The main PLL frequency is 2GHz for Armada-XP and 1GHZ for Armada 375,
38x and 39x.
[ Linux commit ae142bd9976532aa5232ab0b00e621690d8bfe6a ]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Compared to the Armada 3700, the Armada 7K and 8K are much more on the
high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as
opposed to the Cortex-A53 for the Armada 3700.
The Armada 7K and 8K also use a fairly unique architecture, internally
they are composed of several components:
- One AP (Application Processor), which contains the processor itself
and a few core hardware blocks. The AP used in the Armada 7K and 8K
is called AP806, and is available in two configurations:
dual Cortex-A72 and quad Cortex-A72.
- One or two CP (Communication Processor), which contain most of the I/O
interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one
CP, while the 8K family chips integrate two CPs, providing two times
the number of I/O interfaces available in the CP.
The CP used in the 7K and 8K is called CP110.
All in all, this gives the following combinations:
- Armada 7020, which is a dual Cortex-A72 with one CP
- Armada 7040, which is a quad Cortex-A72 with one CP
- Armada 8020, which is a dual Cortex-A72 with two CPs
- Armada 8040, which is a quad Cortex-A72 with two CPs
This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support,
starting with the Marvell DB-88F7040 development board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
The Armada 3700 integrates the following interfaces (not complete list):
- Dual Cortex-A53 ARMv8
- USB 3.0
- SATA 3.0
- PCIe 2.0
- 2 x Gigabit Ethernet 1Gbps / 2.5Gbps
- ...
This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support
for the Marvell DB-88F3720 development board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
The NAND interface on the Armada-38x series is similar to that on the
Armada-XP. The key difference is that the NAND ECC clock ratio is
provided via the DFX Server registers instead of the Core Clock.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Armada 375. Please note that
currently the SerDes and DDR3 init code for the A375 is not
included / enabled. This will be done in a later, follow-up patch.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the LCD controller of the Marvell
Armada XP SoC.
An AXP based custom board port will be added later, to use this
driver to display a splash screen via the bmp command later.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds basic support for Marvell's MV78230 SoC which belongs to the
Armada XP series.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Armada XP has support for X4 lanes, boards specify this in their
serdes_cfg. During PEX init in high_speed_env_lib.c, the configuration
is stored in GEN_PURP_RES_2_REG.
When enumerating PEX, subsequent interfaces of an X4 lane must be
skipped. Otherwise the enumeration hangs up the board.
The way this is implemented here is not exactly beautiful, but it mimics
how Marvell's BSP does it. Alternatively we could get the information
using board_serdes_cfg_get(), but that won't lead to clean code, either.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds runtime detection of the Marvell UART boot-mode (xmodem
protocol). If this boot-mode is detected, SPL will return to the
BootROM to continue the UART booting.
With this patch its now possible, to generate a U-Boot image that
can be booted either from the strapped boot-device (e.g. SPI NOR, MMC,
etc) or via the xmodem protocol from the UART. In the UART case,
the kwboot tool will dynamically insert the UART boot-device type
into the image. And also patch the load address in the header, so
that the mkimage header will be skipped (as its not expected by the
Marvell BootROM).
This simplifies the development for Armada XP / 38x based boards.
As no special images need to be generated by selecting the
MVEBU_BOOTROM_UARTBOOT Kconfig option.
Since the Kconfig option MVEBU_BOOTROM_UARTBOOT is not needed any
more, its now completely removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
This patch adds runtime boot-device detection to SPL U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
This is preparation for the runtime bootmode detection in spl.c.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
This patch adds support for the dual core Armada XP variant, the
MV78260. It has some minor differences to the 4-core MV78460,
e.g. only 12 serdes lanes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>
This patch removes the call to arch_cpu_init() in the SPL U-Boot version.
As SPL does not need all the configuration done in this function. And
also does not need the reconfiguration of the internal register
address to 0xf1000000. This will be done by the main U-Boot later on.
This also fixes a problem with the timer not beeing initialized on AXP,
as needed for the mdelay in the setup_usb_phys(). This will now only
be called once in main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the use of the kwboot tool, to boot mainline U-Boot
on the Marvell Armada XP/38x SoC's. This is done by returning to the
SoC's BootROM after SPL has initialized the SDRAM. We need to make sure
to not reconfigure the internal register space and MBARs. Otherwise
the BootROM will not be able to continue after SPL jumps back to it.
To use this feature, please don't forget to change the BOOT_FROM line
in your board specfic kwbimage.cfg file this way:
BOOT_FROM uart
Tested on these Marvell eval boards:
DB-MV784MP-GP - Armada XP
DB-88F6820-GP - Armada 38x
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch enables the USB EHCI support for the Marvell Armada XP (AXP)
SoCs. In compatism to the Armada 38x (A38x), the AXP needs to configure
the USB PLL and the USB PHY's specifically in U-Boot. The A38x has done
this already in the bin_hdr (SPL U-Boot). Without this, accessing the
controller registers in U-Boot or Linux will hang the CPU.
Additionally, the AXP uses a different USB EHCI base address. This
patch also takes care of this by runtime SoC detection in the Marvell
EHCI driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the NAND controller on the Armada XP/38x and provides
a new function that returns the NAND controller input clock. This
function will be used by the MVEBU NAND driver.
As part of this patch, the multiple BIT macro definitions are moved
to a common place in soc.h.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Accessing MBUS windows not backed-up by e.g. PCIe devices will
hang the SoC. Disable MBUS error propagation back to CPU allows
to read 0xffffffff instead of hanging the SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With this patch, the MBUS bridge registers (base and size) are
configured upon each call to mbus_dt_setup_win(). This is needed, since
the board code can also call this function in later boot stages. As
done in the maxbcm board.
This is needed to fix a problem with the secondary CPU's not booting
in Linux on AXP.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
On A38x switching the regs base address without running from
SDRAM doesn't seem to work. So let the SPL still use the
default base address and switch to the new address in the
mail u-boot later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
MAX_MVNETA_DEVS is not used anywhere in U-Boot. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*
Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This basic support for the Marvell Armada XP is base on the existing kirkwood
support. Which has been generatized by moving some common files into
common marvell locations.
This is in preparation for the upcoming Armada XP MV78460 support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Chris Packham
Stefan Roese
Chris Packham
Phil Sutter
Heiko Schocher
Anton Schubert