There are ways how to call fpga loadmk
1. Full command
fpga loadmk [dev] [address]
2. Dev setup via variable
set fpga [dev]
fpga loadmk [address]
3. Address setup via variable
set fpgadata [address]
fpga loadmk [dev]
4. Dev and address setup via variables
set fpga [dev]
set fpgadata [address]
fpga loadmk
Before this patch only cases 1 and 3 are working but the part of code
was trying to support also cases 2 and 4.
This patch is adding support for cases 2 and 4 to have all of
combinations supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert loadmk command to fpga subcommands. Not all combinations are
working but they have never worked properly. This will be fixed later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Separate dump, load, loadb, loadp and loadbp commands to separate
functions to make it clear how they are called and what parameters they
need.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga info to U_BOOT_CMD_MKENT subcommand.
Also use strtol instead of simple_strtoul. The reason is that if -1 is
passed (or fpga info without "fpga" variable) the list of all fpgas is
shown.
This functionality is in the fpga core but it couldn't be performed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create command wrapper to clean fpga subcommands.
The function logic is taken from cmd_dm.c
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch. Check them
directly when they are read. Also there is no reason to check loadmk
case separately because fpga_data address must be non zero too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parameter checking is dead code because all the time there must be all
params assigned. If they are not assigned there is no 9th parameters
passed and checking before return CMD_RET_USAGE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch before main
one. This patch is simplifying error path and checking parameters right
after assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Incorrect command is already handled and FPGA_NONE should be used only
one. In case of error CMD_RET_USAGE can be returned directly without any
addition logic around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga_get_op() to top of file to remove local function declaration
and also remove useless retyping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clean fpga_get_op() error handling by moving checking/print to do_fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch applied in 2010
"cmd_fpga: cleanup help and check parameters"
(sha1: a790b5b2326be9d7c9ad9e3d9b51a8bfabc62d07"
was adding this checking
+ if (dev == FPGA_INVALID_DEVICE) {
+ puts("FPGA device not specified\n");
+ op = FPGA_NONE;
+ }
which simply broke one command flow which was
setenv fpga <dev>
fpga loadmk <addr> // legacy image
fpga loadmk <addr>:<fit_image_name> //fit image
Also this sequence for FIT image is completely broken
setenv fpga <dev>
setenv fpgadata <addr>:<fit_image_name>
fpga loadmk
(Note: For legacy images this is working fine).
even from code I don't think this has ever worked properly
for fit image (dev = FPGA_INVALID_DEVICE should be rejected
by fpga core). Fit image support was in 2008 added by:
"[new uImage] Add new uImage fromat support to fpga command"
(sha1: c28c4d193d)
Just a summary of these facts that none found this for pretty long time
it shouldn't be a problem to remove this flow (without fpga dev)
completely to simplify the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support to load secure bitstreams(authenticated or
encrypted or both). As of now, this feature is added and tested only
for xilinx bitstreams and the secure bitstream was generated using
xilinx bootgen tool, but the command is defined in more generic way.
Command example to load authenticated and device key
encrypted bitstream is as follows
"fpga loads 0 100000 2000000 0 1"
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the arguments parsing code by parsing
based on requested operation for fpga loadfs and then
parses the most common/basic args for other fpga load
commands. This makes it easy for new command extensions
or additions especially the commands with more args.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that they are in their own directory, we can remove this prefix.
This makes it easier to find a file since the prefix does not get in the
way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.
Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.
Unfortunately, with m68k I get this error:
m68k: + M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o
I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
For case where CMD_FPGA_LOADMK is enabled and GZIP disable.
Warning log:
common/built-in.o: In function `do_fpga':
/mnt/disk/u-boot/common/cmd_fpga.c:218: undefined reference to `gunzip'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
make the use of legacy image format configurable through
the config define CONFIG_IMAGE_FORMAT_LEGACY.
When relying on signed FIT images with required signature check
the legacy image format should be disabled. Therefore introduce
this new define and enable legacy image format if CONFIG_FIT_SIGNATURE
is not set. If CONFIG_FIT_SIGNATURE is set disable per default
the legacy image format.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lars Steubesand <lars.steubesand@philips.com>
Cc: Mike Pearce <mike@kaew.be>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Here is the set of command which has been performed
to proof this feature.
gzip < fpga.bin > fpga.bin.gz
mkimage -A arm -O u-boot -T firmware -C gzip \
-a 20000000 -n "zc702_fpga_bin" -d fpga.bin.gz fpga.bin.gz.ub
tftp 100000 fpga.bin.gz.ub
fpga loadmk 0 100000
This flow should speedup loading bitstream data
from external memory and save image footprint in non volatile
memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This is the main entry point to the FIT image verification code. We will
be using it to handle image verification with signatures, so rename the
function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
In bitstream decoding you can directly check device
which you want to load and in fpga.c are fpga_validate
and fpga_dev_info functions which should be used for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix compiler warning:
cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type
Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
The usage and help for the fpga command is wrong and incomplete,
and the parameters are not checked before to be passed to the
underlying subfunction.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch introduces the following prefix convention for the
image format handling and bootm related code:
genimg_ - dual format shared code
image_ - legacy uImage format specific code
fit_ - new uImage format specific code
boot_ - booting process related code
Related routines are renamed and a few pieces of code are moved around and
re-grouped.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch adds framework for dual format images. Format detection is added
and the bootm controll flow is updated to include cases for new FIT format
uImages.
When the legacy (image_header based) format is detected appropriate
legacy specific handling is invoked. For the new (FIT based) format uImages
dual boot framework has a minial support, that will only print out a
corresponding debug messages. Implementation of the FIT specific handling will
be added in following patches.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
- Add inline helper macros for basic header processing
- Move common non inline code common/image.c
- Replace direct header access with the API routines
- Rename IH_CPU_* to IH_ARCH_*
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Michal Simek
Siva Durga Prasad Paladugu
Tom Rini
Simon Glass
Heiko Schocher
Wolfgang Denk
Stefano Babic
Peter Tyser
Marian Balakowicz