The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not
ALT1 (which even corresponds to nothing).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX35. The content of the file is taken from Linux kernel at commit
267dd34, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX25. The content of the file is taken from Linux kernel at commit
267dd34, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Augment the MX5 clock code with function to enable and configure
NFC clock. This is necessary to get NFC working on MX5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Fix minor adjustments needed to get SPL framework building on MX5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
The U-Boot SPL can parse the uImage format and gather information from
it about the payload. Make use of this and wrap u-boot.bin into uImage
format. The benefit is the SPL will know the size of the payload
instead of using fixed size of the payload defined at compile time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Add support for generic NAND SPL via the SPL framework into the
mxc_nand_spl driver. This is basically just a simple rename and
publication of the already implemented functions. To avoid the
bare-bones functions getting in the way of the NAND_SPL, build
them only if CONFIG_SPL_FRAMEWORK is not defined.
Also make sure the requested payload is aligned to full pages,
otherwise this simple driver fails to load the last page.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The MX53 ROM loads the data from NAND in multiples of pages and
supports maximum page size of 4k. Thus, align the image and header
to 4k to be safe from ROM bugs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL
as 0x2, which means:
PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per
FSL bootlets code.
mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved".
HW_DRAM_CTL8 is setup as the last element.
So skip the initialization of these DRAM_CTL registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18.
Remove this erroneous setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx23 the pad voltage selection bit needs to be always '0', since '1' is a
reserved value.
For example:
Pin 108, EMI_A06 pin voltage selection:
0= 1.8V (mDDR) or 2.5V (DDR1);
1= reserved.
Fix the pad voltage definitions for the mx23 case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.
Signed-off-by: Tom Rini <trini@ti.com>
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.
Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.
The changes are not very large, but it is good to document them so that user
can get it working at once.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add the tlb entries based on the configuration of the SRIO interfaces.
Every SRIO interface has 256M space:
#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For T4/B4, the clockgen node compatible string is updated to version 2.
Add clock-frequency setting for this new version.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420/B4860 PCIE can not work because of the wrong definition of
the PCIE register offset in the file:
arch/powerpc/include/asm/immap_85xx.h
Add the judgement of B4420/B4860 to make the register offset to:
#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Set the device tree property associated with the mpic source
frequency. The frequency is used for mpic timer.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.
Also removed unnecessary static global variables.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For linux 3.x, the size of each item in interrupt-map property is 9 not 7.
Don't use the static value and calculate the size with following cells:
PCI #address-cells, PCI #interrupt-cells,
PIC address, PIC #address-cells, PIC #interrupt-cells.
Signed-off-by: Bin Jiang <bin.jiang@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
Signed-off-by: Stefan Roese <sr@denx.de>
The v2013.04 release has this patch set included:
5cb48582 "Add architecture-specific global data"
With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.
This patch now uses the automatically generated struct size instead to
not run into this problem again.
Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!
Signed-off-by: Stefan Roese <sr@denx.de>
Benoît Thébaudeau
Marek Vasut
Fabio Estevam
Tom Rini
Shaohui Xie
Xu Jiucheng
Cristian Sovaiala
York Sun
Shengzhou Liu
Timur Tabi
Zhicheng Fan
Poonam Aggrwal
Prabhakar Kushwaha
Horst Kronstorfer
Xulei
Liu Gang
Zang Roy-R61911
Tang Yuantian
Matthew McClintock
Dongsheng.wang@freescale.com
Jeffrey Ladouceur
Jiang Bin
Stefan Roese
Anatolij Gustschin