Clean a mixup between u32 and int as a return type
for functions returning error values.
Use int as it is native (and widely used) return type.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
There is no benefit in using u8, so switch to unsigned to reduce the
binary image size (by 20 bytes).
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
Add partial ULPI specification implementation that should be enough to
interface the ULPI PHYs in the boot loader context.
Add a viewport implementation for Chipidea/ARC based controllers.
Signed-off-by: Jana Rapava <fermata7@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Simon Glass <sjg@chromium.org>
This patch allows USB to work on some hosts, which need additional frobing after
the host was powered up via regular USB powerup sequence.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
This is useful for USB Transceivers init etc.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Remy Bohmer <linux@bohmer.net>
This commit provides UDC driver support for Samsung's SoC
family of processors.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
On some usb device controllers (pxa) the endpoint configuration must be programmed prior to enable it.
Signed-off-by: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Remy Bohmer <linux@bohmer.net>
Fix:
at91_emac.c: In function 'at91emac_phy_init':
at91_emac.c:244:20: warning: variable 'duplex' set but not used
[-Wunused-but-set-variable]
at91_emac.c:244:13: warning: variable 'speed' set but not used
[-Wunused-but-set-variable]
Use new debug_cond() to fix these warnings. In the result, anumber of
inconsistent printf() formats are detected:
at91_emac.c: In function 'at91emac_read':
at91_emac.c:147:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c: In function 'at91emac_write':
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 2 has type 'struct at91_emac_t *'
[-Wformat]
at91_emac.c:157:2: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'short unsigned int *'
[-Wformat]
at91_emac.c: In function 'at91emac_recv':
at91_emac.c:451:3: warning: format '%d' expects argument of type
'int', but argument 2 has type 'long unsigned int' [-Wformat]
at91_emac.c:451:3: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat]
Fix these, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jens Scharsig <js_at_ng@scharsoft.de>
Cc: Andreas Bießmann <andreas.devel@gmail.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
Fix:
ne2000_base.c: In function 'dp83902a_send':
ne2000_base.c:282:7: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_RxEvent':
ne2000_base.c:376:5: warning: variable 'rsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_TxEvent':
ne2000_base.c:513:5: warning: variable 'tsr' set but not used
[-Wunused-but-set-variable]
ne2000_base.c: In function 'dp83902a_ClearCounters':
ne2000_base.c:550:17: warning: variable 'cnt3' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:11: warning: variable 'cnt2' set but not used
[-Wunused-but-set-variable]
ne2000_base.c:550:5: warning: variable 'cnt1' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
This was used by the AVP in early boot but is no longer used. Unless we
plan to enable it somehow it is not needed. In any case we should try
to use the ns16550 driver instead as it has the same code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... rather than open-coding the register accesses.
However, gpio_request() typically stores the "label" parameter in a global
data structure. This causes problems when called from gpio_config_uart(),
since the code is running before relocation. To solve this, pass a NULL
string to gpio_request(), and modify gpio_request() not to touch the string
if it's NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
MMC interfaces are specified to be 3.3V compatible with an operating
voltage range of 3.1V to 3.5V for SD cards. This change affects
hardware using TWL4030 (TPS6595x) PMICs and should improve the
reliability when communicating with marginally-spec'd MMC devices.
3.15V is the highest possible level for this chip. This patch
has been tested on a Gumstix Overo board.
Signed-off-by: Ash Charles <ash@gumstix.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Fix:
da8xx_gpio.c: In function 'gpio_toggle_value':
da8xx_gpio.c:208:23: warning: variable 'bank' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
ep0.c: In function 'ep0_get_descriptor':
ep0.c:187:8: warning: variable 'cp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Fix:
core.c: In function 'usbd_device_event_irq':
core.c:596:21: warning: variable 'state' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Fix:
musb_udc.c: In function 'musb_peri_softconnect':
musb_udc.c:166:14: warning: variable 'intrtx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:166:6: warning: variable 'intrrx' set but not used
[-Wunused-but-set-variable]
musb_udc.c:165:5: warning: variable 'intrusb' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Fix:
ehci-mxc.c: In function 'ehci_hcd_init':
ehci-mxc.c:113:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips
which currently fail to build due to dropped pre-CONFIG_NET_MULTI code.
This v2 patch minimizes the number of lines in the diff for easy review
and to eliminate any possible accidential changes resulting from moving
lines of code in the file. This also makes the register function very easy.
Any cleanups and improvements are intentionally deferred to follow-up patches
to keep this patch as simple and as easy to review as possible.
A new driver register function, ne2k_register() calls the existing
one-time setup part of the old init function and calls eth_register().
Changes to shmin, r7780mp and qemu-mips:
- Call the new ne2k_register() from board_eth_init() of the boards.
- Tested using qemu-mips board,
- Tested the two renesas / sh boards r7780mp and shmin to compile again,
and should work.
checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf,
and no warnings introduced in none of the three boards using this driver.
Signed-off-by: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Fix:
inca-ip_sw.c: In function 'inca_switch_init':
inca-ip_sw.c:210:6: warning: variable 'v' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
nand_spl_load.c: In function 'nand_boot':
nand_spl_load.c:31:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix warnings for both cases:
definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:156:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
not definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:196:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix:
cfb_console.c:371: warning: 'cursor_state' defined but not used
cfb_console.c:372: warning: 'old_col' defined but not used
cfb_console.c:373: warning: 'old_row' defined but not used
cfb_console.c:435: warning: 'video_invertchar' defined but not used
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Wolfgang Denk <wd@denx.de>
TPM (Trusted Platform Module) is an integrated circuit and
software platform that provides computer manufacturers with the
core components of a subsystem used to assure authenticity,
integrity and confidentiality.
This driver supports version 1.2 of the TCG (Trusted Computing
Group) specifications.
The TCG specification defines several so called localities in a
TPM chip, to be controlled by different software layers. When
used on a typical x86 platform during the firmware phase, only
locality 0 can be accessed by the CPU, so this driver even while
supporting the locality concept presumes that only locality zero
is used.
This implementation is loosely based on the article "Writing a
TPM Device Driver" published on http://ptgmedia.pearsoncmg.com
Compiling this driver with DEBUG defined will generate trace of
all accesses to TMP registers.
This driver has been tested and is being used in three different
functional ChromeOS machines (Pinetrail and Sandy Bridge Intel
chipsets) all using the same Infineon SLB 9635 TT 1.2 device.
A u-boot cli command allowing access to the TPM was also
implemented and is being submitted as a second patch.
Change-Id: I22a33c3e5b2e20eec9557a7621bd463b30389d73
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
CC: Wolfgang Denk <wd@denx.de>
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
This patch fixes a small off-by-one bug in the GPIO driver for the mxs platform that allowed the selection gpio pins of one bank more than the SoC actually has.
Signed-off-by: Robert Deliën <robert at delien.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Some functions were internal to the apbh dma driver, so annotate them static.
Some of the functions weren't used at all so drop them. This makes the U-Boot
binary smaller by about 1500 bytes.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
When a timeout occurs, the return value is prepared but never returned.
Fix that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fix the condition for number of phys in
davinci_eth_phy_detect() function.
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT indicates number of
phys. From this commit id dc02badab4
davinci emac initilazed one less than the number of phy count.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
move struct davinci_rtc to arch/arm/include/asm/arch-davinci/hardware.h
and add RTC_KICK0R_WE, RTC_KICK1R_WE defines,
so they are global useable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Use software ECC for the SPL build if support for software ECC in SPL is
enabled.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Scott Wood <scottwood@freescale.com>
This patch adds support for software ECC to the nand_spl_simple driver.
To enable this one have to define CONFIG_SPL_NAND_SOFTECC.
Tested on OMAP3.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Scott Wood <scottwood@freescale.com>
For some reason code setting the speed based on the PHY feedback causes
troubles on AM3517 so hardcode 100Mbps for now.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
DaVinci EMAC is present on TI AM35xx SoCs (ARMv7) which run with D-Cache
enabled by default. So we have to take care and flush/invalidate the
cache before/after the DMA operations.
Please note that the receive buffer alignment to 32 byte boundary comes
from the old driver version I don't know if it is really needed or
alignment to cache line size is enough.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
On AM35xx CPPI RAM had different addresses when accessed from the CPU
and from the EMAC. We need to account this to deal with the buffer
descriptors correctly.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h
DaVinci specific PHY drivers hacked to include the new header. We might
want to switch to phylib in future.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
s3c64xx.c implemented its own nand_read_byte, nand_write_buf and
nand_read_buf functions. This provoked a regression when these functions
were made public by patch 55f429bb39614a16b1bacc9a8bea9ac01a60bfc8.
This deletes these duplicated functions from s3c64xx.c and adds the generic
implementations in nand_base.c to the spl Makefile. It also adds
-ffcuntion-sections and -gc-sections to the compilation flags of the SPL to
avoid errors originating from unused functions in nand_base.c.
Description of the regression:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/108873
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Functions often used in SPL are now part of linux/mtd/nand.h.
Static modifiers are removed from these functions in
drivers/mtd/nand/nand_base.c.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Acked-by: Scott Wood <scottwood@freescale.com>
Igor Grinberg
Jana Rapava
Marek Vasut
Wolfgang Grandegger
Lukasz Majewski
Vincent Palatin
Stefan Herbrechtsmeier
Lei Wen
Wolfgang Denk
Jason Liu
Simon Glass
Stephen Warren
Ash Charles
Anatolij Gustschin
Bernhard Kaindl
Vadim Bendebury
Stefano Babic
Robert Deliën
Wolfram Sang
Prabhakar Lad
Heiko Schocher
Ilya Yanok
Simon Schwarz
Ajay Bhargav