Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Append "debug server FW" in error message to make more informative.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of VSC8584 phy placed on new QSGMII/SGMII ethernet riser cards
used on LS2085QDS platforms.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
RTC devices can generate 32KHz output if for
-DS3232 device, EN32KHz bit and BB32KHz bit are set
-DS3231 device, EN32KHz bit is set, BB32KHz bit is don't care
Patch adds rtc_enable_32khz_output() which when called
will enable 32KHz output on 32KHz pin
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This driver actually does nothing but test pinctrl uclass, and
demonstrate how things work.
To try this driver, uncomment /* #define DEBUG */ in the
drivers/pinctrl/pinctrl-sandbox.c, and debug messages will be
displayed.
DRAM: 128 MiB
sandbox pinmux: group = 1 (serial_a), function = 1 (serial)
Using default environment
In: cros-ec-keyb
Out: lcd
Err: lcd
Net: Net Initialization Skipped
eth0: eth@10002000, eth1: eth@80000000, eth5: eth@90000000
=> i2c dev 0
Setting bus to 0
sandbox pinmux: group = 0 (i2c), function = 0 (i2c)
sandbox pinconf: group = 0 (i2c), param = 3, arg = 1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This creates a new framework for handling of pin control devices,
i.e. devices that control different aspects of package pins.
This uclass handles pinmuxing and pin configuration; pinmuxing
controls switching among silicon blocks that share certain physical
pins, pin configuration handles electronic properties such as pin-
biasing, load capacitance etc.
This framework can support the same device tree bindings, but if you
do not need full interface support, you can disable some features to
reduce memory foot print. Typically around 1.5KB is necessary to
include full-featured uclass support on ARM board (CONFIG_PINCTRL +
CONFIG_PINCTRL_FULL + CONFIG_PINCTRL_GENERIC + CONFIG_PINCTRL_PINMUX),
for example.
We are often limited on code size for SPL. Besides, we still have
many boards that do not support device tree configuration. The full
pinctrl, which requires OF_CONTROL, does not make sense for those
boards. So, this framework also has a Do-It-Yourself (let's say
simple pinctrl) interface. With CONFIG_PINCTRL_FULL disabled, the
uclass itself provides no systematic mechanism for identifying the
peripheral device, applying pinctrl settings, etc. They must be
done in each low-level driver. In return, you can save much memory
footprint and it might be useful especially for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is useful when we want to bind a device, but do not need the
pointer to the device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert the tpm_tis_lpc driver to use driver model and update boards which
use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Convert the tpm_tis_i2c driver to use driver model and update boards which
use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Convert the sandbox TPM driver to use driver model. Add it to the device
tree so that it can be found on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new uclass for TPMs which uses almost the same TIS (TPM Interface
Specification) as is currently implemented. Since init() is handled by the
normal driver model probe() method, we don't need to implement that. Also
rename the transfer method to xfer() which is a less clumbsy name.
Once all drivers and users are converted to driver model we can remove the
old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use a _US suffix for microseconds and a _MS suffic for milliseconds. Move
all timeouts and delays into one place. Use mdelay() instead of udelay()
where appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use the same prefix on each function for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move all the init and uninit code into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some definitions are in the C file and some are in the header file. Move
everything into the header file for consistency and to reduce clutter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
There are too many structures storing the same sort of information. Move the
fields from struct tpm into struct tpm_chip and remove the former struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
There are too many structures storing the same sort of information. Move the
fields from struct tpm_dev into struct tpm_chip and remove the former
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This function is misnamed since it only applies to a single driver. Merge
its fields into its parent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The function methods in struct tpm_vendor_specific just call local functions.
Change the code to use a direct call.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The current Infineon I2C TPM driver is written in two parts, intended to
support use with other I2C devices. However we don't have any users and the
Atmel I2C TPM device does not use this file.
We should simplify this and remove the unused abstration. As a first step,
move the code into one file.
Also the name tpm_private.h suggests that the header file is generic to all
TPMs but it is not. Rename it indicate that it relates only to this driver
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add an SPDX header to two drivers that don't have it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add new Kconfig options for TPMs in preparation for moving boards to use
Kconfig for TPM configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard<christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is not used anymore by any board so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make "Generic Driver Options" menu show on the top in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add Kconfig entries for the simple-bus driver, both for U-Boot
and for SPL. The simple-bus is enabled by default in U-Boot and
disabled by default in SPL to preserve the original behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Modified to fit on top of Masahiro's $(SPL) setup:
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Originally a timeout value of 2 seconds was used regardless of the size
of data to be transfered. This prevented slow devices from working
correctly while there was no much gain for faster devices, e.g. it takes
3708ms for a transfer of uImage of size 1899008 bytes.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
Some status flags remain set until you explicetly clear the bit
in the status register.
Fix the SPL implementation to avoid false positive.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[hdegoede@redhat.com: Port from v2015.07 to v2015.10]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We only ever use syndrome mode for the partitions which contain the SPL,
as that is required for the BROM to be able to read the SPL.
Instead of using some arbritray limit for deciding whether or not to
use syndrome, be smart and check if u-boot-dtb.bin is directly behind
the SPL, if it is not then it is on its own partition and we should not
use syndrome.
Note the reason why we only use syndrome mode for the SPL is because it
comeswith weaker randomization, introducing a risk for more bit errors,
so we want to avoid it when possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The BROM does not care / use bad page markings, instead it deals with
any bad pages in the first erase-block by simply trying to load "boot0"
from the next erase-block.
This commit implements the same strategy for the sunxi spl nand code,
allowing it to boot from the backup boot partition when the main boot
partition is bad (tested by erasing the main boot partition).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Auto detect the nand configuration parameters, like the BROM does.
This allows us to get rid of various Kconfig settings, and is
necessary to support generic boards like the mk802 which have seen
many production runs with different nands.
The full blown u-boot/kernel nand driver uses the nand id to determine
this info, for the SPL we do as the BROM does and simply try a few
standard configs.
Note the table only contains configs which are known to actually be used,
rather then all the configs the BROM tries. This means that it may need
to be updated in the future as we add support for nand on more boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Parametrize the lowlevel nand_read_page function, instead of directly
using the CONFIG_foo settings for page-size, etc. there and add a few
wrappers / helper functions for calling it.
This is a preparation patch for adding auto-detecting of the nand
parameters like the BROM does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Properly config page-size in the nand ctl register, it seems that things
work fine without doing this, but still lets play it safe and properly
set the page-size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.
Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Sync the code for figuring out the ecc_mode and ecc_offset with the linux
kernel v4.1. Keeping this in sync seems like a good idea in general, and
it fixes / adds support for ecc strengths of 56, 60 and 64 bits.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We are using dma, so we should flush the cache before starting the dma,
and invalidate it once the dma is done.
Things are working without this by mostly luck, but lets not rely on that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Turn off the nand and dma clocks when we're done with the nand, this
puts the nand and dma controllers back into a clean state for when the
kernel boots.
Without this the kernel will not boot properly when it is built with
dma-controller support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In syndrome mode we set the NFC_SEQ bit in the command register, so the
spare-area register is not used. Also the value currently being written is
actual wrong, the ecc sits at "column + CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE"
not just CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE.
So the current code only serves to confuse the user -> remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There is no need to reset the nand chip for every ecc-block read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
nand_spl_load_image() always gets called with either CONFIG_SYS_TEXT_BASE
or spl_image.load_addr as destination, both of which are properly aligened,
and have plenty of space for "overshooting" up to
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes, as we read in
CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE bytes chunks.
This saves CONFIG_NAND_SUNXI_SPL_ECC_PAGE_SIZE (typically 1k) in
SPL size, which is a lot on the total 24k we have.
Note this changes the dma destination from SRAM to DRAM, so this patch
updates the DDMA_DST_TYPE bits in the dma controller cfg0 reg accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Drop the no longer accurate part of the USB_MUSB_SUNXI Kconfig help text,
since the musb-host code now supports the device-model, ehci and musb in
host mode can both be enabled at the same time without issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary
because on some boards the 1.2V default does not work reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Discard the empty video_set_lut function from platform video
drivers.
This commit "69d275458893eaec35229b589092c2a6bde5440f" introduces
a weak function video_set_lut, so we do not need an strong function
in platform drivers, which does nothing.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver is enabled only for UniPhier SoCs and ARCH_UNIPHIER now
selects OF_CONTROL and SPL_OF_CONTROL.
This driver no longer needs to support platform data configuration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 2580a2a7e7 ("mtd: nand: Increase max sizes of OOB and
Page size"), three boards (ph1_ld4, ph1_pro4, ph1_sld8) fail to build
with the following error message:
arm-linux-gnueabi-ld.bfd: SPL image plus BSS too big
They compile drivers/mtd/nand/denali_spl.c and it has a page_buffer
as static data:
static uint8_t page_buffer[NAND_MAX_PAGESIZE];
This buffer required 8KB in .bss section before that commit and now
it has been increased to 16KB. Given limited code/memory size for SPL,
it is not a good idea to allocate a page buffer statically. In the
first place, the load address 'dst' can be used as a page buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Claudiu Manoil
Prabhakar Kushwaha
Priyanka Jain
Masahiro Yamada
Simon Glass
Bin Meng
Marek Vasut
Yousong Zhou
Hans de Goede
Boris Brezillon
Peng Fan