When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.
Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.
Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable device tree control in
u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
These files are taken verbatim from the Linux kernel 4.17
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The SION pin must be set for proper operation of I2C when DM is enabled.
When legacy I2C is used, this bit is set implicitly in the u-boot code:
arch/arm/include/asm/arch-mx5/iomux-mx53.h:92:
MX53_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x368, 0x040, 4 |
IOMUX_CONFIG_SION, 0x820, 0, NO_PAD_CTRL),
The Linux kernel uses similar approach with:
arch/arm/boot/dts/imx53-tqma53.dtsi:182:
MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000
After applying this patch it is possible to have the I2C working with DM
on imx53 devices:
MX53_PAD_KEY_ROW3__I2C2_SDA (0x1ee | IMX_PAD_SION)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
CONFIG_ENV_IS_IN_MMC must be declared in defconfig to properly
support "env save".
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The mx6_common.h file already defines BOUNCE_BUFFER so no need to
definit it again in specific configs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It makes sense to select the MP multi processor option at the same time we
select the other SMP options needed for SMP capable i.MX6 SoCs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Also remove the #ifdef's from clock.h since the Kconfig values defaults
the to old default values in clock.h.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Configure video arguments at run-time instead of at compile-time.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
B{46}50v3s have an internal LCD that needs to be configured,
in comparison with B850v3 which has only external displays.
Use VPD instead of `CONFIG_TARGET_GE_B{4,6,8}50V3' compile-time
checks to correct initialize video based on the monitor type.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Move the VPD reading earlier in order to establish the monitor
type as soon as possible.
The configuration of the specific environment variables needs to be
done later after the environment is configured.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable Video PLL to fix non-working display support for Bx50v3
internal displays.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify process_vpd() by unifying the switch statements handling
product specific configurations.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The detect_baseboard() function actually determines whether there is an
internal LCD panel or not. Rename for clarity.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add winbond SPI NOR support, which is being used by newer hardware.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This was unintentionally disabled when moving MVGBE to Kconfig.
Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Not all the udevice have a available DT node, eg. rksdmmc@ff500000.blk
which add by mmc_bind(), these device do not have/need set pinctrl
state.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the U-Boot base directory happens to have the same name as the branch
that buildman is directed to use via the '-b' option and no output
directory is specified with '-o', buildman happily starts removing the
whole U-Boot sources eventually only stopped with the error message:
OSError: [Errno 20] Not a directory: '../<branch-name>/boards.cfg
Add a check to avoid this and also deal with the case where '-o' points
to the source directory, or any subdirectory of it.
Finally, tidy up the confusing logic for removing the old tree when using
-b. This is only done when building a branch.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
To address that situation we discussed on the list moving to
genetic_set_bit() instead.
Doing a quick grep for similar situations in drivers/usb shows that the
composite device is using __set_bit().
This patch switches over to generic_set_bit to maintain consistency between
the two gadget drivers.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
Looking at the provenance of the current u-boot code and the git change
history in the kernel, it looks like we have a local copy of set_bit and
clear_bit as a hold-over from porting the Linux driver into u-boot.
These days __set_bit and __clear_bit are optionally provided by an arch and
can be used as inputs to generic_bit_set and generic_bit_clear.
This patch switches over to generic_set_bit and generic_clear_bit to
accommodate.
Tested on i.MX WaRP7 and Intel Edison
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
nds2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nds32 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
nds32 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nds32
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
nios2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nios2 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
nios2 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nios2
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
riscv bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
riscv bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
riscv bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
x86 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
mv_ddr_build_message.c is generated in Marvell's standalone mv_ddr code.
When imported into u-boot we need to add the appropriate SPDX tag and
re-format it slightly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This commit adds basic support for PWM found on Allwinner A64.
It can be used for pwm_backlight driver (e.g. for Pinebook)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Currently dw_hdmi configures HSYNC polarity using VSYNC setting from
EDID and vice versa. Fix it, since it breaks displays where HSYNC
and VSYNC polarity differs
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The check is necessary to avoid NULL pointer dereference.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Chris Packham
Lukasz Majewski
Sebastian Reichel
Peter Robinson
Magnus Lilja
Ian Ray
Nandor Han
Tom Rini
Kever Yang
Lothar Waßmann
Bryan O'Donoghue
Vasily Khoruzhick
Ramon Fried