CS4315 PHY doesn't support phy-reset by software, it
needs to reset it by hardware via CPLD control.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_string instead of fdt_setprop to fix string length.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
As well updated T1024RDB to add T1023RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
We are about to change the location for ps7_init files, breaking the
current work-flows. It is good time to drop the legacy ps7_init.c/h
support.
Going forward, please use ps7_init_gpl.c/h all the time.
If you are still using old Xilinx tools that are only able to
generate ps7_init.c/h, rename them into ps7_init_gpl.c/h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is possible for CONFIG_XILINX_EMACLITE to be defined without
XILINX_EMACLITE_BASEADDR being defined as the EMAC Lite driver support
OF init. Check that the driver is enabled and the base address is
available before initializing with a static base address.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of hardcoding the 'fdtfile' variable, let's detect the SoC and
board variant on the fly and change the dtb name.
Based on the scheme done on am335x board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce is_hummingboard() function that reads GPIOs that can distinguish
between Cubox-i and Hummingboard.
Print the board name accordingly.
Based on a patch from Rabeeh Khoury.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad. Add support for the different SoC/memory sizes
combinations.
DDR initialization values were extracted from Solid-run internal U-boot.
Tested on a CuBox-i4Pro, HummingBoard-i2eX and HummingBoard-i1.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad.
Use IOMUX_PADS() macro in order to prepare for the multi-SoC support.
Also pass 'MX6QDL' in the defconfig to indicate it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The correct name of the defconfig file is 'mx6cuboxi_defconfig'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
Use "qixis_reset nand" to reset the board to boot from NAND.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds initial support for Colibri VF50/VF61 based on Freescale
Vybrid SoC.
- CPU clocked at 396/500 MHz
- DDR3 at 396MHz
- for VF50, use PLL2 as memory clock (synchronous mode)
- for VF61, use PLL1 as memory clock (asynchronous mode)
- Console on UART0 (Colibri UART_A)
- Ethernet on FEC1
- PLL5 based RMII clocking (E.g. No external crystal)
- UART_A and UART_C I/O muxing
- Boot from NAND by default
Tested on Colibri VF50/VF61 booting using serial loader over UART.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.
All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch populates serial number environment variable from
die_id_0 and die_id_1 register values for DRA7xx boards.
The function is added in omap common code so that this can be re-used.
Serial# environment variable will be useful to show correct
information in "fastboot devices" commands.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peter Howard <phoward@gme.net.au>
[trini: Add config file, update for ..._ether_addr() -> ..._ethaddr() rename]
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS2085ARDB is a evaluation platform that supports LS2085A
family SoCs. This patch add sbasic support for the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Add support for reset_cpu() by asserting RESET_REQ_B.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
This assignment conflicts with code that add flags with
gd->flags |= FOO prior to the execution of this function.
Seems like a historical artifact and creates bugs with
early alloc().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Commit d8bafe1310
"ARMv8: enable DM in vexpress64 board" only enabled DM
for the simulated vexpress64 board (FVP) with the
hardcoded clock value for the simulated board, causing
a console regression on the Juno board which was using
a different clock setting.
Fix this by enabling DM for all vexpress64 boards,
defining the clock frequency per-board, deleting the
static array of PL01x ports from the config file and
relying solely on the port defined in the boardfile
using platform data.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
some pins on the board have been rerouted to other peripherals, so we
change the pinmux to apply with hardware-design.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The NAND-version has been become a bit orphan.
Now we need to reactivate it, so bring necessary things:
- loading devicetree
- switch control signal to correct pins
- setup pinmux
- default-environment
up to date.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
instead of polling everytime the environment, we take usage of the global
gd->fdt_blob variable and check it only against NULL.
Variable "dtbaddr" from environment is needed only one time on loading the
devicetree within "load_devicetree()"
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
mx6sabresd has four MT41K128M16JT-125 chips. Each memory has 16-bit bus
and 2GiB, so fix the width and density fields accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move the compilation of file fsl_validate.c in MACRO CONFIG_CMD_ESBC_VALIDATE.
This file should be compiled only when the above MACRO is defined
This caused a break in compilation of iMX platforms when compiling for SECURE_BOOT
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
This commit combines catching missing memory and calibration data into
one if() block. It further prints pertinent information in determining
why the failure occurred.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory configuration for an IMX6SDL + 1GB density DRAM.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The initial revision of the GW551x does not connect enough signals between
the HDMI receiver and the IMX6 CSI for 16bit capture mode necessary for
yuv422smp capture. Future revisions will, but for the initial rev force it
to yuv422bt656 mode which requires an 8bit video data bus.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The HDMI receiver used on the GW54xx and GW551x has a 16bit video data bus
interconnect between it and the IMX6 CSI. This can be used in two different
modes, each having advantages and disadvantages. Allow the hdmiinfmt env
var to specify which format is desired (yuv422smp or yuv422bt656).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW522x is functionally the same as a GW52xx except for PCIE_RST#
GPIO. Add a DT fixup to change this gpio upon bootup.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds information about the Gateworks System Controller to the gsc command
such as the firmware version, firmware CRC and status of the GSC watchdog
(if its enabled and if its tripped).
Additionally the 'gsc wd' command can be used to enable or disable the
watchdog with the following usage:
gsc wd enable [30|60]
gsc wd disable
Note that the GSC registers are battery-backed by the GSC coincell so once
eanbled, they remain enabled across power-cycles or until either the GSC
firmware has been updated or FLASH has been re-programmed by the Gateworks
JTAG adapter.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Configure kernel device-tree for display from env var. This is useful
to specify the display present when the device-tree supports multiple
non-detectable display configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Shengzhou Liu
Tang Yuantian
Chunhe Lan
York Sun
Michal Simek
Masahiro Yamada
Nathan Rossi
Fabio Estevam
Scott Wood
Jaiprakash Singh
Prabhakar Kushwaha
Sanchayan Maity
Stefan Agner
angelo@sysam.it
Dileep Katta
Peter Howard
pankaj chauhan
Linus Walleij
Hannes Petermaier
rev13@wp.pl
gaurav rana
Pushpal Sidhu
Tim Harvey