The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Thus far, the socfpga init code had hard-coded the configuration
of the ethernet PHY interface to RGMII in the ethernet registers
in sysmgr space, so PHYs connected in another modes did not work.
This patch fixes support for configurations where the ethernet PHYs
are connected over MII/GMII/RMII interfaces by parsing the phy-mode
OF property of the GMACs and configuring the ethernet registers in
sysmgr space accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
ARM defines __raw_writes[bwql], __raw_reads[bwql] in arch io.h
but not the writes[bwql], reads[bwql] needed by some drivers.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch aims to fix the order of CSU slave index for the LS1021a
board.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When switching between the early and final mmu tables, the stack will
get corrupted if the Non-Secure attribute is different. For ls1043a,
this issue is currently masked because flush_dcache_all is called
before the switch when CONFIG_SYS_DPAA_FMAN is defined.
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.
The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This option enable adding new platform suport just by adding defconfig
and DTS file which will target generic configuration for SoC.
Make no sense to extend Kconfig just create a pointer between DTS and
configuration file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Armada 375 still has some problems with d-cache enabled in the ethernet
driver (mvpp2). So lets keep the d-cache disabled until this is solved.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the Armada 375. Please note that
currently the SerDes and DDR3 init code for the A375 is not
included / enabled. This will be done in a later, follow-up patch.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
First supported chip is APQ8016 (that is compatible with MSM8916).
Drivers in SoC code:
- Reset controller (PSHOLD)
- Clock controller (very simple clock configuration for MMC and UART)
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The default board_init_f() implementation performs a call to
board_init_r() as the last step of the sequence. Fix the comment
for this function to reflect the actual execution flow.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds an explanation of which Raspberry Pi models each target option
supports.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
MSMC segment Privilege ID is not consistent accross the keystone2 SoCs.
As the first step to ensure complete SoC wide coherency setup, lets
refactor the macros to remove the #if-deffery around the code which
obfuscates which IDs are actually enabled for which SoC.
As a result of this change the PCIe configuration is moved after the
msmc configuration is complete, but that should ideally have no
functional impact.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Move most of the flags required into LLVM_RELFLAGS to test at build
time instead of requiring them to be passed in.
- Update doc/README.clang to reflect this
- Switch to rpi_2 as the example as it's closer to working out of the
box than rpi is.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.
This patch adds a defconfig and device tree chunks for it.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We currently depend SPL config options on specific machine types which doesn't
scale. Fortunately there's already a kconfig variable that tells us whether we
want to build SPL code at all, so just depend them on this.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.
Move all files that are not really tied to armv7 into a new mach-sunxi
directory.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the H8Homlet v2 dts to enable USB
in U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the Cubietruck Plus dts to enable USB
in U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This provides the minimal changes to the A83T dtsi to enable USB in
U-boot. It is not what will be submitted to the kernel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Eliminate the "ph1"_ prefixes from function names because "uniphier_"
describes the SoC familiy better.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On PH1-sLD3, eMMC and NAND are assigned to different I/O pins.
Both devices can be enabled at the same time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, these functions assume #address-cells and #size-cells are
both one. Fix them to support 64bit DTB.
Also, I am fixing a buffer overrun bug while I am here. The array
size of gd->bd->bd_dram is CONFIG_NR_DRAM_BANKS. The number of
iteration in the loop should be limited by that CONFIG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since no clock driver is implemented for peripherals in U-Boot yet,
this property is needed for the serial driver to set up the divisor
register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The A83T has 3 PHYs, the last one being HSIC, which has 2 clocks.
Also there is only 1 OHCI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This bit needs to be set for system suspend/resume to work. This setting
will be documented in an updated TRM at some time in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs
to be put in bypass mode in uboot to enable CAAM transcations to pass
through.
For non-secure boot, SP BootROM doesn't enable SMMU, which is in
bypass mode out of reset.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The GUR (DCFG) registers in CCSR space are in little endian format.
Define a config CONFIG_SYS_FSL_CCSR_GUR_LE in
arch/arm/include/asm/arch-fsl-layerscape/config.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
"fdt_high" env variable was set to 0xcfffffff for secure boot.
Change it to 0xa0000000 for LS2080 to be consistent with non-secure
boot targets.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To unify steps for secure boot for xip (eg. NOR) and non-xip memories
(eg. NAND, SD), bootscipts and its header are copied to main memory.
Validation and execution are performed from there.
For other ARM Platforms (ls1043 and ls1020), to avoid disruption of
existing users, this copy step is not used for NOR boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Marek Vasut
Purna Chandra Mandal
York Sun
Vincent Siles
Ed Swarthout
Stefan Roese
Michal Simek
Joe Hershberger
Mateusz Kulikowski
Paul Kocialkowski
Andreas Dannenberg
Stephen Warren
Nishanth Menon
Tom Rini
Siarhei Siamashka
Alexander Graf
Chen-Yu Tsai
Masahiro Yamada
Hans de Goede
Stephen Warren
Rai Harninder
Qianyu Gong
Mingkai Hu
Saksham Jain