The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
The configuration file has already enabled USB, but it
missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
on MPC8641HPCN can not work because of the wrong USB
register endian.
And add the USB command to U-Boot commands list.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
To get the IDS8247 board working following are done:
- FCC2 is deactivated
- FCC1 is activated
- I2C is activated
- CFI driver is activated
- Adapted for use with LIBFDT
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
Wolfgang is right: It's not a good idea to set up default initial
ethernet addresses for a board, even though they belong to the local
range.
This will change the failure mode from "IT manager screams at you for
using duplicate ethernet addresses" to a nice error message explaining
that the ethernet address hasn't been set properly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
The pxa255_idp being an old unmaintained board showed several issues:
1. CONFIG_INIT_CRITICAL was still defined.
2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined.
3. Symbol flash_addr was undeclared.
4. The boards lowlevel_init function was still called memsetup.
5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000.
6. Using -march=armv5 instead of -march=armv5te resulted in lots of
'target CPU does not support interworking' warnings on recent compilers.
7. The PXA's serial driver redefined FFUART, BTUART and STUART used as
indexes rather than the register definitions from the pxa-regs header
file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to
avoid any ambiguities.
8. There were several redefinition warnings concerning ICMR, OSMR3,
OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file.
9. The board configuration file was rather outdated.
10. The part header file defined the vendor, product and revision arrays
as unsigned chars instead of just chars in the block_dev_desc_t
structure.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
New board has faster oscillator and a different Flash chip. This affects:
- CFG_MPC5XXX_CLKIN
- SDRAM timings
- Flash CS configuration (timings)
- Flash sector size, and thus MTD partition layout
- malloc() arena size (due to bigger Flash sectors)
- smaller memory test range (due to bigger malloc() arena)
This patch also enables more extensive memory testing via "mtest".
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
PHYSADDR is for physical address, KSEG1ADDR is for uncached.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
On the MPC85xx CDS we have two issues:
1. The device tree fixup code did not check to see if the property we are
trying to update is actually found. Its possible that it would update
random memory starting at 0.
2. Newer Linux kernel's have moved the location of the PCI nodes to be
sibilings of the soc node and not children. The explicit PATH to the PCI
node would not be found for these device trees. Add the ability to handle
both paths. In the future we shouldn't handle such fixups by explicit path.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured
console. Make it so we match that config what we tell Linux as the early
STDOUT console.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
CFG_MEMTEST_START uses weird magic involving gd, which fails to
compile. Use hardcoded values instead (we actually know how much RAM
we have on board.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
/bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded
nulls in a string differently. For example, the following statement:
echo "this is a string\0" > afile
Will produce the following with /bin/bash:
"this is a string\0"
But with /bin/dash, will produce:
"this is a string
Bug fixed by moving the embedded null out of the makefile and into the
config header. Also renamed the macro to avoid usage colision with the same
macro used by other board ports.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Updates to atstk1002 U-Boot header file:
- Changed bootargs:
* Set the bootargs for at1002 to point to the SD-card partition instead
* ... of the boot flash.
* Removing the rootfstype since that argument are not needed.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch applies some clarifying comments to how the different
clocks are setup according to atstk1002.h Some of the previous
comments where stating wrongful information.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
With recent toolchains, the environment sectors were no longer aligned to
sector boundaries. The reason was a combination of two bugs:
1) common/environment.c assumed that CONFIG_TQM8xxL would be defined
for all TQM8xxL and TQM8xxM boards. But "include/common.h", where
this gets defined, is not included here (and cannot be included
without causing lots of problems).
Added a new #define CFG_USE_PPCENV for all boards which really
want to put the environment is a ".ppcenv" section.
2) The linker scripts just include environment.o, silently assuming
that the objects in that file are really in the order in which
they are coded in the C file, i. e. "environment" first, then
"redundand_environment", and "env_size" last. However, current
toolchains (GCC-4.x) reorder the objects, causing the environment
data not to start on a flash sector boundary:
Instead of: we got:
40008000 T environment 40008000 T env_size
4000c000 T redundand_environment 40008004 T redundand_environment
40010000 T env_size 4000c004 T environment
Note: this patch fixes just the first part, and cures the alignment
problem by making sure that "env_size" gets placed correctly. However,
we still have a potential issue because primary and redundant
environment sectors are actually swapped, i. e. we have now:
40008000 T redundand_environment
4000c000 T environment
40010000 T env_size
This shall be fixed in the next version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jason Jin
Wolfgang Denk
Zhang Wei
Jean-Christophe PLAGNIOL-VILLARD
Sergej Stepanov
Haavard Skinnemoen
TsiChungLiew
Bartlomiej Sieka
Martin Krause
Marcel Ziswiler
Rune Torgersen
Vlad Lungu
Kumar Gala
Jon Loeliger
Stefan Roese
Michal Simek
Grzegorz Bernacki
Marian Balakowicz
Grant Likely
Peter Pearse
Eirik Aanonsen
Kyungmin Park