The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c2
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.
Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.
This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be
using imply instead in arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
The check for OMAP3630/3730 only checks for 800MHz 3630/3730, but
anything else is lumped into 36XX/37XX with an assumed 1GHz speed.
Based on the DM3730 TRM bit 9 shows the MPU Frequency (800MHz/1GHZ).
This also adds the ability to distinguish between the DM3730, DM3725,
AM3715, and AM3703 and correctly display their maximum speed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
Currently all backend driver ops uses hard coded physical
address, so to adopt the driver to DM, add device pointer to ops
call backs so that drivers can get physical addresses from the
usb driver priv/plat data.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini
Adam Ford
Simon Glass
Siarhei Siamashka
Ladislav Michl
Mugunthan V N