We should run the EFI selftest on both a 32bit and a 64bit ARM platform on
Travis to catch possible errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:
qemu-system-arm -machine virt,highmem=off -bios u-boot.bin
(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
- u-boot.bin loaded and executing in the emulated flash at address 0x0
- A generated device tree blob placed at the start of RAM
- A freely configurable amount of RAM, described by the DTB
- A PL011 serial port, discoverable via the DTB
- An ARMv7 architected timer
- PSCI for rebooting the system
- A generic ECAM-based PCI host controller, discoverable via the DTB
Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:
- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
-net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
-device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Heinrich Schuchardt
Tom Rini
Tuomas Tynkkynen