Commit 5ab502cb gathered all device tree sources
to arch/$(ARCH)/dts/.
So tegra124-venice2.dts also must go to arch/arm/dts directory
to build venice2 board.
(Commit 5ab502cb had been posted before venice2 board support
was merged. So an unvisible conflict happened.)
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.
It's always good to have a driver platform-independent.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
In Kbuild, every makefile must have non-empty obj- or obj-y.
Otherwise, built-in.o will not be created and the link stage
will fail.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If the whole code is surrounded by #ifdef(CONFIG_ ) .. #endif,
it should be moved to Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It is convenient to have all device trees on the same SoC compiled.
It allows for later easy repackaging without the need to re-run
the make file.
- Build device trees with the same SoC under arch/$(ARCH)/dts
- Copy the one specified by CONFIG_DEFAULT_DEVICE_TREE or
DEVICE_TREE=... to dts/dt.dtb
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.
I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.
For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.
This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Useful rules in scripts/Makefile.lib allows us to easily
generate a device tree blob and wrap it in assembly code.
We do not need to parse a linker script to get output format and arch.
This commit deletes ./u-boot.dtb since it is a copy of dts/dt.dtb.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
We are going to switch over to Kbuild in upcoming commits.
Each makefile must have non-empty obj- or obj-y
to generate built-in.o on Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Add the SATA boot support for OMAP5 and dra7xx.
Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.
Added the ROM boot device ID for SATA.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Typecast the argument with unsigned long long
for proper calculation of lldiv
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes
in the section 4.1.1 how this value calculation should be done.
This patch fixes the problem if network activity such as ping or
tftp is attempted after u-boot has been idle for an hour,
it hangs, and cannot control-C out of it.
Signed-off-by: Uday Hegde <udayh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch is here because of:
"arm: keep all sections in ELF file"
(sha1: 47ed5dd031)
Our tools expect to have elf with only LOAD header.
Without this fix also PHDR, INTERP and DYNAMIC headers
are available in ELF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The entries in config.mk were needed so that U-Boot could be built
with an old version of the Raspberry Pi Foundation's toolchain. Without
them, the build would error out with:
...-ld: error: .../libgcc.a(_bswapsi2.o) uses VFP register arguments,
u-boot does not
However, none of the 3 toolchains in the latest version of their
tools.git, nor the Ubuntu/Linaro ARM compilers in at least Ubuntu Quantal
or Saucy, need these options set in order to compile a working U-Boot.
Hence, remove the options for simplicity.
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
imx_get_fecclk() returns enet_ref instead of ipg.
Since the clock is used to calculate the prescaler
for the MDIO interface wrong values can be calculated.
Tested on a custom MX6S board with 100MBit interface
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.
Report it as MX6D instead:
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2),
it will cause warm reset fail, need to clear this MMDC_CHx_MASK field
to make sure all the i.MX6 series SOCs reset function work. Otherwise,
uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.
Signed-off-by: Anson Huang <b20788@freescale.com>
For low freq boot mode(ARM boot up with 396MHz), ROM
will not set AHB clock to 132MHz, and the reset value of
AHB divider is incorrect which will lead to wrong AHB
rate, need to correct it. To enable low freq boot mode,
need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL
SabreSD board and i.MX6SL EVK board.
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Use setbits/clrbits macro instead of readl/writel function.
(Suggested by Wolfgang)
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixed that cfg value is set to wrong value.
Because it didn't read the related register.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions. Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch adds s5p_cpu_rev.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to read cpu revision on Exynos CPU.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
Because of the list of peripherals is not sequential,
such a routine does not check for valid correctly.
Error check will be done when call the exynos_pinmux_config function.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
These are fairly complete, and near-clones of Tegra114 Venice, with an
additional I2C port, and MMC address changes for Tegra124.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These files are used by both SPL and main U-Boot.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These files are for code that runs on the CPU (A15) on Tegra124 boards.
At this time, there is no A15-specific code here. The warmboot/LP0 files
aren't included as that code hasn't been ported yet.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Masahiro Yamada
Alexey Brodkin
Dan Murphy
Andy Ng
Siva Durga Prasad Paladugu
Michal Simek
Soren Brinkmann
Sourav Poddar
Markus Niebel
Markus Niebel
Stephen Warren
Fabio Estevam
Anson Huang
Inha Song
Tom Rini
Rajeshwari S Shinde
Piotr Wilczek
Marek Vasut
Minkyu Kang
Tom Warren