CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC CONFIG_DEFAULT_SPI_BUS CONFIG_DEFAULT_SPI_CS CONFIG_DEFAULT_SPI_MODE @@ -1999,7 +1998,6 @@ CONFIG_OMAP_EHCI_PHY1_RESET_GPIO CONFIG_OMAP_EHCI_PHY2_RESET_GPIO CONFIG_OMAP_EHCI_PHY3_RESET_GPIO CONFIG_OMAP_GPIO -CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC CONFIG_OMAP_USB2PHY2_HOST CONFIG_OMAP_USB3PHY1_HOST CONFIG_OMAP_USB_PHY