Within /chosen we may have a node which points to another node, similar
to how /aliases works. Add a helper function to do this lookup.
Signed-off-by: Simon Glass <sjg@chromium.org>
The stdio_dev structure has a private pointer for its creator, but it is
not set up by the serial system. Set it to point to the serial device so
that it can be found by code called by stdio.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some boards board_init() will change GPIOs, so we need to have driver
model available before then. Adjust the board init to arrange this, but
enable it for driver model only, just to be safe.
This does create additional #ifdef logic, but it is safer than trying to
make a pervasive change which may cause some boards to break.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since driver model registers itself with the stdio subsystem, and we
want to avoid delayed registration and other complexity associated with
the current serial console, move the stdio subsystem init earlier when
driver model is used for serial.
This simplifies the implementation. Should there be any problems with
this approach they can be dealt with as boards are converted over to
use driver model for serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to support GPIO access in board_early_init_f() we must set up
driver model before this function is called. In any case, earlier is
better since driver model is (or will become) a key function for most
init.
Signed-off-by: Simon Glass <sjg@chromium.org>
The microblaze-generic board fails to build at least
with the kernel.org crosstool:
https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/
x86_64-gcc-4.9.0-nolibc_microblaze-linux.tar.xz
$ make CROSS_COMPILE=microblaze-linux- microblaze-generic_defconfig all
[ snip ]
CC disk/part.o
CC disk/part_dos.o
LD disk/built-in.o
CC drivers/block/systemace.o
{standard input}: Assembler messages:
{standard input}:2495: Error: operation combines symbols in different segments
{standard input}:2496: Error: operation combines symbols in different segments
{standard input}:2499: Error: operation combines symbols in different segments
{standard input}:2500: Error: operation combines symbols in different segments
{standard input}:2505: Error: operation combines symbols in different segments
{standard input}:2506: Error: operation combines symbols in different segments
{standard input}:2515: Error: operation combines symbols in different segments
{standard input}:2516: Error: operation combines symbols in different segments
{standard input}:2519: Error: operation combines symbols in different segments
{standard input}:2520: Error: operation combines symbols in different segments
{standard input}:2529: Error: operation combines symbols in different segments
{standard input}:2530: Error: operation combines symbols in different segments
{standard input}:2533: Error: operation combines symbols in different segments
{standard input}:2534: Error: operation combines symbols in different segments
{standard input}:2539: Error: operation combines symbols in different segments
{standard input}:2540: Error: operation combines symbols in different segments
{standard input}:2549: Error: operation combines symbols in different segments
{standard input}:2550: Error: operation combines symbols in different segments
make[3]: *** [drivers/block/systemace.o] Error 1
make[2]: *** [drivers/block] Error 2
make[1]: *** [drivers] Error 2
make: *** [__build_one_by_one] Error 2
It looks like the cause of this error message is the "#ident" directive.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
try run => dry run
no nothing => do nothing
"..." => '...'
The last one is for consistency with the other option helps.
Change-Id: I1d69047d1fae6ef095a18f69f44ee13c448db9b7
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
When creating build directories also create parents as necessary. This
fixes a failure when building a hierarchical branch (i.e. foo/bar).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@ti.com>
For an occasional user of patman some failures are not obvious: for
instance when checkpatch reports warnings, the dry run still reports
that the email would be sent. If it is not dry run, the warnings are
shown on the screen, but it is not clear that the email was not sent.
Add some code to report failure to send email explicitly.
Tested by running the script on a patch with style violations,
observed error messages in the script output.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tags like Series-version are normally expected to appear once, and with a
unique value. But buildman doesn't actually look at these tags. So ignore
conflicts.
This allows bulidman to build a branch containing multiple patman series.
Reported-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present buildman naively uses the branch name as part of its directory
path, which causes problems if the name has an embedded '/'.
Replace these with '_' to fix the problem.
Reported-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that buildman supports removing the build directory prefix from output,
add a test for it. Also ensure that output directories are removed when the
test completes.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds coverage of core features of the builder, including the
command-line options which affect building.
Signed-off-by: Simon Glass <sjg@chromium.org>
For reasons that are not well-understood, GetMetaDataForList() can end up
adding to an existing series even when it appears that it should be
starting a new one.
Change from using a default constructor parameter to an explicit one, to
work around this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
For testing it is useful to clean the output directory before running a
test. This avoids a test interfering with the results of a subsequent
test by leaving data around.
Add this feature as an optional parameter to the control logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a build is to be performed, buildman checks to see if it has already
been done. In most cases it will not bother trying again. However, it was
not reading the return code from the 'done' file, so if the result was a
failure, it would not be counted. This depresses the 'failure' count stats
that buildman prints in this case.
Fix this bug by always reading the return code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than reading boards.cfg, which may take time to generate and is not
necessarily suitable for running tests, create our own list of boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
These files may not exist in the environment, or may not be suitable for
testing. Provide our own config file and our own toolchains when running
tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the bsettings code back to the main buildman.py file, so we can do
something different when testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Buildman currently lacks testing in many areas, including its use of git,
make and many command-line flags.
Add a functional test which covers some of these areas. So far it does
a fake 'build' of all boards for the current source tree.
This version reads the real ~/.buildman and boards.cfg files. Future work
will improve this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test point for the command module. This allows tests to emulate
the execution of commands. This provides more control (since we can make
the fake 'commands' do whatever we like), makes it faster to write tests
since we don't need to set up as much environment, and speeds up test
execution.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to issue parser commands from within buildman for test
purposes. Move the parser code into its own file so we don't end up needing
the buildman and test modules to reference each other.
Signed-off-by: Simon Glass <sjg@chromium.org>
RunPipe() currently pipes the output of stdout and stderr to a pty, but
this is not the intended behaviour. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the basic test so that it checks all console output. This will help
to ensure that the builder is behaving correctly with printing summary
information.
Signed-off-by: Simon Glass <sjg@chromium.org>
To allow us to verify the builder's console output, send it through a
function which can collect it when running in test mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running unit tests we don't want output to go to the terminal.
Provide a way of collecting it so that it can be examined by test code
later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit fa9c021632 ("mx6: add example DTB for mx6qsabreauto") introduced
'imx6q-sabreauto.dts' but it adds no real value as the dts file only contains
the 'model' and 'compatible' strings.
After this commit the final binary is also changed from 'u-boot.imx' to
'u-boot-dtb.imx', which may confuse users.
So revert it until a more complete and useful device tree could be provided.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
nitrogen6x.h file defines CONFIG_CMD_FS_GENERIC, so we are able to use generic
'load' command instead of 'fatload'. It allows to use ext filesystem and keep
compatibilty with fat filesystem.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
Currently mx6dlsabresd shares the same DCD settings with the nitrogen board.
Provide a DCD configuration file specific to mx6dlsabresd with the settings
recommended by the Freescale hardware team.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
UART does not use the UART FIFO, but we should also not rely that
the UART FIFO is diabled by default. For instance, when loading
U-Boot using the boot ROMs serial downloader protocol over UART,
FIFO is enabled at U-Boot start time.
This patch disables the RX and TX FIFO, sets back their thresholds
and flushes them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The status register 1 (S1) is not writeable, hence we should not
write it. In order to clear the RDRF flag we only need to read
the data register.
Also, when stressing U-Boot a lot with serial input, an overflow can
occur which asserts the S1_OR flag (while not asserting the S1_RDRF
flag). To clear this flag we again just need to read the data
register, hence add this flag to the abort conditions for the while
loop.
Insert a compiler barrier to make sure reading the data register
gets executed after reading the status register.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The load region size of EIM-NOR are defined to 0. For this case,
the parameter "imximage_init_loadsize" must be calculated.
The imximage tool implements the calculation in the "imximage_generate"
function, but the following function "imximage_set_header" resets the value
and not calculate. This bug cause some fields of IVT head are not
correct, for example the boot_data and DCD overlay the application area.
Signed-off-by: Ye.Li <B37916@freescale.com>
The Latency parameters of PL310 Tag RAM latency control register and
Data RAM Latency control register are set in L2 cache enable. And
setting these registers must have PL310 NOT enabled.
But when using Plugin mode boot, the PL310 is enabled by bootrom.
The patch disables the PL310 before applying this setting.
Signed-off-by: Ye.Li <Ye.Li@freescale.com>
The leds array within struct ventana has space for 3 elements, but the
setup_board_gpio() function tries to set up 4 GPIOs for LEDs. Recent
versions of GCC complain about that:
board/gateworks/gw_ventana/gw_ventana.c: In function 'setup_board_gpio':
board/gateworks/gw_ventana/gw_ventana.c:987:27: warning: iteration 3u invokes undefined behavior [-Waggressive-loop-optimizations]
if (gpio_cfg[board].leds[i])
^
board/gateworks/gw_ventana/gw_ventana.c:986:2: note: containing loop
for (i = 0; i < 4; i++) {
^
Fix this by making the upper bound of the loop match the array size.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
According to mx53 and mx6 reference manuals:
"The maximum size of the DCD limited to 1768 bytes."
As each DCD entry consists of 8 bytes, we have a total of 1768 / 8 = 221, and
excluding the first entry, which is the header leads to 220 as the maximum
number for DCD size.
Reported-by: Jonas Karlsson <jonas.d.karlsson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Simon Glass
Tom Rini
Masahiro Yamada
Thierry Reding
Vadim Bendebury
Fabio Estevam
Guillaume GARDET
Stefan Agner
Nikolay Dimitrov
Ye.Li
Tim Harvey
Nikita Kiryanov