This patch creates a flexible parser for Ethernet Switch
configurations that should support complex commands.
The parser searches for predefined keywords in the command
and calls the proper function when a match is found.
Also, the parser allows for optional keywords, such as
"port", to apply the command on a port
or on all ports. For now, the defined commands are:
ethsw [port <port_no>] { enable | disable | show }
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
At startup, the default configuration should be:
- enable HW learning on all ports (HW default);
- all ports are VLAN aware;
- all ports are members of VLAN 1;
- all ports have Port-based VLAN 1;
- on all ports, the switch is allowed to remove
maximum one VLAN tag,
- on egress, the switch should add a VLAN tag if the
frame is classified to a different VLAN than the port's
Port-based VLAN;
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These new operations allow manipulation of bitfields
within a word by using a mask instead of width and
shift values to extract/replace the bitfields.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The VSC9953 DS reserves a register between vlan_mask and anag_efil
registers.
Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and default bit values). This patch fixes this issue
by changing the value of the define used to enable the port and
assures that no other bits are changes by replacing out_le32()
with setbits_le32().
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "port_no",
puts each variable declaration on a line and removes
unnecessary tabs.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check maximum ecc strength for each platfrom to avoid the calculated ecc
exceed the limitation.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Han Xu <b45815@freescale.com>
Tested-By: Tim Harvey <tharvey at gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
We have defined this kconfig entry in arch/arm/cpu/armv7/mx7/Kconfig,
no need to redefine it in board Kconfig.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
drop select CPU_V7 for board target, since ARCH_MX7 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
get_board_rev() is not actually providing the board revision.
It just returns the CPU revision instead.
As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_board_rev() is not actually providing the board revision.
It just returns the CPU revision instead.
As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Include <usb/ehci-fsl.h> in order to fix the following sparse warning:
board/freescale/mx7dsabresd/mx7dsabresd.c:538:5: warning: symbol 'board_ehci_hcd_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We use trigger pmic reset to reset the board, so set bit SRS to
disable internal WDOG_RESET_B_DEB to make reset stable.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
We should not simple use "writew(WCR_WDE, &wdog->wcr)" to set
wcr, since this will override bits set before reset_cpu.
Use clrsetbits_le16 instead of writew to fix this issue.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
When setting iomux for a pin mux, there is no need to check mux_ctrl_ofs.
Also If still checking mux_ctrl_ofs, we have no chance to set iomux
for i.MX7D IOMUXC_LPSR_SW_MUX_CTL_PAD_GPIO1_IO00, because the mux_ctrl_ofs
for this register is 0.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit c5acf4a2b3 ("pinctrl: Add the concept of peripheral IDs")
added some additional change that was not mentioned in the git-log.
That commit added dm_scan_fdt_node() in the pinctrl uclass binding.
It should be handled by the simple-bus driver or the low-level
driver, not by the pinctrl framework.
I guess Simon's motivation was to bind GPIO banks located under the
Rockchip pinctrl device. It is true some chips have sub-devices
under their pinctrl devices, but it is basically SoC-specific matter.
This commit partly reverts commit c5acf4a2b3 to keep the only
pinctrl-generic features in the uclass. The dm_scan_fdt_node()
should be called from the rk3288_pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Quark SoC does not support MSR MTRRs. Fixed and variable range MTRRs
are accessed indirectly via the message port and not the traditional
MSR mechanism. Only UC, WT and WB cache types are supported.
We configure all the fixed range MTRRs with common values (VGA RAM
as UC, others as WB) and 3 variable range MTRRs for ROM/eSRAM/RAM as
WB, which significantly improves the boot time performance.
With this commit, it takes only 2 seconds for U-Boot to boot to shell
on Intel Galileo board. Previously it took about 6 seconds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Desktop Management Interface (DMI) is not supported by U-Boot now.
Add it to the TODO list.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Document porting considerations for Intel Quark based board,
including MRC parameters and PCIe initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now we have enabled PCIe root port on Quark SoC, add its PIRQ
routing information in the device tree as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Thermal sensor on Quark SoC needs to be properly initialized per
Quark firmware writer guide, otherwise when booting Linux kernel,
it triggers system shutdown because of wrong temperature in the
thermal sensor is detected by the kernel driver (see below):
[ 5.119819] thermal_sys: Critical temperature reached(206 C),shutting down
[ 5.128997] Failed to start orderly shutdown: forcing the issue
[ 5.135495] Emergency Sync complete
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When Linux kernel boots, it hangs at:
[ 0.829408] Intel Quark side-band driver registered
This happens when Quark kernel Isolated Memory Region (IMR) driver
tries to lock an IMR register to protect kernel's text and rodata
sections. However in order to have IMR function correctly, HMBOUND
register must be locked otherwise the system just hangs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change existing codes to use clrbits, setbits, clrsetbits macros.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On Intel Quark, lots of registers on the message port need be
programmed. Add handy clrbits, setbits, clrsetbits macros for
message port access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Not like other Intel Ethernet controllers (e.g.: E1000), Intel Quark
SoC integrated designware Ethernet controller does not have a chipset
defined way to store/restore mac address. Enable random mac address
so that we can use Ethernet even without 'ethaddr'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert to use DM version of Designware ethernet driver on Intel
quark/galileo.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Designware ethernet controller is also seen on PCI bus, e.g.
on Intel Quark SoC. Add this support in the DM version driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce device_is_on_pci_bus() which can be utilized by driver
to test if a device is on a PCI bus.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
These properties are necessary to use full-featured pinctrl drivers
in SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence"). The Tegra114 TRM doesn't contain this information, but
the programming of PLLC is the same on Tegra114 and Tegra124.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence").
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the SPI controllers found on Tegra20 SOCs.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While clk_m and the oscillator run at the same frequencies on Tegra114
and Tegra124, clk_m is the proper source for the architected timer. On
more recent Tegra generations, Tegra210 and later, both the oscillator
and clk_m can run at different frequencies. clk_m will be divided down
from the oscillator.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Codrin Ciubotariu
Otavio Salvador
Heiko Schocher
Peng Fan
Fabio Estevam
Masahiro Yamada
Tom Rini
Bin Meng
Thierry Reding
Mirza Krak