Disable a few things which interfere with the EFI init. This allows QEMU to
to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is running from EFI some of the x86 init is replaced with
EFI-specific init. For example, since DRAM has already been set up, we only
need to find it, not init it. Add these functions so that boards can easily
allow booting from EFI if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot runs as an EFI payload it needs to avoid setting up the CPU
again. Also U-Boot currently does not handle interrupts for many devices, so
run with interrupts disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.
Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than add these as open-coded values, create an enum with the commonly
used flags.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for building a 32/64-bit EFI stub for x86. This involves
building the startup and relocation code for either i386 or x86_64.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to load U-Boot onto a board even if is it already
running EFI. This can allow access to the U-Boot command interface, flexible
booting options and easier development.
The easiest way to do this is to build U-Boot as a binary blob and have an
EFI stub copy it into RAM. Add support for this feature, targeting 32-bit
initially.
Also add a way to detect when U-Boot has been loaded via a stub. This goes
in common.h since it needs to be widely available so that we avoid redoing
initialisation that should be skipped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a linker script and relocation code for building 64-bit EFI
applications. This can be used for the EFI stub.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code currently requires CONFIG_SYS_TEXT_BASE but this should be
unnecessary. As a first step, remove the build-time limitation and report an
error instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This contains just enough to bring up the serial UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add support for the efi-x86 board, which supports running U-Boot as an
EFI 32-bit application.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bring in this file from Linux 4.1. It supports relocation features specific
to x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application we must skip relocation. Add support for
this in the x86 relocation code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the toolchain flags to build U-Boot as a relocatable shared library,
as required by EFI.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application, U-Boot must request memory from EFI,
and provide access to the boot services U-Boot needs.
Add library code to perform these tasks. This includes efi_main() which is
the entry point from EFI. U-Boot is built as a shared library.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 the global_data pointer is provided through a somewhat-bizarre and
x86-specific mechanism: the F segment register is set to a pointer to the
start of global_data, so that accesses can use this build-in register.
When running as an EFI application we don't want to mess with the Global
Descriptor Table (GDT) and there is little advantage (in terms of code size)
to doing so.
Allow global_data to be a simple variable in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, remove an unused field and make sure to use existing #define
constants instead of open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The GDT works but technically the length is incorrect. Fix this and add a
comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is now handled by generic U-Boot code so we do not need an x86 version.
It is no-longer called, so remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These flags now overlap some global ones. Adjust the x86-specific flags to
avoid this. Since this requires a change to the start.S code, add a way for
tools to find the 32-bit cold reset entry point. Previously this was at a
fixed offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix a typo, improve some comments and add a little more detail in some
cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the microcode blob for BayTrail-I B0 stepping,
CPUID signature 30671h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
BayTrail FSP Gold4 release adds one UPD parameter to control IGD
enable/disable.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
When running SMP configuration on QEMU (tcg mode, no kvm), there is
a busy loop in start_aps(), calling udelay(), that waits for APs to
show up online. However, there is a chance that VCPU1 will be timeout
waiting, IOW the secondary VCPUs haven't started their execution yet.
This patch adds a 'pause' instruction in __udelay() only for QEMU
target, to give other VCPUs a chance to run. When QEMU sees the
'pause' instruction, it will yeild the execution to other CPUs.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL's cache line size is 64bytes, need to
define the macro CONFIG_SYS_CACHELINE_SIZE to 64 for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Update imx register base address for i.MX6UL.
2. Remove duplicated MXS_APBH/GPMI/BCH_BASE.
3. Remove #ifdef for register addresses that equal to
"AIPS2_OFF_BASE_ADDR + 0x34000" for different chips.
4. According fuse map, complete fuse_bank4_regs.
5. Move AIPS3_ARB_BASE_ADDR and AIPS3_ARB_END_ADDR out of #ifdef CONFIG_MX6SX,
because we can use runtime check
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime from
DIGPROG register. But the value has been occupied by MXC_CPU_MX6D which
is not real id from DIGPROG register, so change i.MX6D to value 0x67 which
was not occupied.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Simon Glass
Ben Stoltz
Bin Meng
Miao Yan
Nikhil Badola
Wang Dongsheng
Peng Fan
Nikita Kiryanov