We handle i2c_write return code and complain in case of error. We propagate the
error, too, to allow better handling at the upper level in the future.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
We add a return code to wait_for_bb() to be able to report errors to the
callers properly. We in turn handle this new error code in i2c_read, i2c_write
and i2c_probe.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Added posted writes (read after writes) to effect the
change immediately for channel confiuration and channel
enable register
Disable the channel to purge receieve data in TX_ONLY
mode transfer otherwise rx data will get affected by
the next immediate RX_ONLY mode transfer
Wait for the EOT bit to be set after last byte has been
loaded to TX shift register in the the TX_ONLY mode.This
ensures TX data has been completely shifted out
Disable the channel in RX_ONLY mode before reading the
last data from RXX register to prevent the SPI slave
to transmit next word
Signed-off-by: Ajoy Kumar Das <akdas75@yahoo.in>
Cc: Tom Rini <trini@ti.com>
Cc: jacopo mondi <j.mondi@voltaelectronics.com>
DMM_LISA_MAP registers program whether memory is mapped
on particular EMIF or not. Irrespective of these registers
EMIF is getting configured. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Git commit d417d1db5f replaced the
omap-common file reset.S with reset.c, but the Makefile was not
adjusted for that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
AM33XX with BCH8 can't work with nand_spl_simple correctly
because custom read_page implementation is required for proper
syndrome generation.
This simple driver mostly duplicates nand_spl_simple but has
nand_read_page changed to suit our needs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds support for BCH8 error correction code to omap_gpmc
driver. We use GPMC to generate codes/syndromes but we need ELM to find
error locations from given syndrome.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
[ilya: merge it with omap_gpmc driver, some fixes and cleanup]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Include asm/arch/sys_proto.h for gpmc_init prototype.
Without this we get a warning while building for AM335x.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954
removed the need for these definitions but missed to remove them.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
This patch fix following errors
universal.c: In function 'init_pmic_lcd':
universal.c:340: warning: implicit declaration of function 'get_pmic'
universal.c:340: warning: initialization makes pointer from integer without a cast
universal.c: In function 'lcd_power_on':
universal.c:431: warning: initialization makes pointer from integer without a cast
universal.c: At top level:
universal.c:335: warning: 'init_pmic_lcd' defined but not used
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
Fix several warnings when enabling UBIFS on MIPS:
In file included from ubifs.h:2137:0,
from ubifs.c:26:
misc.h: In function 'ubifs_zn_dirty':
misc.h:38:2: warning: passing argument 2 of 'test_bit' discards 'const' qualifier from pointer target type [enabled by default]
../include/asm/bitops.h:569:23: note: expected 'volatile void *' but argument is of type 'const long unsigned int *'
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If bal is 8 bytes aligned, the _gp will not be 8 bytes aligned.
then the following ld insntrustion generates a Adel exception.
So here make _gp be always aligned in 8 bytes.
Signed-off-by: Zhi-zhou Zhang <zhizhou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The filename buffer is allocated dynamically. It must be cache aligned.
Moreover, it is necessary to erase its content before we use it for
file name operations.
This prevents from corruption of written file names.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The device block descriptor (block_dev_desc_t) )shall be stored at
ext4 early code (at ext4fs_set_blk_dev in this case) to be available
for latter use (like put_ext4()).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The ext4write code has been using direct calls to 64-32 division
(/ and %).
Officially supported u-boot toolchains (eldk-5.[12].x) generate calls
to __aeabi_uldivmod(), which is niether defined in the toolchain libs
nor u-boot source tree.
Due to that, when the ext4write command has been executed, "undefined
instruction" execption was generated (since the __aeabi_uldivmod()
is not provided).
To fix this error, lldiv() for division and do_div() for modulo have
been used.
Those two functions are recommended for performing 64-32 bit number
division in u-boot.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
If the pl011 is connected to another device which has hardware
flow-control on, characters are never received by the pl011.
Asserting RTS when flow-control is off will have no effect.
This is in line with how Linux behaves.
Signed-off-by: Joshua Housh <joshua.housh@calxeda.com>
Tested-by: Marek Vasut <marex@denx.de>
Use a generic 'dram_vals[]' array that has the full initialization
sequence and rename the initialization method so it doesn't has a
frequency on its name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The config is current broken. It compiles but does not boot because IDE is
enabled. Remove all IDE options, and enable SCSI instead.
Also add a working boot command and Linux bootargs, and enable command
line editing to make it easier to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows u-boot to figure out the partitions of a chrome-os install.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not intended to be exported from the video drivers, so
remove the prototype. This fixes an error:
cfb_console.c:1793:12: error: static declaration of 'video_init' follows non-static declaration
Signed-off-by: Simon Glass <sjg@chromium.org>
This command will start erasing at memory address zero
if there is not a valid framebuffer address that was found
during video_init().
This is a common case with Chrome OS devices in normal mode
when we do not execute the video option rom in coreboot.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The function setup_pcat_compatibility() is weak and implemented as empty
function in board.c hence we don't have to override that with another
empty function.
monitor_flash_len is unused, drop it.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
... because that information is already "encoded" in the directory name.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some systems (like Google Link device) provide the ability to keep a
history of the target CPU port80 accesses, which is extremely handy
for debugging. The problem is that the EC handling port 80 access is
orders of magnitude slower than the AP. This causes random loss of
trace data.
This change allows to throttle port 80 accesses such that in case the
AP is trying to post faster than the EC can handle, a delay is
introduced to make sure that the post rate is throttled. Experiments
have shown that on Link the delay should be at least 350,000 of tsc
clocks.
Throttling is not being enabled by default: to enable it one would
have to set MIN_PORT80_KCLOCKS_DELAY to something like 400 and rebuild
the u-boot image. With upcoming EC code optimizations this number
could be decreased (new new value should be established
experimentally).
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some u-boot modules rely on availability of get_ticks() and
get_tbclk() functions, reporting a free running clock and its
frequency respectively. Traditionally these functions return number
and frequency of timer interrupts.
Intel's core architecture processors however are known to run the
rdtsc instruction at a constant rate of the so called 'Max Non Turbo
ratio' times the external clock frequency which is 100MHz. This is
just as good for the timer tick functions in question.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This will write magic value to APMC command port which
will trigger an SMI and cause coreboot to lock down
the ME, chipset, and CPU.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Vincent Stehlé
Nikita Kiryanov
Thomas Weber
Yegor Yefremov
Stefano Babic
Davide Bonfanti
ajoy
Lokesh Vutla
Robert P. J. Day
Peter Barada
Ilya Yanok
Mansoor Ahamed
Andreas Bießmann
Minkyu Kang
Daniel Schwierzeck
Zhi-zhou Zhang
Tom Rini
Łukasz Majewski
Luka Perkov
Joshua Housh
Otavio Salvador
Simon Glass
Gabe Black
Duncan Laurie
Stefan Reinauer
Vadim Bendebury