This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
The following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
We use a combination of the serialN alias and CONFIG_CONS_INDEX to
determine which serial alias we should set linux,stdout-path to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The composition of the directory in the drivers/ changed.
I moved SuperH serial driver and marubun PCMCIA driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Marubun pcmcia is a chip for PCMCIA used with SuperH.
Of course, this can be used even by other architectures.
When use this driver, came to be able to use CompactFlash
and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After an error in the AMCC 405EX users manual now correctly configure
IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ
usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese
Michael Schwingen
Gerald Van Baren
Kumar Gala
Jon Loeliger
Nobuhiro Iwamatsu
Wolfgang Denk
Jean-Christophe PLAGNIOL-VILLARD