Add lpuart support using the driver model.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MC firmware version 9.0.0 contains
- Support of new APIs
- Update in existing APIs
- Change in Major and minor version of DPAA2 objects
This patch contains modifications in FLIB files to support new
MC firmware version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are two phases in Secure Boot
1. ISBC: In BootROM, validate the BootLoader (U-Boot).
2. ESBC: In U-Boot, continuing the Chain of Trust by
validating and booting LINUX.
For ESBC phase, there is no difference in SoC's based on ARM or
PowerPC cores.
But the exit conditions after ISBC phase i.e. entry conditions for
U-Boot are different for ARM and PowerPC.
PowerPC:
If Secure Boot is executed, a separate U-Boot target is required
which must be compiled with a diffrent Text Base as compared to
Non-Secure Boot. There are some LAW and TLB settings which are
required specifically for Secure Boot scenario.
ARM:
ARM based SoC's have a fixed memory map and exit conditions from
BootROM are same irrespective of boot mode (Secure or Non-Secure).
Thus the current Secure Boot functionlity has been split into
two parts:
CONFIG_CHAIN_OF_TRUST
This will have the following functionality as part of U-Boot:
1. Enable commands like esbc_validate, esbc_halt
2. Change the environment settings based on bootmode, determined
at run time:
- If bootmode is non-secure, no change
- If bootmode is secure, set the following:
- bootdelay = 0 (Don't give boot prompt)
- bootcmd = Validate and execute the bootscript.
CONFIG_SECURE_BOOT
This is defined only for creating a different compile time target
for secure boot.
Traditionally, both these functionalities were defined under
CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement
for a separate Secure Boot target for ARM based SoC's.
CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be
determine at run time.
Another Security Requirement for running CHAIN_OF_TRUST is that
U-Boot environemnt must not be picked from flash/external memory.
This cannot be done based on bootmode at run time in current U-Boot
architecture. Once this dependency is resolved, no separate
SECURE_BOOT target will be required for ARM based SoC's.
Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is
defining CONFIG_ENV_IS_NOWHERE
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The file fsl_secure_boot.h must be included in config file for
Secure Boot. This is not required to be protected by any macro.
CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be
turned on.
The above was missing in some config files and all files have been
made uniform in this respect.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Define auto negotiation timeout as 20secs
the default 4secs might not be sufficient
always and hence defined for worst case.
It is observed that autoneg takes moretime
if connected to outside network and hence
increase it to 20secs.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont use shortcut command for setenv as
it wont work now due introduction of new
command setexpr.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify DFU commands to use latest kernel offsets and sizes
as per modified partitions in the linux device tree.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs from EL3 system timer is setup based on this macro.
Software default freq for silicon is 100MHz but enable opton to rewrite
it. Emulation platform is using 4MHz.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected
U-Boot using sdboot1 variable which refers to mmc dev 1.
But this device doesn't exist because only one controller is available.
This patch fix logic around sdboot mode with using sdbootdev internal
variable.
Reported-by: Chris Kohn <ckohn@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link to zynqmp common file is incorrect. Fix it by removing the whole
link because it is visible from the file where to look at it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define minimum sdhci frequency for ep, as not defining
it causes the divisor to be 2048 as per sd version but
keeping clock very low on ep causes command failures.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add bitstream type BIT_NONE to the bitstream type
enum. This might be useful while loading bitstreams
in respective drivers.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To solve enabling ETH_DM where ksz90x1_reg_field is defined only when
additional Micrel type is defined.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc405 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc440 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Gong Qianyu
Wenbin Song
Prabhakar Kushwaha
Aneesh Bansal
Ricardo Ribalda Delgado
Siva Durga Prasad Paladugu
Michal Simek
Michal Simek