The core support for the pinctrl drivers for all the UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit c5acf4a2b3 ("pinctrl: Add the concept of peripheral IDs")
added some additional change that was not mentioned in the git-log.
That commit added dm_scan_fdt_node() in the pinctrl uclass binding.
It should be handled by the simple-bus driver or the low-level
driver, not by the pinctrl framework.
I guess Simon's motivation was to bind GPIO banks located under the
Rockchip pinctrl device. It is true some chips have sub-devices
under their pinctrl devices, but it is basically SoC-specific matter.
This commit partly reverts commit c5acf4a2b3 to keep the only
pinctrl-generic features in the uclass. The dm_scan_fdt_node()
should be called from the rk3288_pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The Designware ethernet controller is also seen on PCI bus, e.g.
on Intel Quark SoC. Add this support in the DM version driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce device_is_on_pci_bus() which can be utilized by driver
to test if a device is on a PCI bus.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch addresses some comments raised by Scott in the last versions.
Here the changes in detail:
- Removed __maybe_unused as its not needed
- Added check for strength == 4 and error out for the unsupported
ECC strength values
- Don't set .caclulate, .correct, and .bytes for NAND_ECC_SOFT_BCH as this
will be done in nand_scan_tail()
- Set .caclulate back to fsmc_read_hwecc() in the HW case
- Added comment that this function will only be called on SPEAr platforms,
not supporting the BCH8 HW ECC (FSMC_VER8)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Scott Wood <scottwood@freescale.com>
fdtdec_get_addr_size() hard-codes the number of cells used to represent
an address or size in DT. This is incorrect in many cases depending on
the DT binding for a particular node or property (e.g. it is incorrect
for the "reg" property). In most cases, DT parsing code must use the
properties #address-cells and #size-cells to parse addres properties.
This change splits up the implementation of fdtdec_get_addr_size() so
that the core logic can be used for both hard-coded and non-hard-coded
cases. Various wrapper functions are implemented that support cases
where hard-coded cell counts should or should not be used, and where
the client does and doesn't know the parent node ID that contains the
properties #address-cells and #size-cells.
dev_get_addr() is updated to use the new functions.
Core functionality in fdtdec_get_addr_size_fixed() is widely tested via
fdtdec_get_addr_size(). I tested fdtdec_get_addr_size_auto_noparent() and
dev_get_addr() by manually modifying the Tegra I2C driver to invoke them.
Much of the core implementation of fdtdec_get_addr_size_fixed(),
fdtdec_get_addr_size_auto_parent(), and
fdtdec_get_addr_size_auto_noparent() comes from Thierry Reding's
previous commit "fdt: Fix fdtdec_get_addr_size() for 64-bit".
Based-on-work-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Dropped #define DEBUG at the top of fdtdec.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
milliseconds should be written as 'ms' instead of 'mS'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Marek Vasut <marex@denx.de>
It is not very useful to have the message below on every boot
(especially when we are using early silicon):
U-Boot 2015.10-rc2-23945-g37cf215 (Sep 08 2015 - 14:12:14 -0300)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C)CPU: Thermal invalid data, fuse: 0x0
- invalid sensor device
, so turn the error message into debug level.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Commit 6a13241635 "ci_udc: Update the ci_udc driver to support bulk
transfers" caused the value of "len" to change without updating subsquent
users of that variable in ci_ep_submit_next_request(). This caused the
code that detects when to emit ZLPs (Zero Length Packets) never to
trigger, which in turn caused host timeouts when a ZLP was required,
which in turn broke tests/dfu/, even despite the assertion in that
commit's description that "These changes are tested for both the DFU and
lthor."
Fix this by modifying the added dtd iteration code not to modify "len",
but rather to keep state in a separate variable. Rename the variables
while we're at it so they describe their purpose better.
Fixes: 6a13241635 ("ci_udc: Update the ci_udc driver to support bulk transfers")
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Implement endpoint dequeue callback function.
Without this function, uboot will hang when executing fastboot comamnd.
See following flow:
"fastboot_tx_write_str->fastboot_tx_write->usb_ep_dequeue->ep->ops->dequeue"
without implement ci_udc dequeue function, ep->ops->dequeue is NULL, then
uboot will hang.
Tested on mx6qsabresd board with fastboot enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
When writing to files in a filesystem on MMC, dfu_mmc.c buffers up the
entire file content until the end of the transaction, at which point the
file is written in one go. This allows writing files larger than the USB
transfer size (CONFIG_SYS_DFU_DATA_BUF_SIZE); the maximum written file
size is CONFIG_SYS_DFU_MAX_FILE_SIZE (the size of the temporary buffer).
The current file reading code does not do any buffering, and so limits
the maximum read file size to the USB transfer size. Enhance the code to
do the same kind of buffering as the write path, so the same file size
limits apply.
Remove the size checking code from dfu_read() since all read paths now
support larger files than the USB transfer buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
DFU currently allocates buffer memory at the start of each data transfer
operation and frees it at the end. Especially since memalign() is used to
allocate the buffer, and various other allocations happen during the
transfer, this can expose the code to heap fragmentation, which prevents
the allocation from succeeding on subsequent transfers.
Fix the code to allocate the buffer once when DFU mode is initialized,
and free the buffer once when DFU mode is exited, to reduce the exposure
to heap fragmentation.
The failure mode is:
// Internally to memalign(), this allocates a lot more than s to guarantee
// that alignment can occur, then returns chunks of memory at the start/
// end of the allocated buffer to the heap.
p = memalign(a, s);
// Various other malloc()s occur here, some of which allocate the RAM
// immediately before/after "p".
//
// DFU transfer is complete, so buffer is released.
free(p);
// By chance, no other malloc()/free() here, in DFU at least.
//
// A new DFU transfer starts, so the buffer is allocated again.
// In theory this should succeed since we just free()d a buffer of the
// same size. However, this fails because memalign() internally attempts
// to allocate much more than "s", yet free(p) above only free()d a
// little more than "s".
p = memalign(a, s);
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
By the time g_dnl_unbind() is run, cdev->config has been set to NULL,
so the free() there does nothing, and the config struct is leaked.
Equally, struct usb_gadget contains a linked list of config structs, so
the code should iterate over them all and free each one, rather than
freeing one particular config struct.
composite_unbind() already iterates over the list of config structs, and
unlinks each from the linked list. Fix this loop to free() each struct as
it's unlinked and otherwise forgotten.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present malloc.h is included everywhere since it recently was added to
common.h in this commit:
4519668 mtd/nand/ubi: assortment of alignment fixes
This seems wasteful and unnecessary. We have been trying to trim down
common.h and put separate functions into separate header files and that
change goes in the opposite direction.
Move malloc_cache_aligned() to a new header so that this can be avoided.
The header would perhaps be better named as alignmem.h but it needs to be
included after common.h and people might be confused by this. With the name
memalign.h it fits nicely after malloc() in most cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
The SPEAr600 HW ECC only supports 1-bit ECC strength.
To enable SW BCH4, you need to specify this in your config header:
#define CONFIG_NAND_ECC_BCH
#define CONFIG_BCH
And use the command "nandecc bch4" to select this ECC scheme upon runtime.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Should use FSL_SEC_MON, not CONFIG_FSL_SEC_MON as Kconfig entry.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
port at91_udc driver from linux:
original commit Message:
commit c94e289f195e0e13cf34d27f9338d28221a85751
Author: Arnd Bergmann <arnd@arndb.de>
Date: Sat Apr 11 00:14:21 2015 +0200
usb: gadget: remove incorrect __init/__exit annotations
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for NAND chips with 4KiB page size and 24/1024
ECC strength. Like the Micron MT29F32G08CBACAWP which is used on the
ICnova-A20 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When building dm version of designware eth driver on a platform
with 64-bit phys_addr_t, it reports the following warnings:
drivers/net/designware.c: In function 'designware_eth_probe':
drivers/net/designware.c:599:2:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 3 has type 'phys_addr_t' [-Wformat]
drivers/net/designware.c:600:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/net/designware.c:601:21:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present, until a PCI bus is probed, it cannot be found by its sequence
number unless it has an alias. This is the same with any device.
However with PCI this is more annoying than usual, since bus 0 is always the
same device.
Add a function that tries a little harder to locate PCI bus 0. This means
that PCI enumeration will happen automatically on the first access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit converts pch_gbe ethernet driver to driver model.
Since this driver is only used by Intel Crown Bay board, the
conversion does not keep the non-dm version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
When an EHCI device is registered in device mode, the HW isn't actually
initialized at all, and hence isn't left in a running state. Consequently,
when the device is deregistered, ehci_shutdown() will fail, since the HW
bits it expects to see set in response to its shutdown requests will not
be sent, and the message "EHCI failed to shut down host controller." will
be printed.
Fix ehci-hcd.c to remember whether the device was registered in host or
device mode, and only call ehci_shutdown() for host mode registrations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The dfu tftp feature can be now enabled via Kconfig. This
commit provides necessary code for it.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function allows writing via DFU data stored from fixed buffer address
(like e.g. loadaddr env variable).
Such predefined buffers are used in the update_tftp() code. In fact this
function is a wrapper on the dfu_write() and dfu_flush().
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds initial support for using tftp for downloading and
upgrading firmware on the device.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
After extension of the dfu_get_buf() to also setup (implicitly) the dfu_buf_size
variable it is not needed to set dfu_buf_size to CONFIG_SYS_DFU_DATA_BUF_SIZE.
This variable is set in the dfu_get_buf() by not only considering
CONFIG_SYS_DFU_DATA_BUF but more importantly the "dfu_bufsiz" env variable.
Therefore, dfu_get_buf() should be used for initialization.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.
The case would be to download the images to DDR instead
of flash device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zap variable which is set but never used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
During mmc initialize probe all devices with the MMC Uclass if build
with CONFIG_DM_MMC
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada
Bin Meng
Stefan Roese
Stephen Warren
Fabio Estevam
Adrian Alonso
Peng Fan
Sylvain Lemieux
Heiko Schocher
Simon Glass
Lukasz Majewski
Siva Durga Prasad Paladugu
Marek Vasut
Sjoerd Simons