Coding style cleanup; update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

board/davinci/dvevm/dvevm.c

@@ -124,4 +124,3 @@ void enable_vbus(void)
 	i2c_write(IOEXP_I2C_ADDR, 0, 0, &data, 1);
 }
 #endif
-

board/omap3/evm/Makefile

@@ -45,4 +45,3 @@ distclean:	clean
 include $(SRCTREE)/rules.mk
 
 sinclude $(obj).depend
-

board/omap3/overo/Makefile

@@ -45,4 +45,3 @@ distclean:	clean
 include $(SRCTREE)/rules.mk
 
 sinclude $(obj).depend
-

cpu/arm_cortexa8/cpu.c

@@ -238,4 +238,3 @@ static void cache_flush(void)
 {
 	asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (0));
 }
-

doc/README.korat

@@ -51,7 +51,6 @@ leaving preprocessor symbol "CONFIG_KORAT_PERMANENT" undefined.
 2008-02-22, Larry Johnson <lrj@acm.org>
 
 
-
 The CompactFlash(R) controller on the Korat board provides a hi-speed USB
 interface.  This may be connected to either a dedicated port on the on-board
 USB controller, or to a USB port on the PowerPC 440EPx processor.  The U-Boot

doc/README.mpc8572ds

@@ -97,70 +97,70 @@ Implementing AMP(Asymmetric MultiProcessing)
 -------------
 1. Build kernel image for core0:
 
-        a. $ make 85xx/mpc8572_ds_defconfig
+	a. $ make 85xx/mpc8572_ds_defconfig
 
-        b. $ make menuconfig
-           - un-select "Processor support"->"Symetric multi-processing support"
+	b. $ make menuconfig
+	   - un-select "Processor support"->"Symetric multi-processing support"
 
-        c. $ make uImage
+	c. $ make uImage
 
 	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
 
 2. Build kernel image for core1:
 
-        a. $ make 85xx/mpc8572_ds_defconfig
+	a. $ make 85xx/mpc8572_ds_defconfig
 
-        b. $ make menuconfig
-           - Un-select "Processor support"->"Symetric multi-processing support"
-           - Select "Advanced setup" -> " Prompt for advanced kernel
-             configuration options"
-                - Select "Set physical address where the kernel is loaded" and
-                  set it to 0x20000000, asssuming core1 will start from 512MB.
-                - Select "Set custom page offset address"
-                - Select "Set custom kernel base address"
-                - Select "Set maximum low memory"
-           - "Exit" and save the selection.
+	b. $ make menuconfig
+	   - Un-select "Processor support"->"Symetric multi-processing support"
+	   - Select "Advanced setup" -> " Prompt for advanced kernel
+	     configuration options"
+		- Select "Set physical address where the kernel is loaded" and
+		  set it to 0x20000000, asssuming core1 will start from 512MB.
+		- Select "Set custom page offset address"
+		- Select "Set custom kernel base address"
+		- Select "Set maximum low memory"
+	   - "Exit" and save the selection.
 
-        c. $ make uImage
+	c. $ make uImage
 
 	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
 
 3. Create dtb for core0:
 
-        $ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
+	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
 
 4. Create dtb for core1:
 
-        $ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
+	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
 
 5. Bring up two cores separately:
 
-        a. Power on the board, under u-boot prompt:
-                => setenv <serverip>
-                => setenv <ipaddr>
-                => setenv bootargs root=/dev/ram rw console=ttyS0,115200
-        b. Bring up core1's kernel first:
-                => setenv bootm_low 0x20000000
-                => setenv bootm_size 0x10000000
-                => tftp 21000000 8572/uImage.core1
-                => tftp 22000000 8572/ramdiskfile
-                => tftp 20c00000 8572/mpc8572ds_core1.dtb
-                => interrupts off
-                => bootm start 21000000 22000000 20c00000
-                => bootm loados
-                => bootm ramdisk
-                => bootm fdt
-                => fdt boardsetup
-                => fdt chosen $initrd_start $initrd_end
-                => bootm prep
-                => cpu 1 release $bootm_low - $fdtaddr -
-        c. Bring up core0's kernel(on the same u-boot console):
-                => setenv bootm_low 0
-                => setenv bootm_size 0x20000000
-                => tftp 1000000 8572/uImage.core0
-                => tftp 2000000 8572/ramdiskfile
-                => tftp c00000 8572/mpc8572ds_core0.dtb
-                => bootm 1000000 2000000 c00000
+	a. Power on the board, under u-boot prompt:
+		=> setenv <serverip>
+		=> setenv <ipaddr>
+		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
+	b. Bring up core1's kernel first:
+		=> setenv bootm_low 0x20000000
+		=> setenv bootm_size 0x10000000
+		=> tftp 21000000 8572/uImage.core1
+		=> tftp 22000000 8572/ramdiskfile
+		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
+		=> interrupts off
+		=> bootm start 21000000 22000000 20c00000
+		=> bootm loados
+		=> bootm ramdisk
+		=> bootm fdt
+		=> fdt boardsetup
+		=> fdt chosen $initrd_start $initrd_end
+		=> bootm prep
+		=> cpu 1 release $bootm_low - $fdtaddr -
+	c. Bring up core0's kernel(on the same u-boot console):
+		=> setenv bootm_low 0
+		=> setenv bootm_size 0x20000000
+		=> tftp 1000000 8572/uImage.core0
+		=> tftp 2000000 8572/ramdiskfile
+		=> tftp c00000 8572/mpc8572ds_core0.dtb
+		=> bootm 1000000 2000000 c00000
 
 Please note only core0 will run u-boot, core1 starts kernel directly after
 "cpu release" command is issued.

drivers/usb/davinci_usb.h

@@ -84,4 +84,3 @@ extern int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len);
 extern int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len);
 extern void enable_vbus(void);
 #endif	/* __DAVINCI_USB_H__ */
-

drivers/usb/musb_core.h

@@ -314,4 +314,3 @@ extern inline u16 musb_readw(u32 offset);
 extern inline u8 musb_readb(u32 offset);
 
 #endif	/* __MUSB_HDRC_DEFS_H__ */
-

drivers/usb/usb_ehci_core.c

@@ -818,8 +818,10 @@ int usb_lowlevel_init(void)
 
 	/* Start the host controller. */
 	cmd = ehci_readl(&hcor->or_usbcmd);
-	/* Philips, Intel, and maybe others need CMD_RUN before the
-         * root hub will detect new devices (why?); NEC doesn't */
+	/*
+	 * Philips, Intel, and maybe others need CMD_RUN before the
+	 * root hub will detect new devices (why?); NEC doesn't
+	 */
 	cmd &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET);
 	cmd |= CMD_RUN;
 	ehci_writel(&hcor->or_usbcmd, cmd);

include/asm-arm/arch-omap3/omap_gpmc.h

@@ -81,4 +81,3 @@
 #endif
 
 #endif /* __ASM_ARCH_OMAP_GPMC_H */
-