If U-Boot is chain-loaded from a previous boot loader we must set up the
clocks the way U-Boot wants them. Add code for this. It will do nothing if
SPL has already done the job.
Signed-off-by: Simon Glass <sjg@chromium.org>
Detect with a previous boot loader has already set up the clocks and set
them up again so that U-Boot gets what it expects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Shifted masks are the standard approach with rockchip since it allows
use of the mask without shifting it each time. Update the definitions and
the driver to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
On reset the standby bit is clear, but if U-Boot is chain-loaded from
another boot loader it may be set. Clear it before starting up video so
that it works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add remove() methods for EDP and VOP so that U-Boot can shut down the
video on exit. This avoids leaving DMA running while booting Linux which
can cause problems if Linux uses the frame buffer for something else.
It also makes it clear what is needed to shut down video.
While we are here, make rkvop_enable() static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Most Chromebooks support chain-loading U-Boot but instructions are
somewhat scattered. Add a README to hold this information within the
U-Boot tree. Also add the standard developer keys to simplify the
instructions, since they are small.
For now this only supports nyan-big.
Signed-off-by: Simon Glass <sjg@chromium.org>
The clock fix-up for tegra is still present in the code. It causes a
divide-by-zero bug after relocation when chain-loading U-Boot from
coreboot. Fix this by adding a check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7468676 (ARM: tegra: fix clock_get_periph_rate() for UART clocks)
At present CP15 init is disabled on tegra. Use the correct option so that
this init is performed on boot. This enables the instruction cache, for
example, which is critical to the machine running at full speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot is the secondary boot loader, or has been run from itself, the
SOR may already be powered up. Powering it up again causes a hang, so
detect this situation and skip it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Enable this so we can roughly measure CPU performance. Also enable the
cache command to allow for timing.
Signed-off-by: Simon Glass <sjg@chromium.org>
For devices that need a delay between SPI transactions we seem to need an
additional delay before the first one if the CPU is running at full speed.
Add this, under control of the existing setting. At present it will only
be enabled with the Chrome OS EC.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the interrupt does not work and the SPI bus runs much less
quickly than it should. Add settings to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present early clock init happens in SPL. If SPL did not run (because
for example U-Boot is chain-loaded from another boot loader) then the
clocks are not set as U-Boot expects.
Add a function to detect this and call the early clock init in U-Boot
proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file does not report a few possible errors and one message is missing
a newline. Fix these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If CONFIG_ARMV7_LPAE is not defined we should make sure that the feature
is disabled. This can happen if U-Boot is chain-loaded from another boot
loader which does enable LPAE.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_ARMV7_LPAE is defined then mmu_setup() will use
instructions which are invalid on ARMv4T. This happens on Tegra since it
has an ARMv4T boot CPU. Add a check for the architecture version to allow
the code to be built. It will not actually be executed by the boot CPU,
but needs to compile.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option allows skipping the call to lowlevel() while still performing
CP15 init. Support this on ARM720T so it can be used with Tegra.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename command ls to fsls as its conflicting with
generic file systesm command ls and this is causing
compilation failure as below, if both are enabled
and this patch fixes it.
cmd/jffs2.o:(.u_boot_list_2_cmd_2_ls+0x0):
multiple definition of `_u_boot_list_2_cmd_2_ls'
cmd/fs.o:(.u_boot_list_2_cmd_2_ls+0x0):first defined here
scripts/Makefile.build:359: recipe for target 'cmd/built-in.o'
failed
make[1]: *** [cmd/built-in.o] Error 1
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is some inconsistency between uses of CONFIG_RTC_DS13xx and
CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from
these variables.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
With overrun enabled, serial port console freezes & stops receiving data with
overun error if we keep sending data.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Enable support for XIP (execute in place) of U-Boot or kernel image. There is
no need to copy image from flash to ram if flash supports execute in place.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Documents the externally visible functions shared between the VOP
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documents the externally visible functions shared between the HDMI
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the warning,
---8<---
CACHE: Misaligned operation at range [3fdffff0, 3fdffffc]
---<8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds TVE base address for Allwinner H3 and H5 SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to avoid future confusion with similary named files, rename
tve.c to tve_common.c. New name better represents the fact that this file
holds code which can be and will be shared between multiple drivers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit fixes the warning produced by gcc 7.1.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The addresses of the registers in TI TPS65217 are not continuous.
There is a gap between ENABLE(0x16) and DEFUVLO(0x18). No 0x17
register available.
Fixup the enum values by adding a 'reserved' placeholder to correct
the addresses higher than 0x17.
Series-to: Heiko Schocher <hs@denx.de>
Signed-off-by: Brock Zheng Techyauld Ltd <yzheng@techyauld.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The driver provides regulator set/get voltage
enable/disable functions for lp87565 family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support to bind the regulators/child nodes with the pmic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
We do not need to probe the block device here, so avoid doing so. The MMC
device itself must be active, but the block device can come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make sure that we probe the block device before using it when reading
the environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Many devices support a child block device (e.g. MMC, USB). Add a
convenient way to get this device given the parent device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Some boards like am437x-gp-evm require dcdc3 also to be configured
as it feeds on to ddr. Hence add the capability as well.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass
Sekhar Nori
Siva Durga Prasad Paladugu
Chris Packham
Vikas Manocha
Philipp Tomsich
Wenyou Yang
Jernej Skrabec
Brock Zheng Techyauld Ltd
Keerthy
Marek Vasut
Kouei Abe