Adds mmc_rpmb_route_frames() to route RPMB data frames from/to an
external entity.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of manually specifying CONFIG_SYS_EXTRA_ENV_RELOC
for every board that needs it, it shouldn't hurt to let
initr_reloc_global_data() always relocate gd->env_addr
unless we know this pointer is outside the initial binary.
To achieve this, the relocation is omitted if
CONFIG_ENV_ADDR is defined (and ENV_IS_EMBEDDED is not).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message:
45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds support for Gigadevices SPI NAND device to the new SPI
NAND infrastructure in U-Boot. Currently only the 128MiB GD5F1GQ4UC
device is supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Jagan Teki <jagan@openedev.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).
By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.
Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.
This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
include/mtd.h might be included by files even if CONFIG_DM is not
enabled. In this case, the call to dev_get_uclass_priv() would trigger
a build error. Because this helper has no user, let's drop it off.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
While trying to enable the dw_mmc on rk3188 I managed to confuse
and hang the dw_mmc controller into not delivering further data.
The fifo state never became ready and the driver was iterating in
the while loop reading 0-byte packets forever.
So inspired by how other implementations handle this, check the fifo-
state beforhand and add a timeout to catch any glaring fifo issues
without hanging uboot altogether.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Remove duplicated inclusion of dm/ofnode.h
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
The comment references a structure name that doesn't exist. Use
the name of the actual uclass.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
We might want to access data stored onto one wire EEPROMs.
Create a framework to provide a consistent API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked patch]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add a function to find the block device descriptor of the parent
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[trini: Move function declaration to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date: Wed May 16 14:38:08 2018 +0300
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
Note:
- Update sun7i-a20-primo73.dts as per Linux, since
this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
added for this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532
Author: Pascal Roeleven <dev@pascalroeleven.nl>
Date: Fri Apr 20 12:21:12 2018 +0200
ARM: dts: sun4i: Fix incorrect clocks for displays
Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts
like other dts file since there dts file are U-Boot specific.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
video_init, video_putc and video_puts functions are not implemented
anywhere, remove their declaration from the header.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a unit test assert-method, which compares two given memory areas for
byte-wise equality.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some devices offer a text-based OSD (on-screen display) that can be
programmatically controlled (i.e. text displayed on).
Add a uclass to support such devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The EFI subsystems needs to know the size of the terminal. If the
environment variable
stdout = serial,vidconsole
this size cannot be read from the video console. So the EFI subsystem
sends escape sequences to read the size. With this patch we get support
for the following escape sequences:
ESC "7" Save cursor position
ESC "8" Restore cursor position
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Only add CONFIG_DISPLAY to defconfig because CONFIG_I2C_EDID
is automatically selected by CONFIG_DISPLAY
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option has never been used for anything. Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
These options are not used or necessary when device model is being used
for SCSI. Just drop them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
The arm, xtensa and mips version of atomic.h were already very similar
(the mips one was a copy of xtensa). Combine these implementations
together to produce a generic atomic.h that can be included by these
architectures (and any others that need it in future).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.
A few parts were borrowed from the Linux kernel driver.
Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Add support to check for this condition and use the
detected phy address when its safe to do so.
Also, add a public API that exposes the phy address of
a given slave. This can be used to update device-tree that
is passed to Linux kernel.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Jens Wiklander
Adam Ford
Simon Goldschmidt
Alexey Brodkin
Kever Yang
Stefan Roese
Marek Vasut
Bin Meng
Miquel Raynal
Heiko Stuebner
Liviu Dudau
Mario Six
Eugen Hristev
Maxime Ripard
Tien Fong Chee
Jagan Teki
Heinrich Schuchardt
Ran Wang
Priyanka Jain
Pramod Kumar
Nipun Gupta
Luis Araneda
Michal Simek
Tuomas Tynkkynen
Chris Packham
Quentin Schulz
Sekhar Nori