source "drivers/net/phy/Kconfig" source "drivers/net/pfe_eth/Kconfig" config DM_ETH bool "Enable Driver Model for Ethernet drivers" depends on DM help Enable driver model for Ethernet. The eth_*() interface will be implemented by the UCLASS_ETH class This is currently implemented in net/eth-uclass.c Look in include/net.h for details. config DRIVER_TI_CPSW bool "TI Common Platform Ethernet Switch" select PHYLIB help This driver supports the TI three port switch gigabit ethernet subsystem found in the TI SoCs. menuconfig NETDEVICES bool "Network device support" depends on NET default y if DM_ETH help You must select Y to enable any network device support Generally if you have any networking support this is a given If unsure, say Y if NETDEVICES config PHY_GIGE bool "Enable GbE PHY status parsing and configuration" help Enables support for parsing the status output and for configuring GbE PHYs (affects the inner workings of some commands and miiphyutil.c). config AG7XXX bool "Atheros AG7xxx Ethernet MAC support" depends on DM_ETH && ARCH_ATH79 select PHYLIB help This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. config ALTERA_TSE bool "Altera Triple-Speed Ethernet MAC support" depends on DM_ETH select PHYLIB help This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. Please find details on the "Triple-Speed Ethernet MegaCore Function Resource Center" of Altera. config BCM_SF2_ETH bool "Broadcom SF2 (Starfighter2) Ethernet support" select PHYLIB help This is an abstract framework which provides a generic interface to MAC and DMA management for multiple Broadcom SoCs such as Cygnus, NSP and bcm28155_ap platforms. config BCM_SF2_ETH_DEFAULT_PORT int "Broadcom SF2 (Starfighter2) Ethernet default port number" depends on BCM_SF2_ETH default 0 help Default port number for the Starfighter2 ethernet driver. config BCM_SF2_ETH_GMAC bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" depends on BCM_SF2_ETH help This flag enables the ethernet support for Broadcom platforms with GMAC such as Cygnus. This driver is based on the framework provided by the BCM_SF2_ETH driver. Say Y to any bcmcygnus based platforms. config DWC_ETH_QOS bool "Synopsys DWC Ethernet QOS device support" depends on DM_ETH select PHYLIB help This driver supports the Synopsys Designware Ethernet QOS (Quality Of Service) IP block. The IP supports many options for bus type, clocking/reset structure, and feature list. This driver currently supports the specific configuration used in NVIDIA's Tegra186 chip, but should be extensible to other combinations quite easily. config E1000 bool "Intel PRO/1000 Gigabit Ethernet support" help This driver supports Intel(R) PRO/1000 gigabit ethernet family of adapters. For more information on how to identify your adapter, go to the Adapter & Driver ID Guide at: config E1000_SPI_GENERIC bool "Allow access to the Intel 8257x SPI bus" depends on E1000 help Allow generic access to the SPI bus on the Intel 8257x, for example with the "sspi" command. config E1000_SPI bool "Enable SPI bus utility code" depends on E1000 help Utility code for direct access to the SPI bus on Intel 8257x. This does not do anything useful unless you set at least one of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. config CMD_E1000 bool "Enable the e1000 command" depends on E1000 help This enables the 'e1000' management command for E1000 devices. When used on devices with SPI support you can reprogram the EEPROM from U-Boot. config ETH_SANDBOX depends on DM_ETH && SANDBOX default y bool "Sandbox: Mocked Ethernet driver" help This driver simply responds with fake ARP replies and ping replies that are used to verify network stack functionality This driver is particularly useful in the test/dm/eth.c tests config ETH_SANDBOX_RAW depends on DM_ETH && SANDBOX default y bool "Sandbox: Bridge to Linux Raw Sockets" help This driver is a bridge from the bottom of the network stack in U-Boot to the RAW AF_PACKET API in Linux. This allows real network traffic to be tested from within sandbox. See board/sandbox/README.sandbox for more details. config ETH_DESIGNWARE bool "Synopsys Designware Ethernet MAC" select PHYLIB help This MAC is present in SoCs from various vendors. It supports 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to provide the PHY (physical media interface). config ETH_DESIGNWARE_SOCFPGA bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC" depends on DM_ETH && ETH_DESIGNWARE help The Altera SoCFPGA requires additional configuration of the Altera system manager to correctly interface with the PHY. This code handles those SoC specifics. config ETHOC bool "OpenCores 10/100 Mbps Ethernet MAC" help This MAC is present in OpenRISC and Xtensa XTFPGA boards. config FEC_MXC_SHARE_MDIO bool "Share the MDIO bus for FEC controller" depends on FEC_MXC config FEC_MXC_MDIO_BASE hex "MDIO base address for the FEC controller" depends on FEC_MXC_SHARE_MDIO help This specifies the MDIO registers base address. It is used when two FEC controllers share MDIO bus. config FEC_MXC bool "FEC Ethernet controller" depends on MX5 || MX6 || MX7 help This driver supports the 10/100 Fast Ethernet controller for NXP i.MX processors. config FTMAC100 bool "Ftmac100 Ethernet Support" help This MAC is present in Andestech SoCs. config MVGBE bool "Marvell Orion5x/Kirkwood network interface support" depends on KIRKWOOD || ORION5X select PHYLIB if DM_ETH help This driver supports the network interface units in the Marvell Orion5x and Kirkwood SoCs config MVNETA bool "Marvell Armada XP/385/3700 network interface support" depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 select PHYLIB help This driver supports the network interface units in the Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs config MVPP2 bool "Marvell Armada 375/7K/8K network interface support" depends on ARMADA_375 || ARMADA_8K select PHYLIB help This driver supports the network interface units in the Marvell ARMADA 375, 7K and 8K SoCs. config MACB bool "Cadence MACB/GEM Ethernet Interface" depends on DM_ETH select PHYLIB help The Cadence MACB ethernet interface is found on many Atmel AT91 and SAMA5 parts. This driver also supports the Cadence GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. Say Y to include support for the MACB/GEM chip. config MACB_ZYNQ bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" depends on MACB help The Cadence MACB ethernet interface was used on Zynq platform. Say Y to enable support for the MACB/GEM in Zynq chip. config PCH_GBE bool "Intel Platform Controller Hub EG20T GMAC driver" depends on DM_ETH && DM_PCI select PHYLIB help This MAC is present in Intel Platform Controller Hub EG20T. It supports 10/100/1000 Mbps operation. config RGMII bool "Enable RGMII" help Enable the support of the Reduced Gigabit Media-Independent Interface (RGMII). config MII bool "Enable MII" help Enable support of the Media-Independent Interface (MII) config RTL8139 bool "Realtek 8139 series Ethernet controller driver" help This driver supports Realtek 8139 series fast ethernet family of PCI chipsets/adapters. config RTL8169 bool "Realtek 8169 series Ethernet controller driver" help This driver supports Realtek 8169 series gigabit ethernet family of PCI/PCIe chipsets/adapters. config SMC911X bool "SMSC LAN911x and LAN921x controller driver" if SMC911X config SMC911X_BASE hex "SMC911X Base Address" help Define this to hold the physical address of the device (I/O space) choice prompt "SMC911X bus width" default SMC911X_16_BIT config SMC911X_32_BIT bool "Enable 32-bit interface" config SMC911X_16_BIT bool "Enable 16-bit interface" help Define this if data bus is 16 bits. If your processor automatically converts one 32 bit word to two 16 bit words you may also try CONFIG_SMC911X_32_BIT. endchoice endif #SMC911X config SUN7I_GMAC bool "Enable Allwinner GMAC Ethernet support" help Enable the support for Sun7i GMAC Ethernet controller config SUN7I_GMAC_FORCE_TXERR bool "Force PA17 as gmac function" depends on SUN7I_GMAC help Some ethernet phys needs TXERR control. Since the GMAC doesn't have such signal, setting PA17 as GMAC function makes the pin output low, which enables data transmission. config SUN4I_EMAC bool "Allwinner Sun4i Ethernet MAC support" depends on DM_ETH select PHYLIB help This driver supports the Allwinner based SUN4I Ethernet MAC. config SUN8I_EMAC bool "Allwinner Sun8i Ethernet MAC support" depends on DM_ETH select PHYLIB select PHY_GIGE help This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. It can be found in H3/A64/A83T based SoCs and compatible with both External and Internal PHYs. config SH_ETHER bool "Renesas SH Ethernet MAC" select PHYLIB help This driver supports the Ethernet for Renesas SH and ARM SoCs. config DRIVER_TI_EMAC bool "TI Davinci EMAC" help Support for davinci emac config XILINX_AXIEMAC depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) select PHYLIB select MII bool "Xilinx AXI Ethernet" help This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. config XILINX_EMACLITE depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS) select PHYLIB select MII bool "Xilinx Ethernetlite" help This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. config ZYNQ_GEM depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL) select PHYLIB bool "Xilinx Ethernet GEM" help This MAC is present in Xilinx Zynq and ZynqMP SoCs. config PIC32_ETH bool "Microchip PIC32 Ethernet Support" depends on DM_ETH && MACH_PIC32 select PHYLIB help This driver implements 10/100 Mbps Ethernet and MAC layer for Microchip PIC32 microcontrollers. config GMAC_ROCKCHIP bool "Rockchip Synopsys Designware Ethernet MAC" depends on DM_ETH && ETH_DESIGNWARE help This driver provides Rockchip SoCs network support based on the Synopsys Designware driver. config RENESAS_RAVB bool "Renesas Ethernet AVB MAC" depends on DM_ETH && RCAR_GEN3 select PHYLIB help This driver implements support for the Ethernet AVB block in Renesas M3 and H3 SoCs. config MPC8XX_FEC bool "Fast Ethernet Controller on MPC8XX" depends on MPC8xx select MII help This driver implements support for the Fast Ethernet Controller on MPC8XX config SNI_AVE bool "Socionext AVE Ethernet support" depends on DM_ETH && ARCH_UNIPHIER select PHYLIB select SYSCON select REGMAP help This driver implements support for the Socionext AVE Ethernet controller, as found on the Socionext UniPhier family. config ETHER_ON_FEC1 bool "FEC1" depends on MPC8XX_FEC default y config FEC1_PHY int "FEC1 PHY" depends on ETHER_ON_FEC1 default -1 help Define to the hardcoded PHY address which corresponds to the given FEC; i. e. #define CONFIG_FEC1_PHY 4 means that the PHY with address 4 is connected to FEC1 When set to -1, means to probe for first available. config PHY_NORXERR bool "PHY_NORXERR" depends on ETHER_ON_FEC1 default n help The PHY does not have a RXERR line (RMII only). (so program the FEC to ignore it). config ETHER_ON_FEC2 bool "FEC2" depends on MPC8XX_FEC && MPC885 default y config FEC2_PHY int "FEC2 PHY" depends on ETHER_ON_FEC2 default -1 help Define to the hardcoded PHY address which corresponds to the given FEC; i. e. #define CONFIG_FEC1_PHY 4 means that the PHY with address 4 is connected to FEC1 When set to -1, means to probe for first available. config FEC2_PHY_NORXERR bool "PHY_NORXERR" depends on ETHER_ON_FEC2 default n help The PHY does not have a RXERR line (RMII only). (so program the FEC to ignore it). config SYS_DPAA_QBMAN bool "Device tree fixup for QBMan on freescale SOCs" depends on (ARM || PPC) && !SPL_BUILD default y if ARCH_B4860 || \ ARCH_B4420 || \ ARCH_P1023 || \ ARCH_P2041 || \ ARCH_T1023 || \ ARCH_T1024 || \ ARCH_T1040 || \ ARCH_T1042 || \ ARCH_T2080 || \ ARCH_T2081 || \ ARCH_T4240 || \ ARCH_T4160 || \ ARCH_P4080 || \ ARCH_P3041 || \ ARCH_P5040 || \ ARCH_P5020 || \ ARCH_LS1043A || \ ARCH_LS1046A help QBman fixups to allow deep sleep in DPAA 1 SOCs config TSEC_ENET select PHYLIB bool "Enable Three-Speed Ethernet Controller" help This driver implements support for the (Enhanced) Three-Speed Ethernet Controller found on Freescale SoCs. endif # NETDEVICES