The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Currently we have the following behavior in ehci_hcd_init()
- Read csmr1 register, clear bit 26 and then set bit 26.
However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.
Moreover more descriptive names were chosen for relevant fields.
Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.
Tested at: Trats - Exynos4210
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
The existing USB configuration parsing code relies on the descriptors'
own length values when reading through the configuration blob. Since the
size of those descriptors is always well-defined, we should rather use
the known sizes instead of trusting device-provided values to be
correct. Also adds some safety to potential out-of-order descriptors.
Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090
Signed-off-by: Julius Werner <jwerner@chromium.org>
Add a __weak function that can be overridden to reset devices
attached to an ehci devices after the FEAT_POWER has been submitted
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Set the usbethaddr based on the OMAP DIE_ID registers
which should be unique for each processor.
Then set this as the usb ethernet MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch fix wrong value returned by 's5p_gpio_part_max' function
for Exynos4412.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Without this patch, when the currently chosen environment to be written
has bad blocks, saveenv fails completely. Instead, when there is
redundant environment fall back to the other copy. Environment reading
needs no adjustment, as the fallback logic for incomplete writes applies
to this case as well.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
When executing nand scrub, the user gets the prompt:
Really scrub this NAND flash? <y/N>
We do not want the annoying usage displayed when saying N here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If a non-zero value is given to only_oob argument,
printing the main area is skipped.
With a little modification, we can skip the whole
while loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
add gpio common API support for gpio command
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[fix unnecessary cast]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix code to use pointer for pio port as the warning message suggested
remove the warning message
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix typo error for CONFIG_ENV_IS_NOWHERE from CONIG_ENV_IS_NOWHERE
Signed-off-by: Bo Shen <voice.shen@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The CONFIG_MAX_NAND_CHIPS never used, remove it
No where define LCD_TEST_PATTERN, so no need undefine
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
the smc cs related registers start at 0x600 and loop with 5 registers
so the reserved register should be in at91_smc structure while no in
at91_cs structure. So fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In this way, the pmecc corraction capbility can change in run time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Our Linux kernel switches the HDMI connector onto IPU0/DI1,
but the U-Boot display driver only supports IPU0/DI0 for the
time being.
Because of this, a soft re-boot will leave the HDMI output
connected to the wrong display port and prevent video from
being displayed.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Jim Lin
Fabio Estevam
Lukasz Majewski
Heiko Schocher
Julius Werner
Dan Murphy
Amaury Pouly
Piotr Wilczek
Phil Sutter
Masahiro Yamada
Jens Scharsig (BuS Elektronik)
Bo Shen
Bo Shen
Wu, Josh
Tom Rini
Eric Nelson
Andreas Wass
York Sun
Николай Пузанов
Shengzhou Liu
Shaohui Xie
Shruti Kanetkar