This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip. The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
- Update the local bus ranges in the FDT for Linux for the various
devices connected to the local bus via chip-select.
- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
lower than 66 MHz and uses I/O accessor functions consequently.
- UPM data update.
- Update of default environment and configuration. Use I2C multibus
as we do have two I2C buses. Also enable sdram and ext2 commands.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch replaces the BOARD_REVISION variable in include/config.mk
by a using a temporary include file in the platform directory.
The former way does not work anymore and the latter is also used by
some other boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver,
because I have no longer access to the hardware.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch provides an unificated way of handling xilinx v5 ppc440 boards.
It unificates 3 different things:
1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.
If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).
2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)
3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.
In order to support new boards they can be implemented in the next way:
a) Simple Generic Board (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config
&& make
b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile
c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507
Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:
Cheap board by Avnet for evaluating the Virtex5 FX technology.
This patch adds support for:
- UartLite
- 16MB Flash
- 64MB RAM
Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds initdram() to DASA_SIM boards that has been
removed accidentally by a previous commit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some direct references to common/lists.o from some
esd linker scripts. This is necessary because the lists source was moved
and is not in the "common" directory anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes initdram() and testdram() from most esd 405 platforms.
Some boards also have an empty dummy implementation of
misc_init_f(). This is also removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removed the obsolete initdram() function from
VOM405 platform file.
Some minor cleanup.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch
- wraps some long lines
- removes unused/obsolete functions: misc_init_f() and initdram()
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.
Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200
Removed initialization of controller from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses. Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
- memsetup.s is changed/merged to lowlevel_init.S
memsetup.S has a global label memsetup that just returns back to caller
- memsetup global label is changed/merged to lowlevel_init
This label is not called from anywhere.
Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
Graeme Russ
Anatolij Gustschin
Detlev Zundel
Timur Tabi
Wolfgang Denk
Jean-Christophe PLAGNIOL-VILLARD
Sergei Poselenov
Stefan Roese
Matthias Fuchs
Kyungmin Park
Heiko Schocher
Ricardo Ribalda Delgado
Ben Warren
Andy Fleming
Nobuhiro Iwamatsu
Guennadi Liakhovetski
Gururaja Hebbar K R