This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
These two options go together and it is best to do the conversion in one
step. So enable DM_MMC_OPS by default if DM_MMC is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Tom Rini
Simon Glass
Jagan Teki
Peng Fan
Peng Fan