UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h
PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Fix the comment to reflect the actual function call time.
Change the printf message to look nicer in the context it might be printed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Remove old o2dnt board without OF support. New support for this board
is added by the previous patch, O2I configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add common code for o2dnt and o2dnt2 based boards and add different
board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and
O3DNT boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.
For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.
Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.
Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.
Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.
Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
This code will also be used before reallocation and during this time we
are not allowed to do these printings.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
This enables I2C support on smdk5250.
Pinmux setting moved to board file to avoid repeated setting of
gpio lines.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
This fixes:
cmd_bc3450.c:55:0: warning: "CONFIG_SYS_CPU" redefined [enabled by default]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
In commit 1a89a217f5 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured. This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.
Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.
(Reworded by Tom Rini to be more precise about what the problem was)
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
- enable OF control and embedded OF
- set default device tree file name to 'microblaze'
- add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
- add an empty but processable dts for microblaze-generic
Signed-off-by: Stephan Linz <linz@li-pro.net>
When Trimslice is booted from serial flash, the boot ROM does this, so
U-Boot doesn't need to. However, booting from the SD slot for recovery
purposes, the boot ROM does not set up the pinmux for serial flash. Add
code to U-Boot to set this up, so that an SD-based recovery U-Boot image
can upgrade the U-Boot in serial flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards can override this to set up the pinmux correctly to access serial
flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
GPIO PI6 can be used to obtain the write-protect status of an SD card
inserted into the SD slot.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
Enable data cache with 1:1 mapping of DDR to enable fast file
transfer over tty which was doing lot of copy.
This feature is enabled only for flashing operation i.e. when
CONFIG_SPEAR_USBTTY is enabled.
This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation
boards.
Following figures show an estimate on the performance improvements. The
test setup was a Linux host (not Windows) and involved measurement of
only binary transfer time, through kermit. The flash erase and flash
copy time would be unaffected by these patches.
Another thing is this that the timings remained more or less same across
ARM9 and Cortex based devices, hence reporting only one of the cases.
Before Enhancements
===================
$ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m41.228s
user 0m0.002s
sys 0m0.064s
After Enhancements
==================
$ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m5.441s
user 0m0.001s
sys 0m0.001s
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.
SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ethaddr can be optionally read from i2c memory. So, chip_config command supports
reading/writing hw mac id into i2c memory. Placing this code within
CONFIG_CMD_NET as this would only be needed when network interface is configured
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
While the u-boot code is running from the flash, it is essential that no access
is made to the bss segment. This is due to the fact that .rel.dyn and .bss areas
overlap and former contains information used in relocation. In SPEAr, this was
not taken into consideration. As a result, while the relocation wasn't complete,
dram_init populated an uninitialized global variable resulting in corruption of
.rel.dyn area, which resulted in u-boot crash.
This commit fixes this problem by removing code that accesses bss segment
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Steve Sakoman
Stefano Babic
Igor Grinberg
Sughosh Ganu
Stefan Roese
Anatolij Gustschin
Jens Scharsig
Hongtao Jia
Shaohui Xie
Timur Tabi
Matthew McClintock
Gerlando Falauto
Holger Brunck
Rajeshwari Shinde
Troy Kisky
Wolfgang Denk
SRICHARAN R
Fabio Estevam
Stephan Linz
Stephen Warren
Tom Warren
Thierry Reding
Peter Meerwald
Michal Simek
esw@bus-elektronik.de
Shiraz Hashim
Amit Virdi
Vipin KUMAR