We want the SPI flash probing feature to operate as a standard driver.
Add a driver for the basic probing feature used by most boards. This
will be activated by device_probe() as with any other driver.
The 'sf probe' command currently keeps track of the SPI slave that it
last used. This doesn't work with driver model, since some other driver
or system may have probed the device and have access to it too. On the
other hand, if we try to probe a device twice the second probe is a nop
with driver model.
Fix this by searching for the matching device, removing it, and then
probing it again. This should work as expected regardless of other device
activity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust spi_flash_probe_slave() to return an error value instead of a
pointer so we get the correct error return.
Have the caller allocate memory for spi_flash to simplify error handling,
and also so that driver model can use its existing allocated memory.
Add a spi.h include in the sf_params file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
enable the W#/Vpp signal to disable writing to the status
register on ST MICRON flashes like the N25Q128 thorugh
the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Currently, flash quad bit is set in "spi_flash_validate_params" and later
at the end in the same api, we write 0 to status register for few flashes,
thereby overriding the quad bit set. This fix moves the quad bit setting
outside this api in "spi_flash_probe_slave"
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The commit 6af8dc3ebc broke support for
S25FL032P and S25FL064P by carelessly removing the code handling special
page size for these two SPI NOR flashes and unifying the code under the
assumption that Extended JEDEC ID of 0x4d00 always implies 512b page size.
Add special case handling for these two SPI NOR flashes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Squash the malloc()+memset() combo in favor of calloc().
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch added support for accessing dual memories in
parallel connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch added support for accessing dual memories in
stacked connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
QEB code comprises of couple of flash register read/write operations,
this patch moved flash register operations on to sf_op
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch adds set QEB support for macronix flash devices
which are trying to program/read quad operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Moved the flash params table from sf_probe.c and
placed on to sf_params.c, hence flash params file will
alter based on new addons.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch enabled RD_FULL and WR_QPP for supported flashes
in micron, winbond and spansion.
Remaining parts will be add in future patches.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch provides support to set the quad enable bit on flash.
quad enable bit needs to set before performing any quad IO
operations on respective SPI flashes.
Currently added set quad enable bit for winbond and spansion flash
devices. stmicro flash doesn't require to set as qeb is volatile.
remaining flash devices support will add in future patches.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch add quad commands support like
- QUAD_PAGE_PROGRAM => for write program
- QUAD_OUTPUT_FAST ->> for read program
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Current sf uses FAST_READ command, this patch adds support to
use the different/extended read command.
This implementation will determine the fastest command by taking
the supported commands from the flash and the controller, controller
is always been a priority.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support for Macronix MX25L2006E SPI flash.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
All other hex values in sf_probe.c are in lower case so we should
fix this one too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write. Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.
sjg@chromium.org added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the spi flash transfer to multiple parts, it is forgot to add
Atmel AT25DF321 spi flash support, which broken several Atmel EK
boards which this chip. So, add it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Qspi controller can have a memory mapped port which can be used for
data read. Added support to enable memory mapped port read.
This patch enables the following:
- It enables exchange of memory map address between mtd and qspi
through the introduction of "memory_map" flag.
- Add support to communicate to the driver that memory mapped
transfer is to be started through introduction of new flags like
"SPI_XFER_MEM_MAP" and "SPI_XFER_MEM_MAP_END".
This will enable the spi controller to do memory mapped configurations
if required.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Use flash->page_size arg in print_size() instead of
flash->sector_size while printing detected flas part details.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Compared to other spi flashes, ramtron has a different
probing and implementation on flash ops, hence moved
ramtron probe code into ramtron driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
From Micron, 512MB onwards, flash requires to poll flag status
instead of read status- hence added E_FSR flag on spectific
flash parts.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
SECT_4K, SECT_32K and SECT_64K opeartions are performed to
to specific flash by adding a SECT* flag on respective
spi_flash_params.flag param.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Few of the flashes(Atmel, Macronix and SST) require to
clear BP# bits in flash power ups.
So clear these BP# bits at probe time, so-that the flash
is ready for user operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Most of the SST flashes needs to write up using SST_WP, AAI
Word Program, so added a flag param on spi_flash_params table.
SST flashes, which supports SST_WP need to use a WP write
sst_write_wp instead of common flash write.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added AT45DB* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added SST25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Added S25FL* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added W25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added MX25L* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Simon Glass
Heiko Schocher
Poddar, Sourav
Marek Vasut
Jagannadha Sutradharudu Teki
Luka Perkov
Mike Frysinger
Bo Shen
Priyanka Jain