In current driver, we always copy 4 bytes to the dest memory.
Actually the dest memory may be shorter than 4 bytes.
Add an argument to indicate the dest memory length.
Avoid writing memory outside of the bounds.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In current driver everytime we memcpy 4 bytes to the dest memory
regardless of the remaining length.
This patch adds checking the remaining length before memcpy.
If the length is shorter than 4 bytes, memcpy the actual length of data
to the dest memory.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch fixes the following compile warning:
drivers/spi/fsl_qspi.c: In function 'fsl_qspi_probe':
drivers/spi/fsl_qspi.c:937:15:
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
priv->regs = (struct fsl_qspi_regs *)plat->reg_base;
^
Just make the cast explicit.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According to SD spec, CMD12, CMD52 for writing I/O abort in CCCR need
to be set an Abort command type when they are sent. So, we remove all
chip-specific #ifdefs and make it available for all platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The MMC spec says "It is strongly recommended for hosts to implement
more than 500ms timeout value even if the card indicates the 250ms
maximum busy length." Even the previous value of 300ms is known to
be insufficient for some cards. So, increase the timeout to 500ms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex firmware 9.0 has fixed the issue of
dprc_destroy_container i.e. the used portal is not return to the
free pool. Which was resulting in error ethernet driver want to
use this portal via either DPL or dynamically in Linux.
Hard-coding of portal id is removed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add debug information prints to provide DPMAC statistics
- Number of bytes received
- Number of received and discard frames
- Number of bytes transferred
- Number of frames transferred
etc.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 set the hardware depletion to be 20
buffers in order to support multiple pools in DPNI. This requires
driver to fill the pool with at least 21 to be able to receive
frames. So, Increase number of buffers for a pool.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 puts a new requirement to provide Tx
confirmation and error queue configuration by calling
dpni_set_tx_conf API.
Configure report of only error frames for a tx frame.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Management Complex FW 9.0 puts a new requirement to prepare extended
parameters which should be provided as input in dpni_create. extended
parameters includes traffic class and IP reassembly configurations.
So prepare extended parameters with default "0" as input for
dpni_create.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MC firmware version 9.0.0 contains
- Support of new APIs
- Update in existing APIs
- Change in Major and minor version of DPAA2 objects
This patch contains modifications in FLIB files to support new
MC firmware version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check and compare version of management complex's object with
the version supported by Freescale ldpaa2 ethernet driver.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Current code compares the return pointer of function
qbman_cena_write_start with NULL. Instead the value of the return
pointer should be compared.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Following commit 61bd2f75, exclude unused DDR controller from
calculating RAM size for SPL boot.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the device tree does not specify the EDID pinctrl option for HDMI we
must set it manually. Fix the driver to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some rockchip SoCs include video output (VOP). Add a driver to support this.
It can output via a display driver (UCLASS_DISPLAY) and currently HDMI and
eDP are supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some Rockchip SoCs support embedded DisplayPort output. Add a display driver
for this so that these displays can be used on supported boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some Rockchip SoCs support HDMI output. Add a display driver for this so
that these displays can be used on supported boards.
Unfortunately this driver is not fully functional. It cannot reliably read
EDID information over HDMI. This seems to be due to the clocks being
incorrect - the I2C bus speed appears to be up to 100x slower than the
clock settings indicate. The root cause may be in the clock logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
The displays need to use NPLL and also select some new peripheral clocks.
Add support for these to the clock driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current DisplayPort uclass is too specific. The operations it provides
are shared with other types of output devices, such as HDMI and LVDS LCD
displays.
Generalise the uclass so that it can be used with these devices as well.
Adjust the uclass to handle the EDID reading and conversion to
display_timing internally.
Also update nyan-big which is affected by this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most panels are very simple - they just have a power supply and a backlight.
Add a driver which supports this and implements the enable_backlight()
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
LCD panels can usefully be modelled as their own uclass. They can be probed
(which powers them up ready for use). If they have a backlight, this can be
enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many backlights need to use a PWM to control the brightness. Add a driver
for this. It understands the standard device tree binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
LCD panels normally have a backlight which can be controlled to illuminate
the LCD contents. Add a uclass to support this. Initially it only has a
method to enable the backlight.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a uclass that supports Pulse Width Modulation (PWM) devices. It
provides methods to enable/disable and configure the device.
Signed-off-by: Simon Glass <sjg@chromium.org>
We must use the console name in the 'stdout' variable to select the one
we want. At present the name is formed from the driver name with a suffix
indicating the rotation value.
It seems better to name them sequentially since this can be controlled by
driver order. So adjust the code to use 'vidconsole' for the first,
'vidconsole1' for the second, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
The correct pinctrl is handled automatically so we don't need to do it in
the driver. The exception is when we want to use a different chip select
(other than 0). But this isn't used at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is an incorrect call to rkspi_enable_chip(). It should
be disabling the chip, not enabling it. Correct this and ensure that the
chip is disabled when releasing the bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices need delays before and after activiation. Implement these
features in the SPI driver so that we will be able to enable the Chrome
OS EC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide this method so that 'gpio status' works fully. It now shows
whether a pin is used for input, output or some other function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement this so that the GPIO command will be able to report whether a
GPIO is used for input or output.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file has many features that are not needed by SPL. Use #ifdef to
remove the unused features and reduce the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current method assumes that clocks are numbered from 0 and we can
determine a clock by its number. It is safer to use an ID in the clock's
platform data to avoid the situation where another clock is bound before
the one we expect.
Move the existing code into rk3036 since it still works there. Add a new
implementation for rk3288.
Signed-off-by: Simon Glass <sjg@chromium.org>
Two of the init values are created locally so cannot be out of range.
The masking is unnecessary and in one case is incorrect. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than changing the clock to the same value on every transaction,
remember the last value and don't adjust the clock unless it is necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function adds quite a bit of code to SPL and we probably don't need
all the features in SPL. Add a simple version (for SPL only) to save space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some regulators will not implement any operations (e.g. fixed regulators).
This is not an error, so allow the autoset process to continue when one
of these regulators is found.
Signed-off-by: Simon Glass <sjg@chromium.org>
The currect PMIC debugging is a little confusing. Adjust it so that it is
clear whether the operation succeeded or failed. Also, avoid creating a new
error return value when a perfectly good one is already available.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to be able to find a device before probing it,
perhaps to set up some platform data for it. Allow finding by of_offset
also.
Signed-off-by: Simon Glass <sjg@chromium.org>
GPIO drivers want to be able to show if a pin is enabled for input, output,
or is being used by another function. Some drivers can easily find this
and the code is included in the driver. For some SoCs this is more complex.
Conceptually this should be handled by pinctrl rather than GPIO. Most
pinctrl drivers will have this feature anyway.
Add a method by which a GPIO driver can obtain the pin mux value given a
GPIO reference. This avoids repeating the code in two places.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some boards the pmic interface is useful but the regulator interface
(which comes with it) is too large. Allow them to be separated such that
SPL can decide which it needs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Gong Qianyu
Yangbo Lu
Prabhakar Kushwaha
Pratiyush Mohan Srivastava
Ed Swarthout
Shengzhou Liu
Simon Glass